BLUSTREAM DA11ABL-WP-EU-V2 Bluetooth And Analogue Audio Dante Wall Plate User Guide
- June 1, 2024
- BLUSTREAM
Table of Contents
DA11ABL-WP-EU-V2 QUICK REFERENCE GUIDE
DA 11 A B L- WP- EU – V 2
Quick Reference Guide
Introduction
The DA11ABL-WP-EU-V2 is a multi-input / output wall plate to convert Bluetooth and analogue audio within a digital Dante® networked audio system. The DA11ABL-WP-EU-V2 converts 2 input channels of Bluetooth or unbalanced audio to Dante® digital audio, and 2 channels of Dante® audio to 2 x output channels of unbalanced audio. The DA11ABL-WP-EU-V2 is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply, offers support for AES67 RTP audio transport and magnetic faceplate design allows for both UK & EU backbox compatibility. The DA11ABLWP-EU-V2 is the ideal BYOD interface to allow any Bluetooth device to stream audio wirelessly to a Dante® audio system.
FEATURES:
- Dante® network wall plate interface for Bluetooth and analogue L/R audio inputs, and L/R audio outputs
- Converts 2ch Bluetooth, or un-balanced audio sources to Dante® audio
- Converts 2x Dante® audio channels to un-balanced audio outputs
- Adjustable input sensitivity from +24dBu to -28dBV and output gain from +20dBu to -28 dBV via web GUI or API
- Dante® Audio Supports 44.1, 48, 88.2 & 96 KHz sample rates @ 16, 24 & 32 Bit
- Configurable Dante® device latency (supports 2, 3, 4, 5 or 10ms configurable using Dante® Controller)
- Supports AES67 RTP audio transport
- Features Class 0 IEEE 802.3af PoE for powering of product from any PoE switch
- Supports power via 12V DC adapter (not included) for when network switch does not support PoE
- White magnetic faceplate surround allowing for both UK & EU backbox compatibility
- In-built web-GUI for configuration and control
Bluetooth
Bluetooth 5.0 technology allows for up to 2x simultaneous connections from
source audio devices, where the selected devices audio is received and sent
into the Dante network.
To connect a Bluetooth enabled device to the DA11ABL-WP-V2, press the Pair
button on the unit, go to the Bluetooth settings of the source audio device,
and enable Bluetooth connectivity. The DA11ABL-WP-EU-V2 will appear in the
list of available devices.
Dante Controller
Dante Controller software is required in order to setup and configure the
DA11ABL-WP-EU-V2 as well as control your Dante network. Audinate provide
extensive training videos and documentation on their website. This can be
found here: http://www.audinate.com/products/software/dante-controller
Upon connecting your DA11ABL-WP-EU-V2 to a compatible network, the Dante
Controller software should automatically discover the device. The DA11ABL-WP-
EU-V2 will appear in the Dante Controller with a name denoted with “DA11ABL-
WP-EU-V2”. On the “Routing” screen you can create audio routing between Dante
transmitters and receivers in your system.
Please ensure your PC is on the same network as your Dante devices. Dante is
not able to transmit over WiFi and it is recommended to hardwire into the
Dante network. Having multiple network devices enabled can also confuse the
Dante Controller software so it is recommended to disable WiFi during
configuration.
It is also
possible to change the settings of the DA11ABL-WP-EU-V2 under the “Device
Info” screen in the Dante Controller software. To do so, select the “Device
Config” menu.
Here we can adjust the sample rate and the encoding bit rate of the DA11ABL-
WP-EU-V2. Please note that Dante products can only transmit or receive audio
from other Dante products that are set up with the same sample rate. A
mismatch in sample rate may stop audio from transmitting.
Under the “Device Config” screen we can also adjust the latency of the
DA11ABL-WP-EU-V2 from 2, 3, 4, 5 or 10 milliseconds.
Web Interface Module
The DA11ABL-WP-EU-V2 features an in-built Web GUI which can be used for
control and configuration of the device.
By default the device is set to DHCP, however if a DHCP server (eg: network
router) is not installed the device will receive a link local address in the
169.254.xxx.xxx range. The device info screen of Dante Controller will provide
you with the IP address information of each unit.
By accessing the IP address of the DA11ABL-
WP-EU-V2 in your web browser, you will gain access the units web GUI.
The following details will allow you to log in to the admin section:
Default Username is: blustream
Default Password is: 1234
This will give access to change the network settings as required, as well as
configure the device.
Settings Page:
Connections
- Power Status Indicator – Illuminates when the devices is powered on power input
- Bluetooth Status Indicator – Illuminates when Bluetooth device is connected
- ID LED Indicator – Flashes when this device is identified through DantConfigurator
- Analogue Audio Input – 3.5mm stereo jack for unbalanced analogue audio input
- Bluetooth Pair Button – Press to make device discoverable for Bluetooth pairing, press 2 to 3 times to change audio source selection
- Analogue Audio Output – RCA L / R connector unbalanced analogue audio output
- Dante® Network Connection (PoE) – RJ45 connection to connect to network switch
- Power Port – Use 12V/1A DC adaptor (not included) when PoE is not available to power device
Specifications
Audio Input Connectors: 1 x Analogue Left / Right audio (3.5mm stereo
jack)
Audio Output Connectors: 2 x Analogue RCA (Left / Right)
Network Connectors: 1 x PoE Dante® Ethernet Connection (RJ45)
Bluetooth : Bluetooth V5.0 – SBC / MP3 / AAC / APT-X / APTX-LL / APTX-HD,
44.1K-48KHz 16 / 24Bit
Configuration Switches: 1 x Push button (connect / selection)
Firmware Upgrade: 1 x Micro-USB UART port
Module Dimensions (W x H x D): 74mm x 74mm x 50mm (without faceplate)
Faceplate Dimensions (W x H x D): 85mm x 85mm x 5mm
Cut Out Dimensions (W x H x D): 52mm x 55mm x 38mm
Mounting Hole Spacing: UK 60mm CTC, EU 60mm CTC
Backbox Requirements: UK single gang backbox / EU single gang backbox
Shipping Weight: 0.3kg
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Storage Temperature: – 4°F to 140°F (- 20°C to 60°C)
Power Supply: Class 1 IEEE 802.3af POE PD or 12V/1A DC, 2-Pin Phoenix
connector
Package Contents
- 1 x DA11ABL-WP-EU-V2
- 1 x Magnetic Faceplate
- 1 x Quick Reference Guide
Acknowledgements
Dante® is a registered trademark of Audinate Pty Ltd.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION – changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmentally safe
recycling.
www.blustream.com.au
www.blustream-us.com
www.blustream.co.uk
DA11ABL-WP-EU-V2_QRG_REVA1
Documents / Resources
|
BLUSTREAM DA11ABL-WP-EU-V2 Bluetooth And Analogue Audio Dante Wall
Plate
[pdf] User Guide
DA11ABL-WP-EU-V2 Bluetooth And Analogue Audio Dante Wall Plate, DA11ABL-WP-
EU-V2, Bluetooth And Analogue Audio Dante Wall Plate, Analogue Audio Dante
Wall Plate, Audio Dante Wall Plate, Dante Wall Plate, Wall Plate, Plate
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>