DEMERBOX DB2 Pesaro Green Speaker User Guide
- June 12, 2024
- DemerBox
Table of Contents
DEMERBOX DB2 Pesaro Green Speaker
Product Information
The DemerBox DB2 is a portable speaker that provides high-quality audio and is designed for outdoor use. It features a waterproof and sealed design, making it suitable for use in water or sand environments. The speaker has a built-in rechargeable battery that provides up to 40 hours of continuous playtime when fully charged. It also has volume controls and supports Bluetooth connectivity for wireless audio streaming.
CHARGING
First time use
- Charge the DemerBox DB2 fully before using for the first time.
- The light on the charger will turn from red to green when fully charged.
Charge Status
- The five green LED lights on the DemerBox DB2 control panel show the battery state of charge. When all five LEDs are lit up, it will have approximately 40 hours of continuous play time.
Preserving Battery Life
- For best long-term battery life, don’t leave the DemerBox DB2 plugged in for extended periods after the battery is charged.
Using the DemerBox
Single Unit Mode
Turn on the DemerBox DB2 by pressing the Power button . Find DemerBox under
your device’s Bluetooth® settings and select it.
Charging a Device Using the DB2
- Plug a device into the USB charge out port on the DB2.
- Turn on the DemerBox DB2. Keep in mind, a DB2 battery will drain faster if you’re charging a device from it.
Aux Cable
Plug one end of the AUX cable into the DemerBox DB2 and the other into the
audio output of your device.
Volume Controls
You can control the volume two ways:
- Use the volume controls on your device.
- Use the UP/DOWN arrow buttons on the front of the DemerBox. These only work in Bluetooth mode.
Using In and Around Water or Sand
IMPORTANT: Your DemerBox is only waterproof and sealed when the port plug is properly inserted!
To Insert the Port Plug
- Unscrew the port plug from its holder inside the DB2. To do this, use one hand to hold the port plug collar while using your other hand to turn the wings.
- Close the DB2 lid and latch it.
- Insert the port plug into the port tube outside the DB2 until the port plug is fully seated in the port hole. To do this, use one hand to hold the port plug collar and turn the port plug wings clockwise until the plug is secure in the port hole. A snug fit is all you need.
MULTI-cast Mode:
Connecting Multiple Speakers Together
Enable Multi-cast Mode for Speakers
- Choose a speaker and connect to it via Bluetooth. (This will be the ‘Primary’ speaker.)
- Next, press and hold the UP button until you hear “broadcast mode enabled”. The right LED light on the keypad will begin to blink.
- Turn ON another DB1 or DB2 speaker. (This speaker will be a ‘Satellite’ speaker.)
- On the second speaker, press and hold the DOWN button until you hear “broadcast audio enabled”. Both speakers are now ENABLED for multi-cast mode, and ready for pairing.
- To activate multi-cast pairing, quick press both the UP and DOWN volume buttons on the Primary speaker at the same time. Repeat this action on the Satellite speaker.
- a. The Primary DemerBox LEDs will start a back and forth tracking pattern.
- b. The Satellite DemerBox LEDs will alternate in a LEFT / RIGHT pattern.
- c. After a few seconds you should hear “paired.” You are now ready to listen to both speakers.
Exiting Multi-cast Mode
To exit multi-cast mode, hold down the UP/DOWN volume buttons for 5 seconds.
You can also turn the speaker OFF/ON .
Volume Control
When in multi-cast mode, the Primary speaker volume buttons control the volume
on all paired speakers. You can also use the volume control on your device.
Add an additional speaker
Once the boxes are in multi-cast pairing mode, they will stay active for 30
seconds. You maybe able to connect several more speakers to the Primary during
this time. (You will know if the speakers are active if they display the
LED patterns described in 5a, 5b above).
If you are adding another speaker more than 30 seconds after initial Primary and Satellite pairing, repeat steps 3-5c.