iMEC IASS 1000 Automatic Sensor Hand Sanitizer Dispenser Installation Guide

iMEC IASS 1000 Automatic Sensor Hand Sanitizer Dispenser

Product Information

• Product Name: IMEC IASS 1000 & IMEC IAF 1000
• Type: Dispenser
• Usage: Soap dispenser with pump

Product Usage Instructions

1. Insert the key into the locker located at the top of the dispenser and push down the key to unlock the dispenser cover.

2. Remove the soap refill container with the pump from the dispenser.

3. Place the dispenser on the wall within a distance of 15-25cm from the countertop or basin. Use a pencil to mark the location for drilling the hole.

4. Drill the wall at the marked location and insert the wall plug provided into the drilled hole.

5. Use the screws provided to securely attach the dispenser to the wall.

6. Put back the refill container with the pump into the dispenser, ensuring the arrow is aligned correctly.

7. Remove the battery compartment located on the left side of the pump and insert six (6) pieces of AA size alkaline batteries.
   Replace the battery compartment into the dispenser.

8. Open the cover of the refill container and refill it with IMEC 525F – Foam Soap for IMEC IAF 1000 or IMEC 585SC – Spray Clean Sanitizer / IMEC 585S – Hand Sanitizer for IMEC IASS 1000. Close the container cover when finished refilling.

9. Set the actuation of the pump on the right side of the pump using diagram no.11:

   • 1 – 1 pump/dispense
   • 2 – 2 pumps/dispense
   • 3 – 3 pumps/dispense

10. Close the dispenser cover. The LED light will flash 3 times to indicate that the dispenser is ready to use.

Notes:

1. The dispenser cover must close properly to activate the dispenser.
2. If the battery is low, the red light indicator will blink continuously (every second) and the dispenser will stop functioning. Change the battery immediately.
3. If the red light blinks 5 times in 1 second, it indicates that there is an object within 15-25cm below the dispenser. Remove the object or install the dispenser higher.
4. Do not take out the refill container during the refilling process.

INSTALLATION

push down the key and pull the dispenser cover down
2| Use diagram 6 but pull out the container & pump| Remove the soap refill container with the pump inside the dispenser
3| Use pic figure 1 to rep

the box and add pencil to mark the hole

| Place the dispenser on the wall within the distance of 15-25cm from countertops or basin. Use pencil to mark the location to drill
4| use diagram no 2 but remove the box (only leave the mark)| Drill the wall. Use the wall plug provided to insert into the drilled hole
5| | Use screws provided and screw the dispenser to the wall
6| use back picture step 3 only change arrow| Put back the refill container with the pump into the dispenser
7| | Remove the battery compartment (left side of the pump) and insert six (6) pieces of AA size alkaline batteries. Then put back the compartment into dispenser
8| | Open the cover of refill container and refill with IMEC 525F – Foam Soap for IMEC IAF 1000 & refill with IMEC 585SC – Spray Clean Sanitizer / IMEC 585S – Hand Sanitizer for IMEC IASS 1000. Close back the container

cover when finish refill

9| Use diagram no.11 but zoom out the pump

setting

| Set the actuation of the pump (right side of the pump)

1  – 1 pump/dispense

2  – 2 pump/dispense

3  – 3 pump/dispense

10| | Close the dispenser cover and the LED light will flash 3 times to indicate the
is ready to use

DISPENSER

Notes:

1. Dispenser cover must close properly to activate the dispenser.
2. If the battery is low, red light indicator will blink continuously (every second) and dispenser will stop functioning. Change the battery immediately.
3. If the red light blink 5 times in 1 second, the machine has been selfinductance whereby there’s an object within 15-25cm bottom of the dispenser. Remove the object or install the dispenser higher.
4. Do not take out the refill container during refilling process

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>