Tefal GV9150 Protect Turbo Steam Generator User Manual

Tefal GV9150 Protect Turbo Steam Generator

UNDERSTANDING YOUR STEAM GENERATOR

CONTROL PANEL

“PROTECT CONCEPT”™ SAFETY SYSTEM

Your generator is equipped with the “Protect Concept” system.

• Double protective flaps.
• Flap locking system engages automatically when flaps are closed over the iron, opened by pressing release button.
• Automatic heat shut-off when flaps are closed.
• Carrying handle.

IRONING POSITION
The appliance heats (if connected)

PROTECT CONCEPT
Automatic “Security Auto-stop” function which shuts off the heating of the appliance when the hood is closed over the iron

Your steam generator is equipped with an automatic “Security Auto-stop” function which cuts off the heating of the appliance when the flaps are closed over the iron.The control panel lights go out and the on indicator remains lit, showing that the appliance is connected but not heating.

PREPARING YOUR STEAM GENERATOR

1. To carry your steam generator:
   • place the iron on the iron rest of the generator and raise the hood over the iron until it locks into place (audible click) (1).
   • grasp the handle of the protective hood to carry your steam generator (2).
2. Place your steam generator on a stable, horizontal heat-resistant surface.
3. Grasp the handles of the removable tank and pull horizontally to remove it (3).
4. Fill up the water tank taking care not to exceed the maximum level just below the filler cover (4).
5. Replace it firmly in its housing, making sure it is fully in place (5).

The water to use in your steam generator:
Your steam generator has been designed to operate using untreated tap water. However, if your water is very hard, mix it 50% untreated tap water with 50% distilled water.

Types of water to be avoided:
Do not add anything to the contents of the removable water tank, and do not use water from clothes dryers, scented water, water from refrigerators, water air conditioners or rainwater. Also do not use filtered, boiled or bottled mineral water. These contain organic waste or mineral elements that become concentrated when heated and cause spitting, brown staining or premature wear to your iron.

USING YOUR STEAM GENERATOR

1. Press the release button for the 2-part protective hood and fold it down over the tank to release the iron (6).
2. Completely unwind the power cord from its storage space before connecting to an earthed socket (7).
3. Press on the on / off switch (located on the side of the base unit) (a): the green light (located on the control panel) flashes and the boiler heats up (b).It will take around 2 minutes for steam to be produced which is indicated when the green “steam ready” light stops flashing (8).
   

• The first time the appliance is used, there may be some fumes and smell but this is not harmful. They will not affect use and will disappear rapidly.
• When starting, and regularly while it is being used, your steam generator’s electric pump injects water into the boiler. It makes a noise but this is quite normal. You may also hear a clicking noise which is the steam valve opening. Again this is normal. If you are pressing on the steam control button at this time you may lose a little steam pressure momentarily.

OPERATING THE CONTROL PANEL

• Flashing green light: The water is heating up in the boiler.

• Continuous green light: Steam is ready for use.

• Continuous red light: The water tank is empty.

• Orange “boiler rinse” light flashes: your boiler needs rinsing.
  Note: The appliance must be cold.

• “Reset” button: to be held pressed for 2 or 3 seconds after rinsing the boiler.

USING YOUR STEAM GENERATOR

1. Place the iron’s temperature control slide according to the type of fabric to be ironed (9).

2. The thermostat light comes on. Be careful! The steam generator is ready when the thermostat light goes out and when the green “steam ready” light stays on.
   Note: It is normal for the steam cord to become warm during use.

3. Adjust the steam output control dial located on the control panel (10).

Set the temperature control slide and steam output control dial according to the type of fabric to be ironed:

Recommendations:

To prime the steam circuit, either before using the iron for the first time, or if you have not used the steam function for a few minutes, press the steam control button several times in a row, holding the iron away from your clothes.
This will enable any cold water to be removed from the steam circuit

• Iron temperature control slide setting: Start with the fabrics to be ironed at a low temperature (●) and finish with those that need higher temperatures (●●● or Max).
• Mixed fibre fabrics: set the ironing temperature to the setting for the most delicate fabric.
• Woollen garments: Press repeatedly on the steam control button to obtain short bursts of steam, without placing the iron on the garment itself. This will avoid making the fabric shiny.
• Steam output control dial setting:
  • Thick fabric: Increase the steam setting.
  • At a low temperature: set the steam output control dial to the low position.

To iron without using steam:

• Do not press the steam control button under the iron handle.
  Ironing Board: For best results, a mesh-type ironing board should be used to allow any excess steam to escape.

• If you are using starch, it should be sprayed onto the reverse side of the fabric to be ironed.

WHEN THE RED LIGHT “WATER TANK EMPTY” COMES ON

There is no more steam. The removable water tank is empty (12).

1. Raise the 2 parts of the hood over the iron until the protection system locks into place (audible click) (13).
2. Grasp the handles of the removable tank and pull horizontally to remove it ; fill with water.
3. Replace and push it firmly into place
4. Press the release button for the hood and fold it down over the tank (14).

VERTICAL STEAM IRONING

1. Set the iron temperature control slide and the steam output control dial (located on the control panel) to the MAX position.
2. Hang the garment on a coat hanger and hold the fabric slightly taut with one hand. As steam is very hot, never attempt to remove creases from a garment while it is being worn, always hang garment on a coat hanger.
3. Holding the iron in a vertical position, tilted slightly forwards, press repeatedly on the steam control button (under the iron handle) moving the iron from top to bottom (15).
   

Recommendations:
For fabrics other than linen or cotton, hold the iron a few centimetres from the garment to avoid burning the fabric.

TURBO STEAM FUNCTION

Press 2 or 3 times on the turbo steam button to obtain a more powerful burst of steam (16):

• for ironing thicker fabrics,
• to eliminate creases,
• for powerful vertical steaming.

Be careful:
Use the turbo steam function very carefully because of the exceptional power of steam that may cause burns.

NOTE:
Continuous use of the turbo steam function will begin to cool the iron and may cause water to drip from the iron. If this occurs, stop using the turbo steam function and allow the iron thermostat to reach temperature again (thermostat light will come on and go off) before using this function again.

MAINTAINING YOUR STEAM GENERATOR

• Before cleaning, ensure that your steam generator is unplugged and that the soleplate and the iron rest have cooled down.
• Do not use detergent or descaling products for cleaning the soleplate or the base unit.
• Never hold the iron or the base unit under the tap.
• Do not place the iron on a metal rest as this could damage it.

Place it on the iron-rest on the base unit: it has non-slip pads and has been designed to withstand high temperatures.

1. Empty and rinse the removable water tank (17).

2. Regularly clean the soleplate with a damp, non-metallic washing-up pad.

3. Clean the plastic parts of the appliance occasionally with a soft cloth.

THE ORANGE “BOILER RINSE” LIGHT FLASHES

Note:

• To extend the efficient operating life of your boiler and avoid scale particles on your linen, your generator is equipped with an orange “boiler rinse” warning light that flashes on the control panel after about 10 uses.
• If your water is hard, increase the frequency.
• Do not use descaling agents for rinsing out the boiler, as they could damage it.

TO RINSE THE BOILER USING A RINSING ACCESSORY

For greater effectiveness and for ease of operation, you are advised to use the rinsing accessory provided in the box. It will make it easier to rinse the boiler as the generator will need less handling. Your rinsing accessory has been designed to work on a wide range of taps. It is supplied with 2 types of membranes (a) (b). Choose the one best suited to your tap.

If you do not wish to, or cannot use the rinsing accessory, refer to the advice in paragraph II (next page). Before attempting to rinse the boiler of your generator, it is essential to leave it to cool for at least 2 hours in order to avoid any risk of scalding. If the orange “boiler rinse” light flashes, you can continue ironing normally but remember to rinse the boiler first, the next time that you use it.

1. Check that the generator is cold and unplugged.
2. The protective hood must be folded down over the tank.
3. Place your steam generator on the edge of your sink, with the iron to one side, standing on its heel.
4. Unscrew the cord clip by turning a quarter turn to the left (18).
5. Using a coin, gently unscrew the boiler rinse plug (19).
6. Place the plastic nozzle of the rinsing pipe into the hole of the boiler and turn gently to the right until it locks. The outlet of this nozzle must be positioned over the sink (20).
7. Connect the rubber end of the rinsing pipe to a cold tap (21).
8. Turn the tap on gently and gradually and let cold water run through the rinsing pipe into the sink for about 1 minute (22).
9. Switch off the tap and remove the rinsing pipe.
10. Screw back and tighten up the boiler rinse plug with a coin.
11. Put the cord clip back in place.
12. The next time you use the generator, hold down the “reset” button for 2 to 3 seconds to turn off the orange light.
    

TO RINSE THE BOILER WITHOUT THE RINSING ACCESSORY

Before attempting to rinse the boiler of your generator, it is essential to leave it to cool for at least 2 hours in order to avoid any risk of scalding. If the orange “boiler rinse” light flashes, you can continue ironing normally but remember to rinse the boiler first, the next time that you use it.

1. Check that the generator is cold and unplugged.
2. The protective hood must be folded down over the tank.
3. Place your steam generator on the edge of your sink, with the iron to one side, standing on its heel.
4. Unscrew the cord clip by turning a quarter turn to the left.
5. Using a coin, gently unscrew the boiler rinse plug.
6. Holding your steam generator in a tilted position, and using a jug, fill the boiler (in the base unit) with 1/4 litre of tap water.
7. Shake the base unit for a few moments and then empty it completely over your sink. To obtain the best result, we recommend that this operation is done twice.
8. Screw back and tighten up the boiler rinse plug with a coin.
9. Put the cord clip back in place.
10. The next time you use the generator, hold down the “reset” button for 2 to 3 seconds to turn off the orange light.

PUTTING YOUR STEAM GENERATOR AWAY

1. Place the iron on the rest.
2. Turn off the main O/I switch and unplug it.
3. Raise the 2 parts of the hood over the iron until the protection system locks into place (audible click) (23).
4. Retract the electric supply cord (24). On the model with an automatic reel, press the reel button and guide the cord with your free hand.
5. Store the steam cord by wrapping it around the casing and securing it in its retaining clip.
6. You can then put your steam generator away, carrying it by the handle (25).
   

ENVIRONMENT PROTECTION FIRST!
Your appliance contains valuable materials that can be recovered or recycled.

• Take it to a local civic waste collection point.
• Never dismantle your iron: always take it to an Approved Service Centre

HELPLINE
If you have any product problems or queries with your product, please telephone our Customer Relations team on : 0845 6021454 (UK) (Calls charged at local rate) (01) 4751947 (Ireland)
Consult our web site: www.tefal.co.uk

SAFETY RECOMMENDATIONS

Your steam generator is an electrical appliance. It should be used under normal conditions. It is intended for domestic use only.

• Your generator is fitted with 2 safety systems:
  

  • A pressure release valve which, in the event of a malfunction, releases any excess steam.
  • A thermal fuse to prevent the appliance from overheating.

• This appliance is not intended to be used by children or without supervision by persons whose physical, sensory or mental aptitude to use it in complete safety is impaired. Children must be supervised to ensure that they do not

• play with the appliance.

• The appliance must be used and placed on a stable, heat-resistant surface.

• Completely unwind the power cord from its storage space before connecting it to an earthed socket.

• Always plug your steam generator into:

• An electrical installation with a voltage between 220V and 240V. Connecting to the wrong voltage may cause irreparable damage to the appliance and will invalidate your guarantee.

• An earthed socket. If you are using a mains extension lead, ensure that it is correctly rated (10A) with an earth, and is fully extended.

• Should the power cord or the boiler cord linking the iron to the base unit become damaged, it must be replaced by a TEFAL-approved service centre to avoid the risk of danger or injury.

Be careful:

• The soleplate and generator iron rest can become very hot and cause burns:
  • never touch these parts.
• If you store your iron in a cupboard or confined space, ensure that it is left to cool before putting it away.
• Your appliance gives off steam which can cause burns.
• Handle your iron carefully, particularly when using the vertical steam function
• Never direct the steam towards persons or animals.
• Never touch the electric cords with the soleplate of the iron.
• Never leave the appliance unattended :
  • When it is connected to the mains
  • until it has cooled down (around 1 hour).
• Do not unplug the appliance by pulling on the cord.
• Always unplug your appliance :
  • Before rinsing out the boiler,
  • before cleaning your generator, after each use.
• Before unscrewing the boiler rinse plug, wait until the generator is cold (unplugged for more than 2 hours).
• Never fill the boiler through the rinse hole (except for rinsing)
• Never immerse your steam generator in water or any other liquid. Never hold it under the water tap
• While rinsing out the boiler, never fill it directly under the tap.
• The appliance must not be used if it has fallen to the floor, shows evidence of damage, leaks or fails to function correctly. Never dismantle your appliance.To avoid any danger, have it inspected in a TEFAL-approved service centre.
• If you lose or damage the boiler rinse plug, have it replaced by a TEFAL

Approved Service Centre.
This appliance is designed for domestic use only. In the case of professional use, inappropriate use or failure to comply with the instructions,TEFAL accepts no responsibility and the guarantee does not apply.

Troubleshooting

FAQ’s

What is the Tefal GV9150 Protect Turbo Steam Generator?

The Tefal GV9150 Protect Turbo Steam Generator is a high-performance steam ironing system designed to provide efficient and convenient ironing results.

How does the Protect Turbo technology work?

The Protect Turbo technology helps prevent garment damage by providing a perfect combination of steam and heat, making it suitable for a wide range of fabrics.

What is the power output of the steam generator?

The steam generator typically has a power output that provides consistent and powerful steam performance for effective ironing.

Does the steam generator have adjustable steam settings?

Yes, the Tefal GV9150 often features adjustable steam settings, allowing you to customize the steam output based on the type of fabric you're ironing.

What is the water tank capacity?

The steam generator's water tank usually has a generous capacity that allows for longer ironing sessions without frequent refills.

Is the steam generator equipped with an anti-calc system?

Yes, the steam generator often includes an anti-calc system to prevent limescale buildup, ensuring optimal steam performance and longevity.

Does the steam generator have a continuous steam feature?

Yes, the Tefal GV9150 often provides a continuous steam feature, enabling you to iron large garments or piles of laundry efficiently.

What safety features are included?

The steam generator may have safety features such as an auto-off function, secure locking system, and heat-resistant materials for safe and worry-free ironing.

Is the steam generator suitable for vertical steaming?

Yes, the Tefal GV9150 often supports vertical steaming, allowing you to remove wrinkles from hanging garments or curtains.

Is the steam generator easy to maintain?

Yes, the steam generator typically comes with features like a removable water tank and easy-to-clean surfaces for hassle-free maintenance.

What type of soleplate does the steam generator have?

The steam generator often features a high-quality soleplate that provides smooth gliding and even heat distribution for effective ironing.

What is the warranty period for the steam generator?

The warranty period for the Tefal GV9150 Protect Turbo Steam Generator may vary by region and retailer. Refer to the product documentation for warranty information.

Download This PDF Link:Tefal GV9150 Protect Turbo Steam Generator User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>