bryton Rider 460 GPS Bike Computer User Guide

Rider 460 GPS Bike Computer Quick Start Guide
www.brytonsport.com

Rider 460 GPS Bike Computer

Download UserManual

https://www.brytonsport.com/#/supportResult?tag=Manual

Download Bryton Active App

http://download.brytonsport.com/inst.html

Getting Started

Key Functions

A. Power/Backlight( ) : Press to turn the device on. Press to turn on/off the backlight while the device is on. Long Press to turn the device off.
B. Up ( ) :Press to scroll up the data screens and the options in Menu.
C. Down/Menu( ) : Press to scroll down the data screens and the options in the menu. Long press to enter the menu.
D. OK/Record/Pause ( ): In Menu, press to enter submenu or conrm a selection. In data page, press to start recording. When recording, press to manually pause.
E. Lap/Back ( ):In Menu, press to return to the previous page or cancel an operation. When recording, press to mark the lap.

Reboot Rider
Press ( ) at the same time to reboot the device.

Getting Started
Please charge your device for at least 4 hours before the first use.
To begin

1. Press to turn on the device.
2. select the display language/unit and press to confirm the selection.
3. Device will automatically search for satellite signals. You can view the GPS signals status on the screen or the quick status.
4. After GPS signal is fixed *, ( ) select to start the ride in free cycling mode.
5. To record, press to start recording.

Check and update your device firmware version via Bryton Active app.
To acquire GPS signals, allow the device access to an open sky, outdoor environment.

Follow Track
Go to “My Route” and tap the route. Click the “ ” to download it to the device. Then, in the Main Menu of the device, navigate to “Course” > “Route”. Find the route and tap to start following the track.

Rider 460 provides 3 ways to create tracks.

1. Plan trip via Bryton Active App.
2. Import GPX track files via Bryton Active app.
3. Auto sync routes from Strava, Komoot, and Ride With GPS.

Plan Trip via Bryton Active App

1. In the Bryton Active App, select “Course” >”My Route”> “Plan Trip” to set a Start point and Destination by tapping on the map or inputing address in the Search Bar.
2. After finishing planning, save the planned trip to “My Route” by tapping “Save”.

Import GPX track files via Bryton Active App

1. Download routes in GPX format from any other source.
2. Select “Open in Active”(for iOS) or Open files with Bryton Active App (for Android).
3. Select “Course” > “My Route” in Bryton Active App.
4. Here you can see the routes imported to the App.

Auto sync routes from Strava, Komoot and Ride With GPS

1. In the Bryton Active app, select “Course” >”My Route”>”3rd party account link”.
2. You can enable STRAVA/Komoot/RideWithGPS auto sync there.
3. Once authorized, you can see routes from those platforms in “My route” with their icons.

Data Sync
Sync Data to/from Bryton Active app
With the Bluetooth connection, your Rider computer can upload recorded tracks, download planned trips, and update the firmware via Bryton Active app. It is required to add your device to your Bryton Active account before syncing data for the first time.

To add.

1. Sign up / log in to your Bryton Active App account.
2. Go to “Settings” and click “+” to add a new device to your account.
3. Select your device and tap to add your device  to your Bryton Active account.
4. Your device is now successfully paired with the Bryton Active App.
5. Click the device icon to initiate the activity sync. You can enable the “Auto

Sync Track” feature as well.
Upload/Share Your Tracks via USB

1. Connect the device to your computer via USB cable.
2. Select fit files from Bryton -> Activities folder in the device.
3. Upload files to brytonactive.com and popular training sites such as STRAVA and Training Peaks.

Icon Description

| GPS Signal| | Pause| | Scale
(Alt. Chart)| | Control
(Trainer Control)
---|---|---|---|---|---|---|---
| Phone
Connected| | Current
Climb| | Altitude
Gain| | Sensor
Status On
| Live Track Activated| | point north| | Distance| | Sensor
Status Off
| Battery| | My Location
(Map)| | Owner
(Group Ride)| |
| Menu| | My Location
(Alt. Chart)| | Leader
(Group Ride)| |
| Recording| | Destination| | Issue
(Group Ride)| |

Note:

• For Firmware Update, please go to www.brytonsport.com> (Menu) > Support > Download.
• For Video Instructions, please go to www.brytonsport.com> (Menu) > Support > Tutorial.
• For User Manual, please go to www.brytonsport.com> (Menu) > Support > Download > Manual > User Manuals.

Install Rider 460

Mount Rider 460 to the Bike

(Optional)

Safety Lanyard

Install Heart Rate Belt (Optional)

**** Accuracy may be degraded by poor sensor contact, electrical interference, and receiver distance from transmitter.
The Bryton Smart HR Sensor contains a user-replaceable CR2032 battery.

**** To prolong the life of your heart rate monitor, detach the sensor and clean the strap after every use.

Sensors Pairing _ Heart Rate Sensor

**** RF Exposure Information (MPE)
This device meets the EU requirements and the International Commission on Non- Ionizing Radiation Protection (ICNIRP) on the limitation of exposure of the general public to electromagnetic Fields by way of health protection. To comply with the RF exposure requirements, this equipment must be operated in a minimum of 20 cm separation distance to the user.
Hereby, Bryton Inc. declares that the radio equipment type Bryton product is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.brytonsport.com/download/Docs/CeDocs_Rider460.pdf
For more information on E-label regulations and compliance, as well as identification markers, relevant software, product and licensing information and other regulatory information provided by the FCC or regional compliance markings, please navigate to Settings > About.

Restricted Substances and Its Chemical Symbols
Unit| Lead
(Pb)| Mercury
(Hg)| Cadmium
(Cd)| Hexavalent
chromium
(Cr+6)| Polybrominated
biphenyls
(PBB)| Polybrominated
diphenyl ethers
(PBDE)
Shell| | | | | |
Circuit board| | | | | |
The screen| | | | | |
Cable| | | | | |

Note 1: “Exceeding 0.1 wt %”and“exceeding 0.01 wt %”indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2: The“ ○ ” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: The “−” indicates that the restricted substance corresponds to the exemption.

Install the Cadence Sensor (Optional)

**** Remove battery tab before use.
The Bryton Smart Speed / Cadence Sensor contains a user-replaceable CR2032 battery.

Sensors Pairing _ Cadence Sensor

Pairing Bryton Smart Sensors with Your ANT+ / BLE Devices
After installing Bryton Smart Sensors, rotate crank and wheel a few times to wake Bryton Smart Sensors up. The sensors can only be paired when they are awake, or they would go back to sleep to preserve power.

Note:

1. The pairing steps differ from each Bryton device. Please check its own user manual.
2. Please keep away from other ANT+ or BLE sensors while pairing.

Connecting to Your ANT+ / BLE Devices
After pairing, your Bryton devices automatically connect to Bryton Smart Sensors each time when the sensors are awake.

Rider 460 Specifications

www.thisisant.com/directory for compatible products.

GNSS| Integrated high-sensitivity GNSS receiver with embedded antenna
BLE Smart| Bluetooth smart wireless technology with embedded antenna;
2.4GHz band 0dBm
Water Resistant| Water resistant to a depth of 1 meter for up to 30 minutes.
Barometer| Equipped with barometer

Designed by Bryton Inc.
Copyright 2023 Bryton Inc. All rights reserved.
3F-1, No.79-1, Zhouzi St., Neihu Dist., Taipei City 114, Taiwan (R.O.C.)
The content of this manual is subject to change without prior notice.

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television  reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to  operate this equipment. (Example ‐ use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body.
This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co‐located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada licence-exempt RSS-247 standard.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

References

• Strava | Running, Cycling & Hiking App - Train, Track & Share
• Bryton
• Bryton
• Directory - THIS IS ANT
• Bryton Active
• Strava | Running, Cycling & Hiking App - Train, Track & Share

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>