ZWILLING 53002-000-0 Enfinigy-Table Blender Instruction Manual
- June 12, 2024
- ZWILLING
Table of Contents
ZWILLING 53002-000-0 Enfinigy-Table Blender Instruction Manual
Safety
Read these operating instructions in their entirety and with care before using
the blender.
Keep these operating instructions in a safe place. If you transfer the blender
to a third party, ensure that you include the operating instructions in such a
transfer.
Non-observance of these operating instructions can lead to serious injury or damage to the appliance. Zwilling does not accept any liability for damage caused by non-observance of these operating instructions.
Important information for your safety is specifically marked. Make sure to observe this information in order to avoid accidents and damage to the appliance
Safety information
The blender (hereinafter referred to as the “appliance”) is intended exclusively for crushing and mixing ingredients for beverages, liquid foods (dips, soups, sauces, pesto) and ice cubes. It may only be used with the accessories supplied or approved by Zwilling.
Any other use is considered improper and may result in personal injury or property damage.
Do not put any hot fats, oils, or objects in the appliance.
The appliance is intended for domestic use. It is not intended for commercial use. Certain persons are at greater risk:
This appliance may be used by children 8 years of age and older and by persons with reduced physical, sensory or mental capacity or with a lack of experience and knowledge, if such children and persons are supervised or have been instructed in the safe use of the appliance and understand the hazards resulting from using the appliance.
Children are not allowed to play with the appliance. Cleaning and maintenance must not be carried out by children without supervision.
Keep the appliance and its power cord in a location that is not accessible to children under 8 years old.
Keep children away from the packaging material. It poses a risk of suffocation.
The appliance is operated with electric current. There is therefore a danger of electric shock:
Only plug the appliance into a correctly installed socket.
Only operate the appliance if the voltage stated on the rating plate matches the voltage of your socket.
Make sure that the power cord is not kinked or pinched and make sure that the power cord and the appliance do not come in contact with sources of heat (e.g. hobs, gas flames).
When unplugging the power plug from the socket, always unplug the power plug directly. Do not carry the appliance by the power cord.
Never touch the power plug with wet hands.
Do not insert any objects into the openings on the appliance.
As long as the power plug is plugged in, there is a voltage inside the appliance, even if the appliance is switched off.
After every use and in the event of danger or a defect, unplug the power plug from the socket immediately. For this reason, keep the socket into which the appliance’s power plug is plugged easily accessible at all times.
Unplug the appliance from the socket prior to cleaning or maintenance.
Never unscrew the appliance and do not make any technical modifications.
The sharp and rotating blade poses a serious risk of injury:
In the absence of supervision, disconnect the power plug prior to assembly, disassembly and cleaning.
Be very careful when filling, emptying and cleaning the blender bowl, and do not reach into the blades.
Poor hygiene is a health hazard:
Do not leave any food in the blender bowl if you are not using the appliance.
Clean the appliance and all accessories thoroughly prior to first use and immediately after every use.
A faulty appliance can cause damage and injuries:
Check the appliance for damage prior to each use. If you detect any transport damage, contact the dealer from whom you purchased the appliance immediately. Never use a faulty appliance or faulty accessories. Never operate an appliance or accessories that have been dropped.
The appliance needs to be repaired in the event of a fault or a damaged power cord. The appliance does not contain any parts that you are able to repair yourself.
Damage may occur if the appliance is handled incorrectly.
Place the appliance on a dry, level and non-slip surface.
Do not place the appliance on a hot surface or in the vicinity of strong sources of heat.
Do not let the power cord hang down.
When preparing food and drinks, liquid may spray or flow out and cause injury or property damage:
Always place the blender bowl on a level, non-slip surface. Never overfill the blender bowl. Do not open the lid closure during operation.
Never use the blender bowl to heat up food or drink in the microwave.
Explanation of symbols
Danger of death due to electric shock
Danger of cuts at the blades
Danger of scalding from hot liquids
Risk of property damage and damage to the appliance
Program functions
- On/Of
- Multi-function (pulse) – Post-mixing or pre-mixing of mixed products or individual ingredients
- Variable speed – Mixture with desired consistency from lumpy to liquid
- Cleaning – Cleaning of the blender bowl with water and detergent
- Ice cube crushing – Chopping ice cubes into ice pieces
- Cocktails – Liquid mixed drink composed of spirits, juices, syrup
- Smoothie – Creamy mixed drink made from fruits, herbs and dairy products
Overview
- Lid closure
- Blender lid
- Program symbols
- Selector switch / power button
- Power cord
- Blender base
- Blender bowl with blade
- Tamper
Operation
Putting the blender into operation
Prior to commissioning, you must unwind the power cord completely. You need to
press the power button to switch the blender on and off.
Filling with ingredients
To fill with ingredients, you need to place the blender bowl on a flat surface
and remove the lid or unscrew the lid closure. A measuring scale for the
filling quantity is attached to the blender bowl.
Observe the maximum mark. Do not overfill. For hot ingredients, observe a maximum filling quantity of 1,000 ml.
Putting the blender bowl on the base
Before you put on the blender bowl, you must first seal the bowl with the lid
and the lid closure and then place the bowl on the base so that the handle of
the bowl faces the front right.
The blender lid and the bowl
can only be attached as shown.
Preparing a beverage using the automatic program
To prepare the desired mixed drink, turn the selector switch to the left to
the corresponding program symbol and then press the power button. The mixed
drink is ready when the program symbol lights up continuously and a beep
sounds.
Interrupting the automatic program
You need to press the power button to stop the mixing process. A beep sounds.
You can continue the mixing process by pressing the power button again if the
desired consistency has not yet been achieved.
If the mixing process has been
interrupted, you can also remove the blender bowl from the base to refill
ingredients, press down with the tamper or check the consistency.
Using the multi-function program
To prepare any mixed drinks and liquid foods, turn the selector switch to the
right to the “Multifunction” program symbol and press and hold the power
button until the desired consistency of the product is achieved. The mixing
process stops if you let go of the power button.
Preparing products at your own mixing speed
To select a mixing speed, turn the selector switch to the right until the
blender starts up and reaches the desired speed. Once the desired consistency
of the product has been achieved, turn the selector switch back to the on/off
position.
The selected mixing speed is
shown by means of six dots. A flashing dot indicates the first of two possible
levels.
Switching off
To switch off the blender, turn the selector switch back to the on/off
position and press the power button.
Maintenance
Cleaning the blender bowl
To clean the blender bowl, fill the bowl with 400 ml of water, add some
detergent and start the cleaning program. Then rinse out the blender bowl
under running water.
Clean the blades carefully. Do not reach into them.
Cleaning the blender lid and tamper
You can clean the blender lid and the tamper under running water, with a damp,
lint-free cloth or in the dishwasher.
It is best to clean the blender
lid and the lid closure separately.
Cleaning the blender base
You can clean the blender base with a damp, lint-free cloth.
Prior to cleaning, unplug the power plug.
Technical data
Power supply: 220 – 240 V∼, 50/60 Hz
Energy consumption/Power: 1200 W
Capacity of the blender bowl: 1.4 l
Length of the power cord: 1 m
Dimensions of the blender base with bowl (L x W x H): 176 x 188 x 402 mm
Weight: approx. 4 kg
Do not dispose of in household waste.
The appliance complies with the directives for CE marking.
Fault
| Problem | Possible cause | Remedy |
|---|---|---|
| [he mixed product contains -nany ingredient pieces. | the power button was not | |
| pressed and held for longi- enough in the mull function program. | Press and |
hold the power button until the desired consistency is reached.
The mixing speed is too low or the mixing duration too short if you have
selected the mixing speed yourself.| If you have selected the mixing speed
yourself, turn the selecfor switch further to the right toincrease the mixing
speed, or ex-tend the mixing process until the desired consistency is reached.
The ingredients are not suitable f or the selected automatic program to be
used.| Finish mixing the mixed product with the multi-function program until
the desired consistency is achieved.
The appliance switches o— mmediotely.| The power button was not pressed and
held in the mul- ti-function program.| Press and hold the power button.
Liquid runs out of the blender bowl.| The blender lid, the lid closure or both
ports are not attached , correctly.| Attach the blender lid correctly and
seal it with the lid closure.
The seal of the blender lid is broken.| The seal must be exchanged by customer
service.
The blender bowl is overfilled.| Reduce the number of ingredient s or the
quantity.
A program symbol and the power button are flashing.| An automatic program has
been interrupted. The flashing indicates the interruption.| Press the power
button again to continue the automatic program.
All program symbols on the >lender base are flashing )nd three beeps sound.|
The blender bowl and the lid have been removed during operation.| Reattach the
blender bowl or lid and continue as desired.
The motor has overheated.| Put the selector switch in the on/ off position,
unplug the appliance and wait 30 minutes.
t is not possible to start he mixing process.| The blender bowl or the lid is
not attached correctly.| Place the blender bowl on the base with the handle
facing to the right or front or attach the lid correctly.
The blender has been stopped and the selector switch has been moved with the
lid open.| Put the selector switch in the on/ off position, press the power
button and then switch the appliance back on.
Customer service
Please contact our customer service should you encounter any problems with
your blender.
Detailed information on service, repairs, warranty and product registration
can be found at www.zwilling.com/service.
Disposal
With regard to disposal, please return your old appliance to a collection point for electrical appliances
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>