dahua DH-AX30 Wireless Router User Manual

dahua DH-AX30 Wireless Router User Manual

Foreword

This manual introduces the installation, functions and operations of the DH- AX15M device (hereinafter referred to as “the Device”). Read carefully before using the device, and keep the manual safe for future reference. Safety Instructions
The following signal words might appear in the manual.

in death or serious injury.
| Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
| Indicates a potential risk which, if not avoided, could result in property damage, data loss, reductions in performance, or unpredictable

results.

| P rovides methods to help you solve a problem or save time.
 | P rovides additional information as a supplement to the text.

About the Manual

• The manual is for reference Slight differences might be found between the manual and the product.
• We are not liable for losses incurred due to operating the product in ways that are not in compliance with the
• The manual will be updated according to the latest laws and regulations of related For detailed information, see the paper user’s manual, use our CD-ROM, scan the QR code or visit our official website. The manual is for reference only. Slight differences might be found between the electronic version and the paper version.
• There might be errors in the print or deviations in the description of the functions, operations and technical If there is any doubt or dispute, we reserve the right of final explanation.
• Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be

Important Safeguards and Warnings

This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, and comply with the guidelines when using it.

Transport the device under allowed humidity and temperature Refer to the technical parameters for requirements on the transporting temperature and humidity of the device.

Storage Requirements

• Store the device under allowed humidity and temperature Refer to the technical parameters for requirements on the storing temperature and humidity of the device.

Installation Requirements

• Do not place the device in a place exposed to sunlight or near heat
• Put the device in a well-ventilated place, and do not block itsventilation.
• Use an adapter or cabinet power supply provided by the
• Do not connect the device to two or more kinds of power supplies, to avoid damage to the device.
• To ensure heat dissipation, the gap between the device and the surrounding area should not be less than 10 cm on the sides and 10 cm on top of the
• When installing the device, make sure that the power plug and appliance coupler can be easily reached to cut off
• Voltage stabilizer and lightning surge protector are optional depending on the actual power supply on site and the ambient

Operation Requirements

• Do not disassemble the device without professional
• Operate the device within the rated range of power input and
• Make sure that the power supply is correct before
• Make sure the device is powered off before disassembling wires to avoid personal
• Do not unplug the power cord on the side of the device while the adapter is powered on
• Use the device under allowed humidity and temperature
• Operating temperature: 0°C–40 °C (14 °F–104 °F)ns.
• This is a class A product. In a domestic environment this may cause radio interference in which case you may be required to take adequate
• Do not drop or splash liquid onto the device, and make sure that there

Indicator

system booting

Red flashes

(slow)

| The router is pairing with the sub -route; WPS processing

in 120s

Red flashes (fast)| System upgrade
Off| The router is powered off or the light is manually turned off

Connection Diagram

Adding Devices Prerequisites

Make sure that the device is connected with power and modem. After thedevice is powered on, wait for 2 minutes, and then add devices.

Procedure

Step 1

On the Status page, tap Add Device or on the right-upper corner

Figure 3-3 Preparations for adding device

Step 2     Scan the QR code on the device, or tap Select Type of the device, and then enter the SN.
Step 3     Go to the Wi-Fi settings on your system settings, connect the router
SSID, and then tap Next.
Step 4
Step 5 Configure the login password of the device, and then tap Next. Configure the networking method of the device, and then tap Next.
Step 1 On the Status page, tap Add Device or on the right-upper corner.
Wait until the screen prompts Connect to Internet , and then tap Next.
Configure the time zone and DST of the device, configure the device SSID, and then tap Next to finish the configuration.

Figure 3-5 Configure time zone and Wi-Fi network

Procedure

Figure 3-7 Network settings
Step 8     Enter the WLAN Setting page, set Wi-Fi name, password and power, and then click Save.
Figure 3-8 WLAN settings
Step 1 The end device connects to the router through wired and wireless connection. Enter the device domain name(   ) or device IP( default IP 192.168.10.110 ) to log in to the device to configure settings.
step 2     Click OK.
Step 3  Select the I have read and agree to the terms of the Software License Agreement and Privacy Policy checkbox, and then click OK.
Step 4 For the first-time login,you need to set the login password,and then click NEXT.

Step 5     Enter the login password, and then enter the web page.

Step 6 ____         For the first-time login,the device will pop up a setup wizard.
Step 7     WAN settings : You can change the networking method (default DHCP), click the icons to change, and then click Next.

Figure 3-6 WAN settings

Figure 3-5 Configure time zone and Wi-Fi network

• If you can access Internet without any settings on your bandwidth, select DHCP as the networking
• If your bandwidth cannot obtain IP address automatically, contact network administrator or bandwidth service provider, select Static IP as the networking method, and then enter related information as
• If you need to enter the account and password to access

Internet, select PPPoE as the networking method, and then enter bandwidth account and bandwidth password.

Figure 3-8 WLAN settings

Downloading App

Scan the QR code to download the WiLynk app

Read More About This Manual & Download PDF:

References

• Dahua Technology - World Leading Video-Centric AIoT Solution & Service Provider

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>