HAVIT Lighting HV3282T-SS316 Mood Plus Ridge Step Light Installation Guide
- June 12, 2024
- Havit Lighting
Table of Contents
HAVIT Lighting HV3282T-SS316 Mood Plus Ridge Step Light Installation Guide
Mood + Ridge Step Light Installation Instructions
Product Specifications
Model No.| HV3282T-SS316| HV3282T-BLK| HV3282T-WHT| HV3282T-BRZ| HV3282T-GPH|
HV3283T-SS316| HV3283T-BLK| HV3283T-WHT| HV3283T-BRZ| HV3283T-GPH
Name| Mood| Ridge
Material| 316 Stainless Steel| Bronze| Solid Brass| 316 Stainless Steel|
Bronze| Solid Brass
Colour| Stainless Steel| Black| White| Bronze| Graphite| Stainless Steel|
Black| White| Bronze| Graphite
IP Rating| IP54
Input Voltage| 12v DC
Protection Class| (Low Voltage)
Lamp Base| Built in LED
Lamp Wattage| 1x 6w| 1x 6w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k| TRI Colour – 3000k, 4000k,
5500k
Lumens| 460lm, 490lm, 520lm| 460lm, 490lm, 520lm
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 3 Years Replacement*
HV3282 Dimensions
HV3283 Dimensions
Mounting Base Diagram
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- When installing brass fittings, gloves must be worn to avoid any oils transferring to fitting.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
- All o-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Steps for Installation
- Make sure that the electrical circuit is free of voltage (master switch off )
- Remove base plate from fitting by loosening allen screws on side of fitting and put fitting aside.
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable – If more than one fitting installed, wiring must be done in parallel.
- Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Install Base plate in desired location using apprpriate screws.
- Silicone cable entry and around screws to avoid water penetration.
- Fitting is preset to 3000k, To change slide switch located on top of PCB to desired colour temperature.
- Reattach fitting to base plate making sure allen screws are tight to avoid water penetration
- Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electriccircuit.
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: [email protected]
Web: www.havit.com.au
*Warranty Terms & Conditions
https://havit.com.au/pages/warranty-terms-and-conditions
Additional
Information
**https://havit.com.au/