tracer T5 TWS BT Wireless Headset Instruction Manual

tracer T5 TWS BT Wireless Headset

Product Information

• Product Name: Tracer T5 TWS BT Wireless Headset

• Bluetooth Version: 5.3

• Range: 10 meters

• Charging Time: Approximately 1.5 hours

• Battery Capacity: Headset – Not specified,
  Charging Case – Not specified

• Operating Frequency: 2.4 GHz

• Impedance: Not specified

• Standby Time: Not specified

Product Usage Instructions

Product Parts

1. Headphone charging port
2. Earphone dust screen
3. Multi-function touch point
4. Microphone
5. Headphone indicator
6. LED power display
7. Type-C Charging interface

Packaging Accessories

1. Charging compartment
2. Earphone Charging Cable
3. User manual

Instructions for Headset Touch Operation

Left Ear Touch:

• x1: Long press for binaural sharing
• x2: Long press for mobile phone status, ON not connected for 5 seconds, Headphone off status for long press of 3 seconds
• x3: Restore factory settings when headphone is off
• x4: DUT test when headphone is off
• x5: Headphone off status

Right Ear Touch:

• x1: Long press
• x2: Long press

Earphone Connection Instructions

1. Pairing:
   • a. Take out the headset from the charging bin and it will turn on automatically
   • b. The headset changes from red to blue alternately when turned on; The main ear blue light flashes once every 3 seconds, and the auxiliary ear light does not light up. Voice prompt “Connect, pairing successful”
2. Connecting:
   • a. Connect with a device: Turn on the phone or other mobile device, search for Tracer T5, and touch “Connect”
   • b. The headphones can be connected independently. After the connection is completed, the system will display the message “disconnect”
3. Turning Off:
   • a. Put it into the charging bin and turn it off
   • b. If the headphones are not used and not connected with the phone, press and hold the multi-function button for about 5 seconds to turn them off
   • c. If the headphones are not connected for 3 minutes, they will enter standby mode and turn off automatically. When the voltage drops below 3.1V, the headphones will turn off automatically with a voice prompt

Charging Instructions

Charging the Headphones:

During charging, the red indicator light stays on. It turns off after the battery is fully charged. The display on the charging case shows the current battery level.

Charging Case:

The charging case supports charging the headphones. The red indicator light stays on during charging.

Basic Information

• Product Name: Tracer T5
• Bluetooth Version: 5.3
• Range: 10 meters
• Charging Time: Approximately 1.5 hours
• Power Input: 5V, 0.23A
• Operating Frequency: 2.4 GHz
• Impedance: Not specified
• Standby Time: Not specified
• Important Information
• No information provided.
• Safety Instructions
• No information provided.

Product parts 

1. Headphone charging port
2. Earphone dust screen
3. Multi-function touch point
4. Microphone
5. Headphone indicator
6. LED power display
7. Type-C Charging interface

Packaging accessories

1. Charging compartment
2. Earphone
3. Charging Cable
4. User manual

Instructions for headset touch operation

Earphone connection instructions

Pair

• Take out the headset from the charging bin and turn it on automatically
• The headset changes from red to blue alternately when turned on; The main ear blue light flashes once every 3 seconds, and the auxiliary ear light does not light up.Voice prompt Connect, pairing successful
• For the second use, open the charging cover,The headset is automatically turned on and paired

Connect

• Device connection: open the mobile phone or other device, search for „Tracer T5”, and click Connect.
• The left and right earphones can be connected separately. If the connection is disconnected, the voice prompts Disconnect.

Shutdown

• Put it into the charging bin and turn it off.
• If it does not work for 3 minutes, it will sleep and shut down. When the voltage is lower than 3.1V, the headset automatically turns off
• Mobile phone not connected, Press and hold the multifunction key for about 5 seconds voice prompt Power off

Charging instructions

Headphone charging

• When the voltage is lower than 3.2V, the headset prompts “Battery low” (Prompt every 3 minutes)
• The red light of earplug charging is always on, and it goes out when it is full. The digital display of the charging chamber shows the current power, and it is off when fully charged

Charging chamber

When the charging bin is charged with a charging cable, the charging bin digital displays the current power and jumps the current value, Display 100 power when fully charged and always on

The basic parameters

Matters needing attention

• Please make sure the product is fully charged before the fi rst use; Or charge it fi rst.
• Please use a brand charger or computer USB to charge the headset (note: 5V-1A charger).
• Stay away from WIFI and routers and other high frequency transmitting devices,which may affect the signal reception of the unit and cause the phenomenon of sound blocking and disconnection.
• Please use the product in an effective environment (10 m) and there should be no physical barriers (such as walls, etc.) between the BT device and the headset.
• Please refer to Item 4 when there is no sound on one side of the earphone and the pairing of two ears is not successful (headset connection instructions) pair and connect the headset again, and the product will work normally after reconnection!

Use safety instructions

To avoid hearing damage, keep the volume at a moderate level. Avoid listening to music at high volume for a long time, as this may cause permanent damage to your hearing or deafness. Please do not use Tracer T5 when driving, riding bicycle, crossing the road, etc. where your concentration is required. Note: If you use headset while watching a video, the audio and video may be slightly out of sync. After charging is complete, please unplug the charging cable from the product to avoid leaving the product in a charging state for along time. Do not use a charger that exceeds the rated voltage and current of the headset (5V/1A) to charge the headset. If the output voltage and current of the charger exceed the specifie standards,this will cause serious damage to the product and the product warranty will be in validated at the same time.

• Maximum Transmitter Power (E.I.R.P) ≤20 dBm
• The range of which the device operates: 2400 MHz – 2483,5 MHz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>