Bosch SMS4ETW02E Built In Dishwasher User Guide

Bosch SMS4ETW02E Built In Dishwasher

Product Information

The product is a dishwasher that offers various features and settings for efficient dishwashing. It can be connected to a mobile device using the Home Connect app, allowing users to control and change settings conveniently. The dishwasher has an adjustable water hardness system and provides an overview of water hardness values for different settings. It also has compartments for adding special salt, rinse aid, and detergent. The dishwasher offers different programmes with varying durations, energy consumption, and water usage. It also has a Machine Care programme for maintenance and a Favourite programme for quick use. The dishwasher is designed to clean tableware that is suitable for dishwashers, with removable filters for easy cleaning.

Product Usage Instructions

1. Before using the dishwasher for the first time, read the instruction manual and safety information.
2. To set up Home Connect:
   • Install the Home Connect app on your mobile device and follow the instructions.
   • Scan the QR code with the Home Connect app.
3. To adjust water hardness settings:
   • Refer to the table in the instruction manual for country-specific units.
   • Select the appropriate setting value based on water hardness range.
4. To add special salt:
   • Unscrew the lid of the special salt dispenser.
   • If it’s the initial start-up, fill the dispenser with water.
   • Add the special salt to the dispenser, ensuring no detergent is added.
5. To add rinse aid:
   • Press the catch on the lid of the rinse aid dispenser and lift.
   • Add rinse aid up to the max mark.
6. To set the water softening system:
   • Press the appropriate button to open the basic settings.
   • Press repeatedly until the desired water hardness is displayed.
   • Press and hold the save button for 3 seconds to save the settings.
7. To add detergent:
   • Add the detergent to the dry detergent dispenser according to the recommended ml measurements.
8. To use the dishwasher:
   • Load the tableware that is suitable for dishwashers, removing large food remnants.
   • Switch on the appliance.
   • Select the desired programme based on duration and cleaning needs.
   • Start the programme.
   • Remove the tableware at the end of the programme.
   • To cancel a programme, press and hold the cancel button for approximately 4 seconds. The programme will be cancelled and end after about 1 minute.
9. To clean filters:
   • After each wash, check the filters for debris and clean if necessary. Refer to the instruction manual for detailed instructions on cleaning filters.

Setting up Home Connect

• Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.
  1. Install the Home Connect app on your mobile device and follow the instructions.
  2. Scan the QR code with the Home Connect app.

Overview of water hardness settings
You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual.

Setting the water softening system

1. Press ⁠.
2. To open the basic settings, press setup 3 sec. for 3 seconds.
   • The display shows Hxx.
   • The display shows set ⁠.
3. Press repeatedly until the right water hardness has been set.
4. To save the settings, press setup 3 sec for 3 seconds.

Programmes

The programme data has been measured in the laboratory according to European standard EN 60436. The consumption figures depend on the programme and additional function selected. The running time will change if the rinse aid system is switched off or rinse aid needs to be added.

Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts.

1. Unscrew the lid of the dispenser for special salt and remove.
2. On initial start-up: Fill the dispenser right up with water.
3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
4. Place the lid back on the dispenser and turn to close.

Adding rinse aid

1. Press the catch on the lid of the dispenser for rinse aid 1 and lift 2
2. Add rinse aid up to the max mark.
3. Close the lid of the dispenser for rinse aid.
   • The lid clicks into position ⁠.

Adding detergent

1. Add the detergent to the dry detergent dispenser.
2. Close the lid of the detergent dispenser.
   • The lid clicks into position.

How to use your appliance

1. Load the tableware. Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.
2. Add detergent.
3. Switch on the appliance ⁠.
4. Select the programme.
5. Start the programme ⁠start .
6. Remove the tableware at the end of the programme.
7. To cancel the programme, press reset  4 sec. for approx. 4 seconds. The programme is cancelled and ends after approx. 1 minute.

Cleaning filters

1. After each wash check the filters for residue.
2. Turn the coarse filter anticlockwise  1 and remove the filter system 2 ⁠.
3. Pull down the micro filter to remove.
4. Press the locking catches 1 together and lift the coarse filter out 2  ⁠.
5. Clean the filter elements under running water.
6. Re-assemble the filter system.
7. Insert the filter system into the appliance and turn the coarse filter clockwise.
   Make sure that the arrow markings match up.

Cleaning spray arms

1. Unscrew the upper spray arm and pull down to remove ⁠.
2. Pull up the lower spray arm 1 to remove 2 .
3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
4. Insert the lower spray arm.
   • The spray arm clicks into position.
5. Insert the upper spray arm and screw it firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.
2. Remove the filter system.
3. Scoop out any water.
4. Prise off the pump cover using a spoon and grip it by the crosspiece.
5. Lift the pump cover inwards at an angle and remove.
6. Remove any remnants of food and foreign bodies in the area of the impeller.
7.  Insert the pump cover 1 and press down 2  ⁠.
   • The pump cover clicks into position.
8. Install the filter system.

Troubleshooting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>