Top Victory Electronics PN7462 Reader Module Instruction Manual

: June 4, 2024
: Top Victory Electronics

Table of Contents

- Top Victory Electronics PN7462 Reader Module
- Overview
  - Contact and Contactless Features
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Overview

The reader module used NXP PN7462 controller is a highly integrated ISO/IEC7816 interface and transceiver module for contactless reader/writer communication at 13.56 MHz. A dedicated Flash code is implemented to handle different RF protocols by an integrated microcontroller. The system host controller communicates with the module by using the USB link. The protocol between the host controller and the module, on top of this physical link is the CCID protocol

Product Photo as below:

Contact and Contactless Features

Integrated contact interface frontend 
- Class A, B, and C cards can work on 1.8 V, 3 V, and 5 V supply
- Specific ISO UART, variable baud rate through frequency or division ratio programming, error management at character level for T = 0, and extra guard time register
- DC-to-DC converter for class A support starting at 3 V, and class B support starting at 2.7 V.
- Thermal and short-circuit protection on contact cards
- Automatic activation and deactivation sequence, initiated by software or by hardware in case of short-circuit, card removal, overheating, and VDD or VDD dropout
- Enhanced ESD protection (> 8 kV)
- ISO/IEC 7816 compliant
- EMVCo 4.3 compliant
- Synchronous card support
Integrated contactless interface frontend 
- High RF output power frontend IC for transfer speed up to 848 kbit/s
- NFC IP1 and NFC IP2 support Full NFC tag support (type 1, type 2, type 3, type 4A, type 4B and type 5)
- P2P active and passive, target and initiator
- Card emulation ISO14443 type A
- ISO/IEC 14443 type A and type B
- MIFARE products using Crypto1
- ISO/IEC 15693, and ISO/IEC 18000-3 mode 3
- Low power card detection
- Dynamic Power Control (DPC) support
- Compliance with EMV contactless protocol specification
- Compliance with NFC standards
Support NFC Mode
- ISO/IEC 7816
- ISO/IEC 14443-A and B, MIFARE
- JIS X 6319-4 (comparable with FeliCa scheme)
- ISO/IEC 15693, ICODE, ISO/IEC 18000-3 mode 3
- NFC protocols – tag reader/writer, P2P
- ISO/IEC 14443- type A card emulation
- EMVCo compliance

Caution

Please keep this product and accessory accessories to a child’s reach.
Do not spill water or other liquids onto this product, otherwise it may cause damage.
Please do not place this product near the source of heat or place it in direct sunlight. Otherwise, it may cause deformation or malfunction.
Please let this product be flammable or fire such as lighted candles.
Please do not repair this product by yourself, only professionals can repair it.

General Specifications

Bus Powered – +5V +/- 5%, 500mA
Average Power Consumption
Standby Mode: 0.12Watt
Active/Read Card Mode:

ISO/IEC7816 => Varied by Different Card Type. NFC => 0.24 Watt

Operational environment
- Operating Temperature: -10°~60°
- Operating Humidity: 10%~90%
- Storage Temperature: -20°~70°
- Storage Humidity: 10%~90%

Modulation Type: ASK
Operating Frequency: 13.56MHz

Note: If the design and specifications are changed, no notice shall be given.

This device complies with Part 15 of the FCC / ISED’s license-exempt RSSs Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

FCC/ISED/CE-RED Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:
The product comply with the FCC/ISED/CE-RED portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:

KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules
This module has been tested for compliance to FCC Part 15

Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification.

Limited module procedures
Not applicable.

Trace antenna designs
Not applicable.

RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules.

Antennas
The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module.

Antenna Type Loop Antenna
Antenna connector N/A

Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC ID: ARS-PN7462”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.

Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification.

Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end- product for any additional compliance requirements required with this module installed.

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Industry Canada statement:
This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

FOR PORTABLE DEVICE USAGE ( <20m from body/SAR needed)

Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

This device is intended only for OEM integrators under the following conditions: (For module device use)

The transmitter module may not be co-located with any other transmitter or antenna.

As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.

End Product Labeling FOR PORTABLE DEVICE USAGE ( <20m from body/SAR needed)

The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: “Contains IC: 9190A-PN7462”.

Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Europe EU Declaration of Conformity
This device complies with the essential requirements of the Radio Equipment
Directive (2014/53/EU) and Radio Equipment Regulations 2017. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the Radio Equipment Directive.