DIGITAL YACHT AIS100USB AIS Receiver with USB User Guide

AIS100USB AIS Receiver with USB
User Guide

AIS100USB AIS Receiver with USB

AIS100USB Quick Start Guide

Installation Step 5

• The easiest was to install the drivers on Windows 7/8/10 is to make sure the PC is connected to the internet and to plug the AIS100USB in. The “Found New Hardware Wizard” will be triggered and Windows will search online for the latest driver.
• If you do not have an internet connection or you are using Windows XP then you may need to manually install the driver which is located in the “AIS100+iAIS+uAIS+AISNet USB Driver” folder on the supplied “Software and Drivers” CD.
• Windows will create a “virtual” COM port for the AIS100USB and you will need to go to the Windows Device Manager program and look in the “LPT&COM Ports” section to find out what COM port number has been allocated to the  AIS100USB. Make a note of this number as you will have to enter this COM port number in the PC Navigation software, so that it knows which port the AIS is connected to – consult the instruction manual supplied with your PC  Software to understand how this is configured.
• Apply power to the AIS100USB Receiver and verify that after a couple of seconds the Green “Status” LED lights. This indicates that the unit is powered up correctly and the drivers are installed and working correctly.
• The “Status” LED will flicker every time that valid data from an AIS target is received. Depending upon the number of vessels, fitted with AIS transponders, sailing within VHF range of your vessel, the frequency of flickering maybe constant or as little as once every 30 seconds.
• Installation is now completed

The AIS100USB is also compatible with Mac OS X and all LINUX Kernels since V2.4.20. For more information on using the AIS100USB with non-Windows operating systems, please check the Digital Yacht website www.digitalyacht.co.uk

Installation & Quick Start Guide AIS100USB AIS Receiver

Introduction

Congratulations on the purchase of your AIS100USB AIS Receiver. It is recommended that your receiver is installed by a professional installer.
Before operating the unit you should familiarise yourself with this Quick Start Guide and the user manuals for any equipment you wish to connect it to.

Before you start

You will need the following items and tools to complete the installation:

• The AIS100USB Receiver
• Dedicated AIS/VHF antenna or existing VHF antenna and splitter
• M3 or M4 screws or other fixings appropriate to the mounting location.

To display the AIS targets and data you will need:

• Suitable PC Navigation software running on a PC with Microsoft Windows XP® /Windows 2000 ® or Windows Vista ® /Windows 7 ® with a free USB port

Installation

Before starting installation select a suitable location for the AIS Receiver. The unit is water resistant; however it should be installed below deck in a dry location. When locating the unit you should consider:

• Routing of power and antenna cables to the unit.
• Provision of sufficient space behind the unit for cable connections.
• Routing of USB data connections to PC.
• Maintaining the compass safe distance of 0.5m.

Installation Step 1

• Run the VHF co-axial cables to the AIS Receiver and terminate with the correct connectors:
• The VHF antenna cable should be terminated in a BNC connector (Bayonet)
• Run the interfacing cables from the AIS Receiver to the PC’s USB port
• Do not make any connections yet

Do not plug in the USB lead of the AIS100USB into a PC until you have inserted the supplied “Digital Yacht Software and Drivers CD” in the CD drive of your PC.
Installation Step 2

• Fix the AIS 100 to a bulkhead or flat surface using suitable fixings (not supplied). Note that the unit may be installed in any orientation. The drawing on the following page shows an AIS100 but the drilling and fixing details are identical  for an AIS100USB.

Fixing location drawing

• Once the unit is secured, connect the AIS/VHF antenna. Ensure the connection is fully made; should feel a slight click as the BNC locks.

Installation Step 3

• The AIS100USB is powered from the USB port of the computer you are connecting it to, so there is no need to provide a power feed from the boat’s electrical system.
• The Green Status LED on the unit will not illuminate when you plug it in to the PC unless the drivers are installed.

Installation Step 4

• The AIS100USB Receiver can be connected to a PC via its USB lead. If you wish to extend the USB cable from the AIS100USB to the PC, you can use an unpowered USB extension cable (maximum of one 3m extension) or a more  expensive powered USB extension cable (maximum of one 5m extension) which are available from good electronics shops.

QUICK START AIS100USB V1.03

References

• Digital Yacht - Light years ahead in marine electronics technology.
• Digital Yacht - Light years ahead in marine electronics technology.
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>