KARCHER Conditioner SP 16.000 Dirt Dirt submersible drainage pump flow rate Instruction Manual

SP 16.000 Dirt
SP 22.000 Dirt

Register your product
www.kaercher.com/welcome

Conditioner SP 16.000 Dirt Dirt submersible drainage pump flow rate

|
---|---

General notes

Read these original operating instructions and the enclosed safety instruc- tions before using the device for the first time. Proceed accordingly.
Keep both books for future reference or for future owners.

Intended use

Only use the device in private households.
Intended use:

• Removal of water from building sections in the event of flooding
• Transferring and pumping water from containers
• Water removal from wells and shafts
• Pumping fresh water out of boats and yachts For notes on functional principle, see chapter Operation.

Permissible feed fluids
DANGER
Danger of death and risk of damage when pumping explosive, flammable or unsuitable substances! Flammable or explosive substances may ignite or explode. Unsuitable substances can damage the pump.
Do  not pump explosive, flammable or corrosive liquids or gases (e.g. fuels, petroleum, nitro thinner) and do not pump fats, oils, salt water or waste water from sanitary facilities or water that has a lower flowing ability than clean water.
Permissible feed fluids:

• Fresh water up to a certain degree of soiling.
  SP 16000 Dirt:
  Water with a degree of soiling up to grain size 20 mm
  SP 22000 Dirt:
  Water with a degree of soiling up to grain size 30 mm

• Swimming pool water with intended dosage of additives.

• Washing lye, e.g. from leaking washing machines.
  Then rinse and clean the pump with clear fresh water, see chapter Rinsing and cleaning.

• The temperature of the pumped liquids must lie between 5°C and 35°C.

Improper use
ATTENTION
Risk of damage due to frost!
Operation during frost may damage the device.
An incompletely emptied device can be damaged by frost.
Do not operate the device during frost.
Protect the device from frost.

ATTENTION
Risk of damage during continuous operation!
The device is not suitable for continuous operation.
Do not operate the device continuously for long periods (e.g. continuous circulation operation in ponds) or as a stationary installation (e.g. as a water lifting system, fountain pump).
Note
The manufacturer accepts no liability for possible damage caused by improper use or incorrect operation.

Hazard levels
DANGER

• Indication of an imminent threat of danger that will lead to severe injuries or even death.

WARNING

• Indication of a potentially dangerous situation that may lead to severe injuries or even death.

CAUTION

• Indication of a potentially dangerous situation that may lead to minor injuries.

ATTENTION

• Indication of a potentially dangerous situation that may lead to damage to property.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish.

Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.com/REACH

Accessories and spare parts

Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery
The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Warranty

The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)

Device description

See graphics page for illustrations Illustration A

1. Carrying handle
2. Power supply cable with plug
3. Automatic venting device
4. Quick-Connect
5. Pump connecting piece G 1 ½ (1”, 1 ¼” and 1 ½” hose connection and G 1 ½ thread )
6. Connection nozzle (G 1 ½ thread)
7. Lock (float switch)
8. Height adjustment (float switch)
9. Float switch
10. *Pump connecting piece G 1 ( ¾″ and 1″ hose connection and G 1 thread)
11. • Check valve
12. G 1 Threaded connection (SP 16000 Dirt)
13. Pre-filter (SP 22000 Dirt)

*Not included in the scope of delivery.

Initial startup

DANGER
Risk of electric shock and risk of injury!
The device contains electrical and mechanical components.
Always disconnect the device from the power supply before assembling, disassembling or cleaning.
Note The shorter the hose length and larger the hose diameter, the higher the delivery rate.
To avoid clogging the pump, use a pre-filter for hose diameters smaller than 1¼″.

• SP 16000 Dirt Special accessories
• SP 22000 Dirt Integrated in the foot The pump connection is equipped with a plug system (Quick-Connect).

The connection nozzle with pump connecting piece G 1 ½ and G 1 threaded connection are supplied unassembled with the device.

Note
Hoses with a diameter of 1″, 1 ¼″ and 1 ½″ can be connected to the pump connecting piece G 1 ½. A sufficiently large hose diameter must be selected and the G 1 ½ pump connecting piece must be shortened at the grooves so that the required particle size can be pumped. A large hose diameter is also recommended for smaller particle sizes to allow a high flow volume.

Connecting a hose to the pump when using a 1″,1 ¼″ or 1 ½″ hose:

1. Screw the G 1 ½ pump connecting piece onto the connection nozzle.
   Illustration B

2. Push the hose clamp onto the hose.

3. Push the hose onto the G 1 ½ pump connecting piece and fasten it with a hose clamp.

4. Push the connection nozzle into the Quick-Connect.

Illustration C
Connecting a hose to the pump when using a ¾″ or 1″ hose (SP 16000 Dirt):

1. Screw the G 1 threaded connection onto the connection nozzle.

2. Fit the special accessory G 1 pump connecting piece(6.997-359.0 pump connecting piece G 1 (33.3 mm) incl. check valve – not included in the scope of delivery) onto the G 1 threaded connection:
   a Place the check valve on the G 1 threaded connection so that the lettering “UP” is legible.
   b Screw the pump connecting piece G 1 onto the G 1 threaded connection.

3. Push the hose clamp onto the hose.

4. Push the hose onto the pump connecting piece G 1 and fasten it with a hose clamp.

5. Push the connection nozzle into the Quick-Connect.

Illustration C
Erecting/immersing the pump:

1. Fit the height adjustment of the float switch into the lock.
   Illustration D

2. Place the pump securely on solid ground in the pumped liquid or immerse it via a rope attached to the carrying handle.

Note
The suction area must not be blocked by soiling. If the ground is muddy, place the pump on a brick or similar.
Make sure that the pump stands level. Do not carry the pump using the cable or hose.

Operation

DANGER
Danger of death from electric shock.
Danger of death from electric shock if live parts are touched.
During operation, do not touch the rope attached to the carrying handle or any objects that are in contact with the pumped liquid (e.g. pipelines protruding into the pumped liquid, railings) and do not reach into the pumped liquid.

Automatic venting device

1. If the fluid level is low, any sucked-in air, or air present in the pump, may escape via the automatic venting device. Fluid can also leak along with air. If the pump has problems with suction when the fluid level is low, unplug and plug in the mains plug repeatedly to assist the suction process. Illustration E

Automatic mode

1. Adjust the float switch via the height adjustment and the cable length.
   Note If the pump is operated unattended, always set the float switch to the top position to ensure reliable pump switch-off. Illustration F Note When the pump is set to the lowermost position, set the cable length between the float switch and the lock to 2.5 cm, see marking on the cable. Illustration G

2. Plug the mains plug into the socket.
   Note In automatic mode, the float switch controls the pumping process automatically. The pump switches on as soon as the float switch reaches the switch-on height caused by the rising fluid level. The pump switches off as soon as the float switch reaches the switch-off height caused by the sinking fluid level. The float switch must be able to move freely. The cable length between the float switch and the locking device must be at least 2.5 cm.

Switch-on height / switch-off height (float switch in lowest position):

Switch-on height / switch-off height (float switch in uppermost position):

• The switching heights vary depending on the position of the float switch and the cable length between the float switch and the lock. We recommend retaining the set cable length.

Manual mode
Note
In manual mode, the pump stays switched on. The fluid level must be at least 60 mm (SP 16000 Dirt) or 50 mm (SP 22000 Dirt) for the pump to prime itself in manual mode. The pump can pump up to a residual fluid height of 25 mm (SP 16000 Dirt) or 35 mm (SP 22000 Dirt). The specified residual fluid height is only achieved in manual mode.
The float switch must be able to move freely.

1. Fasten the float switch in the lock pointing upwards.
   Illustration H
   ATTENTION
   Risk of damage from dry running!
   Dry running leads to increased wear on the pump.
   Do not leave the pump unattended in manual operation.
   In case of dry running, immediately pull the mains plug out of the socket.

2. Plug the mains plug into a mains socket.

Finishing operation

1. Pull the mains plug out of the socket.
   The device stops.
   ATTENTION
   Risk of damage!
   Risk of damage due to dried soiling or additives.
   Rinse and clean the device immediately after each use.

2. If dirty liquids or liquids with additives have been pumped, rinse and clean the device immediately after finishing operation, see chapter Rinsing and cleaning.

3. Drain the device and accessories and let them dry.

Care and maintenance

DANGER
Risk of electric shock and risk of injury!
The device contains electrical and mechanical components.
Cleaning and user maintenance may not be carried out by children.

Rinsing and cleaning
ATTENTION
Risk of damage!
Risk of damage due to dried soiling or additives.
Rinse and clean the device immediately after each use.

1. If dirty liquids or liquids with additives have been pumped, the device must be rinsed afterwards: Use the device to pump clear fresh water without additives until all soiling or additives have been flushed out of the device.
   DANGER
   Risk of electric shock and risk of injury!
   The device contains electrical and mechanical components.
   Always disconnect the device from the power supply before assembling, disassembling or cleaning.

2. Pull the mains plug out of the socket.

3. Press the Quick-Connect button and remove the connection nozzle.
   Illustration C

4. Where necessary, remove residue from the hose and on Quick-Connect.

5. Clean the outside of the device with a soft, clean cloth and clear fresh water.

6. Drain the device and accessories and let them dry.

Service
The device is maintenance-free.

Transport

Manual transport
CAUTION
Risk of injury from tripping!
There is a risk of injury from tripping on loose cables and hoses.
Be careful of cables and hoses when moving the device.

1. Lift and carry the device by the carrying handle.
   Transport in vehicles
   WARNING
   Risk of injury, risk of damage!
   Note the weight of the device during transport.
   Store or secure the device in accordance with applicable guidelines so that it cannot slip or be thrown around during transport.

2. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respectively applicable guidelines.

Storage

ATTENTION
Risk of damage due to frost!
An incompletely emptied device can be damaged by frost.
Completely empty the device and accessories before storing them.
Protect the device from frost.
Store the device in a frost-free place and not outdoors.
CAUTION
Risk of injury and damage!
The device may tip over on sloping surfaces.
Be aware of the weight of the device during storage.

1. Completely empty the pump and accessories.
2.  Allow the pump and accessories to dry out.
3. Store the pump in a frost-protected place.

Troubleshooting guide

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

mains plug out of the socket and
plug it in again several times, until the fluid is drawn in.
The suction area is clogged.| 1. Pull the mains plug out of the socket.
2. Clean the suction area.
The fluid level is too low in manual operation.| 1. Immerse the pump deeper into the feed fluid if possible, see chapter Operation.
The pump does not start up, or stops suddenly during operation| The power supply is disconnected.| 1. Check the fuses and the electrical connections.
The thermal protection switch has switched off the pump because of over- heating.| 1. Pull the mains plug out of the socket.
2. Allow the pump to cool down.
3. Remove any dirt particles in the suction area.
4. Clean the suction area.
5. Prevent the pump from running dry.
Dirt particles block the suction area.| 1. Pull the mains plug out of the socket.
2. Clean the suction area.
The pumping capacity decreases| The suction area is clogged.| 1. Pull the mains plug out of the socket.
2. Clean the suction area.
The delivery rate is too low| The maximum delivery head is exceed- ed.
The hose diameter and the hose length have been selected incorrectly.| 1. Observe the maximum delivery head, see chapter Technical data.
2. If necessary, select a greater hose diameter or a shorter hose length, see chapter Optimising the flow rate.
Quick-Connect cannot be opened or closed| The push-fit system is dirty.| 1. Remove the clip.
2. Clean the clip.
3. Install the clip.

Technical data

Device performance data| | SP
16.000
Dirt| SP
22.000
Dirt
---|---|---|---
Mains voltage| V| 230-240| 230-240
Power frequency| Hz| 50| 50
Nominal power| W| 550| 750
Maximum flow rate| l/h| 16| 22
Pressure (max.)| MPa
(bar)| 0,08
(0,8)| 0,08
(0,8)
Delivery height (max.)| m| 8| 8
Immersion depth (max.)| m| 7| 7
Perm. temp. feed fluid| °C| 5…35| 5…35
Particle size (max.) of permissible feed fluids| mm| 20| 30
Minimum fluid level (manual
mode)| mm| 60| 50
Residual fluid height| mm| 25| 35
Weight (without accessories)| kg| 4,9| 6,5

Subject to technical modifications.

Optimising the flow rate

The flow rate is further increased:

• The lifting height is reduced.
• The diameter of the hose used is increased.
• The length of the hose used is decreased.
• The smaller the pressure loss caused by the connected up accessories.

Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us.
This declaration is invalidated by any changes made to the machine that are not approved by us.
Product: Pump
Type: 1.645-xxx

Currently applicable EU Directives
2014/35/EU
2014/30/EU
2011/65/EU
2009/125/EC
Commission Regulation(s)
(EU) 2019/1781
Harmonised standards used
EN 60335-1
EN 60335-2-41
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN IEC 63000: 2018
The signatories act on behalf of and with the authority of the company management.

Documentation supervisor: S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2021/06/01

Declaration of Conformity (UK)
We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.
Product: Pump
Type: 1.645-xxx

Currently applicable UK Regulations
S.I. 2016/1101 (as amended)
S.I. 2016/1091 (as amended)
S.I. 2012/3032 (as amended)
S.I. 2010/2617 (as amended)
Commission Regulation(s)
(EU) 2019/1781
Designated standards used
EN 60335-1
EN 60335-2-41
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN IEC 63000: 2018
The signatories act on behalf of and with the authority of the company management.

Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2021/06/01

THANK YOU!
MERCI! DANKE! GRACIAS!

Register your product and benefit from many advantages.
www.kaercher.com/welcome
Rate your product and tell us your opinion.
www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212

http://kaer.ch/er/?l=TwSoJtl9IUOwZyAe1rHDyw

4-2-SC-A5-GS-12579

References

• Cher - Official Site
• Cleaning equipment and pressure washers | Kärcher International
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>