XRocker 2113501 eSports Gaming Bed with TV Mount Instruction Manual

Table of Contents

XRocker-2113501-eSports-Gaming-Bed-with-TV-Mount-fig-1

The Orion Gaming Bed with TV Mount is a bed designed specifically for gamers. It comes in two sizes: Twin Size and Full Size. The Twin Size bed measures 82.3 x 41.3 x 42.5 inches, while the Full Size bed measures 82.3 x 56.3 x 52.5 inches. The bed is equipped with a TV mount, allowing users to easily attach their TV screens for an immersive gaming experience.
The bed is made up of various parts, including a headboard, footboard, side panels, support legs, center rails, TV rails, TV brackets, wooden slats, slat caps, drawer panels, brackets, and legs. The bed also comes with a set of fittings, including bolts, nuts, washers, an Allen key, and a wrench.
Assembly of the bed requires two people and takes approximately 1.5 hours.

Carefully open the pack and check the contents against the parts and fittings check list.
Make sure you have all the necessary parts before proceeding with the assembly.
Keep small components away from young children to avoid the danger of choking.
Gather the required tools: 2113501 (for Twin Size) or 2113601 (for Full Size), an Allen key, and a wrench.
Start assembly by following the various stages of construction outlined in the user manual.
Begin by attaching the headboard and footboard to the side panels using the provided bolts and washers.
Attach the support legs and center rails to ensure stability.
Install the TV mount by attaching the TV rails and brackets to the designated areas on the bed frame.
Attach the wooden slats to provide support for the mattress.
If using an M4 screw for the TV screen, use the provided washer (Part G) to ensure compatibility.
Ensure that the TV pole can rotate freely by loosening Screw B slightly in Step 10.
Once assembly is complete, double-check all connections and make sure everything is securely tightened.
Swap the left and right TV box if necessary.
Following these instructions will result in a fully assembled Orion Gaming Bed with TV Mount, ready for use.

PLEASE READ this sheet prior to assembly to familiarize yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit.
These items should be kept away from young children whilst assembling your unit to avoid danger of choking.

Important – Please read these instructions fully before starting assembly

Check you have all the components and tools listed on the following pages. Remove all fittings from the plastic bags and separate them into their groups.
Keep children and animals away from the work area. Small parts may cause a choking hazard.
Dispose of all packaging carefully and responsibly.
Place the product on flat and steady surface during use.
Assemble on a soft level surface to avoid damaging the unit or your floor.
Keep these instructions for further use.
Never allow anyone to sit on the foot end of the bed. Keep children well away from moving parts. If you have young children in the home, always disconnect the power at the wall socket for extra safety.
Never touch moving parts or any part of the equipment whilst in use – if something needs to be checked, disconnect the power first. The socket providing the power must be accessible at all times in case you need to switch off the power quickly.
All approved mains powered extension leads, used to power the equipment, must not be placed where they can be walked on – this is dangerous and could lead to accidents.
Do not expose the bed to an undue level of heat – keep away from radiators.
Do not place any vessel containing liquids on the TV footboard or TV itself which may accidentally spill and cause damage to your bed, the TV, the TV mount or your console.

Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
Regularly check and ensure that all bolts and fittings are tightened properly.

To ensure an easier assembly we strongly advise that all fittings are only finger tightened during initial assembly. Only upon completion of the assembly should all fixing points be fully tightened.
Make sure you have enough space to layout the parts before starting.
Check you have all the components and tools listed on the following pages. Remove all fittings from the plastic bags and separate them into their groups.
Keep children and animals away from the work area. Small parts may cause a choking hazard.
Dispose of all packaging carefully and responsibly.
Place the product on flat and steady surface during use.
Assemble the item as close to its final position (in the same room) as possible.
Parts of the assembly will be easier with 2 people.