SVEN E-727BT Wireless Stereo Headphone with Microphone User Manual

June 12, 2024
SVEN

SVEN E-727BT Wireless Stereo Headphone with Microphone

Product Information

The SVEN E-727BT is a Bluetooth wireless earphone model that provides high- quality audio and convenient hands-free calling. It is designed for users who want to enjoy music and make calls on the go without the hassle of tangled wires.

Key Features:

  • Bluetooth connectivity for wireless audio streaming
  • Built-in microphone for hands-free calling
  • Long battery life for extended use
  • Comfortable and lightweight design
  • Easy-to-use controls for music playback and call management
  • Compatible with most Bluetooth-enabled devices

Product Usage Instructions

To use the SVEN E-727BT earphones, please follow these steps:

Step 1: Charging

Before using the earphones for the first time, ensure they are fully charged. Connect the provided USB cable to the charging port on the earphones and the other end to a power source. The LED indicator will turn red during charging and will turn off once fully charged.

Step 2: Pairing

Make sure the earphones are turned off. Press and hold the power button until the LED indicator starts flashing blue and red alternately. This indicates that the earphones are in pairing mode. Enable Bluetooth on your device and search for available devices. Select “SVEN E-727BT” from the list of available devices to establish a connection.

Step 3: Music Playback

Once the earphones are paired with your device, you can start playing music. Use the volume buttons on the earphones to adjust the volume. Press the play/pause button to play or pause the music. Double press the play/pause button to skip to the next track.

Step 4: Hands-Free Calling

When receiving a call, press the power button once to answer the call. Press it again to end the call. To reject an incoming call, press and hold the power button for a few seconds. During a call, use the volume buttons to adjust the call volume.

Step 5: Power Off

To turn off the earphones, press and hold the power button until the LED indicator turns red and flashes several times. The earphones will then power off. Note: For detailed information on advanced features and troubleshooting, please refer to the complete user manual provided in the link below:

SVEN
E-727BT User Manual

SAFETY PRECAUTIONS

  •  Don’t use the stereo headphones while driving.
  •  Don’t use the stereo headphones at high volume for a long time (more than 15 minutes), as this may cause hearing impairment.

SPECIAL FEATURES

  •  Bluetooth wireless signal transmission
  •  Touch control of incoming calls and track switching
  •  Two additional sets of interchangeable ear pads
  •  Battery operation time up to 6 hours

DESCRIPTION

  1. Headphones LED indicator
  2. Multifunction sensor button
  3. Microphone
  4. Charging case LED indicator
  5. TYPE-C jack for battery charging

CONNECTION

First connection

  • Remove both headphones from the charging case, then put them back to the case to activate the headphones.
  • If there is a protective film on the contacts, you must remove it before using the headphones.
  • The battery in the headphones and case is used as an integral part of the device. Before using for the first time, make sure that the headphones are fully charged. If the headphones are discharged, they need to be fully charged (see headphone charging section).
  • Operating time using a charging case up to 24 hours

Headset to a device interfacing

  • It is necessary first to interconnect the device with a signal source (see the connection

Note: if you cannot connect the headset, try the following steps manually:

  • Remove one of the headphones from the charging case;
  • The white LED flashes quickly, touch and hold the multifunction sensor area for 6 seconds. The LED will go out. Put the headset back in the charging case;
  • Take out the other earphone and do the same.

Charging the case

  • Charge the headphone case using the USB-A to USB-C cable (included). White LEDs © flash while charging. When the case is fully charged, all 4 LEDs glow white. The left LED on the case will flash when the battery is low.

Case Headset Charging

  • Put the headphones to the charging case. During battery charging indicator ® lights red.
    When device is charged fu ll, indicator ® go out.

  • The battery in the headphones and case is used as an integral part of the device, therefore do not try to extract or replace it, because this can result in the warranty cancellation or the device damage.

Device switching on

  • Remove the headphones from the charging case and they will automatically turn on.
    Make sure the headphones are charged.

Device switching off

  • Put the headphones to the charging case. They will automatically turn off.

Headphone control
When connected to a telephone:

  • In order to receive an incoming call press twice multifunction button ©. Press button © twice again to fin ish the call.
  • Siri or Google Assistant: tap 3 times on any of the headphones*.
  • Play/pause: tap any of the headphones 2 times.
  • Next track: touch and hold the right earpiece for 2 seconds.
  • Previous track: touch and hold the left earpiece for 2 seconds

TECHNICAL SPECIFICATIONS

SVEN E-727BT-Wireless-Stereo-Headphone-with-
Microphone-02

Notes

  • Technical specifications given in this table are supplemental information and cannot give occasion to claims.
  • Technical specifications and package contents are subject to change without notice due to the improvement of SVEN production.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals