Rebel KOM1031 Wi-Fi Repeater Owner’s Manual
- June 12, 2024
- Rebel
Table of Contents
WI-FI REPEATER
model: KOM1031
OWNER’S MANUAL
KOM1031 Wi-Fi Repeater
- RJ45 scoket
- Reset/WPS button
- Status LEDs
SAFETY INSTRUCTIONS
Read this instruction manual and keep it for future reference.
- Protect this device from water, humidity and other liquids. Avoid using/storing it in extreme temperatures. Do not expose it to direct sunlight and other sources of heat.
- Keep the device out of the reach of children.
- Device for indoor use only.
- Disconnect from power outlet if the device is not going to be used for a long time.
- Do not attempt to repair this device yourself. In case of damage, contact authorized service point for check-up or repair.
- Always disconnect the product from the power source before cleaning.
- Clean this device with a soft, slightly damp cloth. Do not use any chemical agents to clean this device.
LEDs
| Diode | Status |
|---|---|
| LAN4/LAN3 | Wireless activity |
| 5,8G / 2,4 G | Wi-Fi network (in 2,4 GHz or 5 GHz band) |
| SYS/POWER | Glows green: configured correctly and working |
Flashing red: no connection
CONFIGURATION
Access Point mode configuration
- Connect the device to power outlet.
- Connect your router with the repeater by using an Ethernet cable.
- If the router is configured properly, after a few seconds the repeater will establish the connection.
- Now you can use the repeater by connecting to it wirelessly or by using the second Ethernet port.
Repeater mode configuration
-
Connect the device to power outlet.
-
Connect to the repeater:
• Wirelessly: use an external device (PC or smartphone) to connect to the repeaters network: KOM1031.
• Wired: connect the Ethernet cable to
the repeater and to an external device (PC). -
Open the browser and input following address: 192.168.19.1.
-
Open configuration wizard (Repeater menu on the PC or Repeater Settings on the smartphone).
-
Select your network (if the network works only on 2,4 GHz band, the 5 GHz band can be disabled). Press the Next button.
-
Input network password.
• By default the new network will have following name: “network_name_Ext”. Select the option to name the network manually (available on PC only).
-
Press the Finish button to save the configuration. After few seconds the network will be established. You can use the repeater by connecting to it wirelessly or by using the Ethernet port.
To reset the configuration settings, press and hold the reset button for 8 seconds.
SPECIFICATION
- Supports multiple user access: up to 10 users
- Chipset: MTK7612
- Standards: IEEE 802.11 a/b/g/n/ac
- Frequency: 2,4 GHz / 5 GHz
- Security: WEP, WPA/WPA2, WPS (64/128 bit)
- Antenna: 4x external (2 dBi)
- Transmission rate: up to 300 MB/s (2,4 Ghz) / up to 867 MB/s (5 Ghz)
- Port: 2x RJ45 (10/100 Mbps)
- Wireless range: up to 100 m (depending on environmental conditions)
- Power supply: 110-240 V; 50/60 Hz; 2 A
- Dimensions: 87 x 63 x 55 mm
- Weight: 76 g
Lechpol Electronics Leszek Sp.k. hereby declares that repeater KOM1031 is
consistent with directive 2014/53/UE.
Full text of the EU Declaration of Conformity is available at following
Internet address: www.lechpol.pl.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400
Miętne.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>