Olympia BS-812-P Programmable Thermostat User Manual

: June 12, 2024
: OLYMPIA

Table of Contents

THERMOSTAT MENU
MENU INFORMATIONS
INSTALLATION INSTRUCTIONS
INFORMATIONS
KEYPAD DESCRIPTION
DISPLAY INDICATORS DESCRIPTION
TECHNICAL CHARACTERISTICS
WARRANTY
Documents / Resources

BS-812-P Programmable Thermostat
**User Manual

**

To enter the menu, press and hold the key for 1 sec.
Navigation/setting of the menu is done with the keys
Entering the individual menus and saving the settings is done by pressing the key
To exit the menu press the key

Set time and date.

In mode (factory setting) you manually set the temperature by pressing the keys
In mode you set the weekly schedules. To set the programs, follow the steps below:

In screen Add (P1), press the key to add the program.
Set the temperature by pressing the keys and press
Set the days according to figure 1.
Set the starting hour by press the keys and press
Set the stoping hour by press the keys and press

Next, you can add more programs or you can finish the setting by navigating to screen.
Up to 20 programs can be set.
To delete the saved weekly schedules. Select the weekly schedule you want to delete, set the temperature to zero until the is displayed and press the key

Enabling this mode, the backlight of the screen remains off to save battery power.

Enabling the PIN, the temperature usage limits and the entry to the menu are locked.
Enabling PIN does not restrict the use of the functions of the home screen. If the weekly schedule and PIN number are activated , it is not possible to set the usage limits, enable the night mode and enable the absent mode. In this case the PIN number only locks the menu entry. To disable the PIN, go to the menu PIN and select . To change the PIN number you should disable the PIN number and set the PIN number from the start. In case you have forgotten the PIN number, a manual reset is possible.

Advanced menu configuration

Boiler operating time setting*.
Set the boiler operating time from 1-240 minutes. If the boiler time is 00, disable the boiler by pressing the key . Factory settting is
, Night mode temperature setting.
Factory setting is 18.0 °C.
, Absent mode temperature setting.
Factory setting is 14.0 °C.
, Calibration of the temperature sensor Factory setting is 0.0 C and can be configured from -3.0 to +3.0 °C.
, Differential setting.
This setting defines the “temperature window” between enabling/disabling of the burner output. Factory setting is 0.2 °C and can be configured from 0.2 to 1.5 °C.
, Operation mode of the thermostat (heating/cooling) For the heating mode: (factory default) and cooling: .
, Temperature display/measuring unit (Celsius degrees C or Fahrenheit degrees F)
, Factory defaults settings.
To reset the device press the key twice.

In this menu, the statistics recorded by the thermostat is displayed.

Burner operating hours.
Boiler operating hours.*
Maximum room temperature value
Minimum room temperature value
To reset the statistics, go to the screen and press the key

INSTALLATION INSTRUCTIONS

|
---|---
|
|

Wall mounting with recommended height: 1.5m from the floor on an internal wall.
Do not mount the devices in recesses, shelves, behind curtains or doors, or above or near heat sources.
Avoid direct exposure to sunlight

WARNING HEALTH AND SAFETY INFORMATION
National safety regulations
Failure to comply with national safety regulations may result in personal injury, discomfort,property damage and other potential hazards.

Comply with any national regulations and comply with appropriate safety regulations
You shall comply with any additional national regulatory informations.

Risk of electric shock
Disconnect the power supply before any interference with the system
WARNING! installation, configuration, start-up and maintenance must be done by qualified personnel only.

INFORMATIONS

GENERAL

Removing the plastic separator film between the two batteries, the thermostat is activated. The current room temperature is shown in the centre of the display. Switch-on the thermostat pressing the key
Firstly, set the current time and day, by navigating to the menu Hour. Then, set the temperature pressing the keys .
To enable the night mode press the key for 1 sec. The factory temperature setting is 18.0 °C and can be changed navigating to the menu . This mode is disabled after 8 hours.
To enable the absent mode press the key for 1 sec. The factory temperature setting is 14.0 °C and can be changed navigating to the menu .
To enable the boiler (BS-813/P & BS-813/P/C) press the key and the correspoding relay will command the boiler. The boiler will remain active as long as, it has been defined from the boti menu. In case, that the value is the factory default, then the boiler can be disabled only pressing the key
In case, the weekly schedule is enabled and change the temperature manually. The temperature remains the manual selection for 5 hours and after that the weekly schedule is been enabled again.

BATTERY REPLACEMENT
If the symbol appeared on the display, then the batteries must be replaced.
Remove the front cover and replace the batteries with new one, same type and characteristics (2 alkaline batteries ΑΑ, 1.5V). Replace the front cover. Dispose the old batteries for recycling, in compliance with current enviromental protection regulations.
ANTI-FREEZE PROTECTION
If the room temperature value is 4.5 °C, then the thermostat will enable the burner, regardless the thermostat status. This mode remains active, as long as the temperature is below 4.5 °C.

THERMOSTAT KEYPAD LOCK
To lock the thermostat press simultaneously the keys for 2 sec.
To unlock press the same keys again.

KEYPAD DESCRIPTION

DISPLAY INDICATORS DESCRIPTION

The selection temperature is smaller than the current temperature
The selection temperature and the differential is greater than the current temperature
The selection temperature is between the selection temperature and the selection + the defferential

The device is considered an electronic device for disposal in accordance with the European Guidelines and may not be disposed of as domestic garbage.

Dispose of the device through channels provided for this purpose.
Comply with all local and currently applicable laws and regulations.
Dispose of empty batteries in designated collection points.

*BS-813/P & BS-813/P/C model with boiler output

PROGRAMMABLE CHRONO – THERMOSTAT WITH COOLING AND HEATING FUNCTION

Backlight screen
2 Alkaline batteries AA (LR06)
Temperature setting 5.0 – 45.0°C with accuracy 0.1
Temperature measurement 0.0 – 99.9°C with accuracy 0.1
Anti-freeze protection to 4.5°C
Keypad lock.
Lock temperature usage limits with PIN number
Boiler output*
Temperature sensor calibration ±3.0°C
Adjustable differential 0.2 – 1.5°C
Heating/Cooling function.
Temperature Unit (°C, °F)
Up to 20 weekly schedules
ECO mode

TECHNICAL CHARACTERISTICS

WARRANTY

Thank you for your trust in our products Olympia Electronics – European manufacturer
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which accompanies each product. This warranty ceases to exist if the buyer does not follow the technical instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully agreed to them in writing. Products that have been damaged can be returned to the premises of our company for repair or replacement, as long as the warranty period is valid. Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the buyer the transportation cost.

72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.com
info@olympia-electronics.gr
940813002_09_002