SCREWFIX 146PP Reeve 5ft Outdoor Batten Instruction Manual
- June 12, 2024
- SCREWFIX
Table of Contents
SCREWFIX 146PP Reeve 5ft Outdoor Batten
Product Information
- Product Name: Reeve 5ft, Outdoor Batten
- Model Number: 146PP
- Manufacturer (UK): Kingfisher International Products Limited
- Manufacturer (EU): Kingfisher International Products B.V.
- Date of Manual: 03/11/2021
- Energy Efficiency Class: F
- Voltage: 240V 50Hz a.c.
- Lamp: 45W LED Module – 4050lm
- IP Rating: 65
- Supplied Cable: H05RN-F
Product Usage Instructions
- Commissioning:
- No specific instructions were provided.
- Fitting/Replacing Bulbs:
- Use a soft dry cloth for cleaning. Do not use solvents or abrasive cleaners.
- No instructions were provided for fitting/replacing bulbs.
- Safety Information:
- Always switch off the mains supply before adjusting or cleaning.
- If the shade protecting the LED module becomes cracked or damaged, the light fitting must be discarded.
- This light fitting is double insulated and does not require connection to an Earth circuit.
- This light fitting should be connected to a circuit with a 30mA RCD (Residual Current Device) fitted.
- Install in accordance with IEE Wiring regulations and current Building Regulations.
- To prevent electrocution, switch off the mains supply before installing or maintaining this fitting. Ensure others cannot restore the electrical supply without your knowledge.
- If in doubt, consult a qualified electrician.
- Recycling Advice:
- Waste electrical products should not be disposed of with household waste.
- Recycle where facilities exist. Check with your Local Authorityor retailer for recycling advice.
Please refer to the user manual for more detailed instructions and safety information.
Reeve 5ft, Outdoor Batten
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning : This light fitting is Double Insulated and does not require connection to an Earth circuit.
- Please read these instructions carefully before commencing any work.
- This unit must be fitted by a competent and qualified electrician.
- Install in accordance with IEE Wiring regulations and current Building Regulations.
- To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
- This light fitting should be connected to a circuit with a 30mA RCD fitted.
- If replacing an existing fitting, make a careful note of the connections.
- Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
- This product is rated at IP65.
- The entire unit gets hot whilst on for a period of time.
Specification
- Voltage : 240V 50Hz a.c
- Lamp: 45W LED Module – 4050lm
- IP rating: 65
- Supplied cable: H05RN-F
Layout
- Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting.
- Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes (not supplied) away from areas where they may be at risk of being cut, trapped or damaged.
- This product is fitted with 1.5m of H05RN-F specification cable which is an outdoor-grade, rubber-sheathed cable. The mains supply cable must have a minimum cross-sectional area of 1.0mm²
- Cables must be protected using suitable conduit or plastic trunking.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
- Refer to the diagram below. Decide on the location of the product. Measure the distance between the mounting bracket location slots & mark the location of the fixing holes on the mounting surface.
- Drill holes and fit-supplied wall plugs (suitable for masonry only – for other surfaces use appropriate fixings). Fix the mounting brackets to the ceiling using the supplied fixings.
- Wire as detailed below.
Wiring
Having correctly identified the wiring from your existing light fitting,
connect to the approved outdoor rated or approved double insulated terminal
block in the following way:
Check that…
- You have correctly identified the wires.
- The connections are tight.
- No loose strands have been left out of the connection block.
Commissioning
- Attach the product to mounting brackets by pushing until securely held.
- Replace the fuse or circuit breaker and switch on. Your light is now ready for use.
Fitting/replacing bulbs
- The LED module in this product is non-replaceable.
Fitting/replacing bulbs
We recommend cleaning with a soft dry cloth.
- Do not use solvents or abrasive cleaners as these could damage the finish.
Recycling advice
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
Safety information
For your safety, always switch off the mains supply before adjusting or cleaning. The LED module is protected by a shade. The shade provides IP65 protection and cannot be replaced, if the shade becomes cracked or damaged, this light fitting must be discarded.
- Non-replaceable control gear
- Non-replaceable light source
The light source and control gear cannot be replaced due to the IP protection becoming compromised. This product contains a light source of energy efficiency class F.
UK Manufacturer:
Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX,
United Kingdom.
EU Manufacturer:
Kingfisher International Products B.V. Rapenburgerstraat 175E, 1011 VM
Amsterdam, The Netherlands.
03/11/2021
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>