Leviton SGI65-W Two-Way In-Wall Loudspeaker Owners Manual

Leviton SGI65-W Two-Way In-Wall Loudspeaker

• WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
• WARNING: IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICIAN.
• CAUTION: NOTE THAT THIS MANUAL IS WRITTEN WITH THE ASSUMPTION THAT THE INSTALLER POSSESSES SKILL IN THE PROPER USE OF HAND AND POWER TOOLS, AND IS FAMILIAR WITH THE ENVIRONMENT BEHIND THE SURFACE OF THE WALL OR CEILING WHERE THE SPEAKERS WILL BE INSTALLED.

TOOLS AND SUPPLIES NEEDED

1. Pencil
2. Utility knife or keyhole saw
3. Stud locator
4. Drill with a 1″ (2.5 cm) flat bit
5. Phillips & flat blade screwdrivers
6. Measuring tape
7. Wire cutter/stripper
8. Fire resistant UL rated speaker wire

To determine the length and gauge of speaker wire, you will need to measure the distance between your receiver and each speaker. Remember you will need to run the wire through the walls, over the attic or under the crawl space of your home.

• Always buy more speaker wire than you think you will need.
• Equal speaker wire length for each channel should always be used to maintain an equal balance in sound volume.
• Sound quality is lost when too thin a wire gauge is used over a long distance. A speaker wire of 18-gauge or thicker is recommended.

Fire resistance UL rated speaker wire gauge chart

Length: Minimum Gauge

• Up to 50 feet (15 m) 18-gauge
• 50-150 feet (15-45 m) 16-gauge (thicker)
• Over 150 feet (45 m) 14-gauge (thickest)

NOTE: The smaller the number of wire gauge means it is a thicker wire.

PAINTING

To match the décor of your home you may wish to paint the visible portion of your speaker. First use Latex wall paint or Aerosol spray paint for the paint job, then cover the speaker grille with a coat of anti-rust paint.

NOTE: Prior to painting, remove cloth inside grille.

Directions:

1. Remove the speaker grille carefully. Loosen the grille using a small screwdriver.
2. To paint the housing, mask the inner area using the painting template provided.
3. Start to paint.
4. After the paint has thoroughly DRIED, carefully remove the template.

NOTE: There is no need to replace the grille at this time because you will need access to the inner speaker surface during the installation.

SPEAKER PLACEMENT & POWER HANDLING

Speaker Placement:

• The installation of these speakers is permanent. For the best results, the speakers should be mounted on a clean, flat surface indoors.
• It is a good idea to temporarily hook up your speakers, or use the existing speakers to determine the best locations for your new speakers prior to the installation. For the ultimate stereo effect, we recommend that your speakers should be separated 4 to 6 feet (1.2-1.8 m) apart from each other. In-wall speakers should be placed at the “ear level”, approximately 3 to 5 feet (0.9-1.5 m) above the floor.
• To avoid distortion, mount the speakers at least 6 feet (1.8 m) away from any television or monitor.

Power Handling (10 Watts minimum):

• Not all receivers/amplifiers can safely operate 2 pairs of speakers at the same time. Please refer to the owner’s manual provided by the manufacturer of your receiver/amplifier.
• The speakers which you are about to install are rated at 8-ohm impedance (6-ohm minimum). If you intend to operate your main speakers with your newly installed speakers, it is important to check if they are compatible. Locate the connection terminal on your main speakers where the impedance level is often printed, or refer to the owner’s manual. If they are rated at 8-ohms, they are compatible and can be operated simultaneously.

INSTALLATION

Procedure (refer to Installation Diagram):

1. Locate the studs in the area you want to mount your speakers.

2. Use a level to ensure straightness.

3. Trace the inside of your mounting template with a pencil.

4. Carefully drill a 1″ (2.5 cm) hole in the center of your traced cutout. CAUTION: ENSURE THAT EXISTING HOUSEHOLD CABLES, PIPES AND DUCTS ARE NOT PRESENT IN THE WORKING AREA.

5. With a utility knife or keyhole saw, cutout the center area.

6. Remove the center area using the 1″ (2.5 cm) hole.

7. Remove the speaker grille using a small flat-headed screwdriver to pry it off.

8. To ensure proper fit, temporarily place the speaker in the open area.

9. Repeat steps 1-8 for any additional speakers.

10. Decide where your receiver will be placed.
    NOTE: Each individual speaker wire will need to be routed to this area.

11. Drill a 1″ (2.5 cm) hole in the wall where your receiver will be located.

Wiring Your New Speakers (refer to Installation Diagram):

1. Measure the distance from the nearest corner of the room to the center of the cutout.
2. Measure the distance from the nearest corner of the room to the 1″ (2.5 cm) hole where your receiver is located.
3. With these measurements and UL rated speaker wire go to the attic.
4. Locate the corner of the room where your measurement for Step 1 was taken from. Measure the exact distance in the correct direction of your cutout and mark it with a pencil.
5. Drill a 1″ (2.5 cm) hole.
6. Insert the wire through the hole and feed until the wire is visible through the cutout.
7. Leave about 2 feet (0.5 m) extending through the cutout.
8. Locate the corner of the room where your measurement for Step 2 was taken from. Measure the exact distance in the correct direction of the 1″ (2.5 cm) hole and mark it with a pencil.
9. Drill another 1″ (2.5 cm) hole.
10. Insert other end of wire used in Step 6 through this hole and feed until its visible through the 1″ (2.5 cm) hole at your receiver.
11. Leave about 2 (0.5 m) feet of wire extending through the hole.
12. Repeat steps 1 to 11 for each speaker.

Speakers:

1. Strip 1/2″ (1.2 cm) of insulation off the wire and tightly twist the wire strands.
2. Attach the speaker wire to the Red/Black speaker terminals. Red = Positive, Black = Negative.
3. Loosely attach the mounting bracket to the speaker with the screws provided.
4. Insert the bottom portion of your speaker bracket behind the wall/ceiling, then insert the top.
5. Tighten all screws evenly and firmly.
6. Place the rubber adhesive strips on the inner portion of the speaker frame. Insert the speaker grille. The rubber strips will ensure a secure fit.
7. Repeat Steps 1 to 6 for each speaker.

Receiver:

1. Strip 1/2″ (1.2 cm) of insulation off each wire and tightly twist the wire strands.
2. Connect the wires to the Red/Black speaker terminals on your receiver. Red = Positive, Black = Negative.
3. Repeat Steps 1 to 2 for each speaker wire.
4. Your installation is now complete.
   Note: For a professional installation, use Leviton’s optional Dual Spring Clip Wallplate, Cat No. 40952.

WALL AND CEILING MOUNT INSTALLATION DIAGRAM

(Use this diagram as a reference only, wiring schemes may differ)

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such two year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com

FREQUENTLY ASKED QUESTIONS

What is the Leviton SGI65-W Two-Way In-Wall Loudspeaker?

The Leviton SGI65-W is a two-way in-wall loudspeaker designed to be installed directly into walls, providing a discreet audio solution.

What is the speaker's design and purpose?

The speaker is designed to be mounted within walls, offering a space-saving and visually unobtrusive way to deliver audio in a room.

What is the speaker's driver configuration?

The SGI65-W typically features a two-way driver configuration, which includes a tweeter for high frequencies and a woofer for mid-range and low frequencies.

What is the speaker's power handling capability?

The power handling capability of the speaker, which indicates the amount of power it can handle without distortion, should be specified in its documentation.

Is the SGI65-W suitable for both residential and commercial applications?

Yes, this speaker can be used in both residential and commercial settings to provide background or primary audio.

Is the speaker easy to install?

The SGI65-W is designed for in-wall installation and may require some level of expertise in installation.

What is the frequency response range of the speaker?

The frequency response range typically spans from low to high frequencies, such as 60Hz to 20kHz.

Does the speaker require an external amplifier?

Yes, like most passive speakers, the Leviton SGI65-W requires an external amplifier to deliver audio signals.

Is the speaker magnetically shielded?

Magnetic shielding prevents interference with nearby electronic devices. The product documentation will specify whether the speaker is magnetically shielded.

Can the SGI65-W be painted to match room decor?

Yes, many in-wall speakers can be painted to blend seamlessly with the room's aesthetics.

What type of grille does the speaker have?

The speaker may feature a paintable grille that can be customized to match the surrounding environment.

What are the recommended applications for this speaker?

The speaker is often used for distributed audio, background music, or home theater setups.

Does the SGI65-W speaker provide stereo sound or is it mono?

The speaker can be used in stereo setups if paired with another speaker, or it can be used in mono configurations depending on your audio setup.

Is there a cutout template provided for installation?

Yes, many in-wall speakers come with cutout templates to guide proper installation.

Can the speaker be used in damp or humid environments like bathrooms?

The suitability of the speaker for damp environments should be checked in the product specifications. Some models are designed for such environments.

VIDEO – PRODUCT OVERVIEW

DOWNLOAD THE PDF LINK:Leviton SGI65-W Two-Way In-Wall Loudspeaker Owners Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>