FULGOR MILANO FPRHD 362 TC X Wall-Mounted Cooker Hood Instruction Manual

FULGOR MILANO FPRHD 362 TC X Wall-Mounted Cooker Hood

Product Information:
Product Name: FPRHD 362 TC X, FPRHD 482 TC X, FPRHD 362 TC MBK,FPRHD 482 TC MBK
Product Type: Cooker Hood Hotte
Language: Italian (IT), English (EN), French (FR), Spanish (ES), German (DE)
Manual Sections: Installation, Use and Maintenance Instructions
Product Usage Instructions

1. Using the provided drilling template, create holes  for wall bracket installation. The products must be positioned at adistance of 650mm from the cooking surface.
2. Attach the wall brackets to the wall using the provided plugs and screws.
3. In the filtering version , the air and vapors conveyed by the appliance are purified by a grease filter and an active carbon filter, and then recirculated into the environment through the side grilles of the chimney. In the filtering version, it is recommendedto use an air deflector (dis.1A) placed at the top of the pipe to allow air recycling in the environment.
4. Attach the suction unit to the previously fixed wall brackets.
5. Install the four fixing screws in the holes located at the top of the product. Screw the front screw to secure the product to the wall, then check that the hood is perfectly level. If not, adjust the rearscrews by screwing the right one to raise the right side of the hood or screwing the left one to raise the left side of the hood.
6. Lock the hood by inserting the two screws into the back of the hood .
7. After determining the height of the decorative pipes, attach the tube support brackets to the ceiling or wall at a distance of 813.5mm (for model FPRHD 362) and 1118mm (for model FPRHD 482) . Then, place the two decorative chimneys above the hood, lift the upper chimney, and fix it to the previously positioned brackets with the two provided screws .

   ---

Maintenance

• An accurate maintenance guarantees good fun-ctioning and long-lasting performance.
• Particular care is due to the grease filter.
• The metal grease filter is removed by pushing the specific filter handle towards the hood rear side, rotating the filter downwards
• After 30 hour working, the grease filter saturation will be signaled by the simultaneous lighting of speed indicators; select the timer function with the hood off to reset it.
• The grease filter needs cleaning by regular hand-washing or in dishwashers, every two months at least, or depending on its use.
• If the appliance is used in the filtering version, the activated charcoal filter needs to be replaced periodically.
  • The charcoal filter is removed by removing the grease filter first, following the instructions above, then by pulling its special plastic tongue until it is released from its seat.
  • The charcoal filter is inserted by following the re-verse procedure.
  • Tepid water and neutral detergents are recom-mended to clean the appliance, while abrasive products should be avoided.
  • The power cord shall be replaced by authori-zed personnel only.

Substitution of the LED bar :

• Using an appropriate tool, remove the LED bar from its seat  disconnect it elec-tronically using the appropriate connector then substitute it with a LED bar with same charac-teristics.

Note: Please refer to the complete user manual for detailed instructions and safety precautions.

WARNINGS

• this appliance can be used by children aged from 8 years and above and persons with redu-ced physical, sensory or men-tal capabilities or lack of expe-rience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards in-volved.
• Children shall not play with the appliance.
• Cleaning and user maintenan-ce shall not be made by chil-dren without supervision.
• If the supply cord is damaged, it must be replaced by the ma-nufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• There is a fire risk if cleaning is not carried out in accordance with the instructions;
• Do not flambé under the range hood.
• The air must not be dischar-ged into a flue that is used for exhausting fumes from ap-pliances burning gas or other fuels (not applicable to applian-ces that only discharge the air back into the room);
• This appliance and its accessi-ble parts are likely to become very hot if used in combina-tion with cooking devices.
• In case of installation with gas hobs the cooker surface and the inferior part of the cooker hood must be at a minimun distance of 65 cm.
• To evacuate the air outlet, ple-ase comply with the pertaining rules given by competent au-thorities.
• When performing the electrical connections on the appliance, please make sure that the po-wer supply is provided with earth connection and that vol-tage values correspond to tho-se indicated on the label pla-ced inside the appliance itself.
• If the supply cord is damaged, it must be replaced by the ma-nufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Before carrying out any cle-aning or maintaining opera-tions, the appliance needs to be removed from the electric grid.
• If the appliance is not provided with a non-separable flexible cable and plug, or with ano-ther device ensuring discon-nections from the grid, with an opening distance between the contacts of at least 3 mm, then such disconnecting devices must be supplied within the fi-xed installation.
• If the fixed appliance is equip-ped with power cord and plug, the appliance shall be instal-led in a place where the plug is easily reachable.
• Before carrying out the instal-lation of the appliance, please check that all components are not damaged. In such a case, make contact with your retai-ler and do not proceed with the installation.
• Should the product show any anomaly, disconnect the ap-pliance from the power supply.
• When the range hood and ap-pliances supplied with energy other than electricity are si-multaneously in operation, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).

USES

The appliance has been designed to work both in filtering and sucking mode.

• In the filtering version, the air and fu-mes conveyed by the appliance are purified by both a grease filter and an activated charcoal fil-ter, and then re-circulated into the room through the side-grids of the chimney.
  When the appliance works in this mode, we re-commend the use of an air deflector (Fig. 1A) to be placed on the upper part of the pipe, allowing the air to be re-circulated into the room.

• In the sucking version, fumes are di-rectly conveyed outside the building, through the top or rear air out-let. The use of a charcoal filter and air deflector is not necessary in this case.

INSTALLATION

*Before installing the appliance, make sure that none of the parts is damaged in any way.
In case of damaged parts, contact your retailer and do not proceed with installation.
Read all of the following instructions carefully be-fore installing the appliance:

• Use an air outlet pipe of the shortest possible length.
• Limit the number of pipe elbows.
• Use a material approved by standards and regulations.
• Avoid any sudden changes in the pipe section (recommended constant diameter: Ø 200 mm or equal surface area).
• The manufacturer shall not respond for air ca-pacity or noise problems due to non- compliance with above mentioned instructions, and no war-ranty shall be given.

The appliance air outlet is directed upwards:
if you prefer to have the air outelt directed to-wards the rear side of the appliance, you will need to replace the air outlet upper fittig with the rear one supplied with the appliance.Remove the grease filter before installation, in order to prevent the appliance from being dama- ged.
To remove the metal grease filter, push the speci-fic filter handle towards the hood rear side, rota-ting the filter downwards Drill the holels to fix the wall bracket, using the related template ; Appliances shall be installed at 650 mm from the hob surface. Fasten the brackets to the wall using the dowels and screws supplied with the appliance.

Hang the suction body to the wall bra-ckets previously fixed. Fit the four fixing screws into the holes found on the appliance top side.Tighten the front screw to secure the appliance to the wall, then check that the hood is perfectly flush; if not, act on the rear screws and tighten either the right screw to lift the appliance right side, or the left one to raise the hood left side.
Fasten the hood by inserting the two screws into the rear side of the appliance. After determining the height of decorative pipes, fix the pipe support brackets either on the ceiling or the wall at a centre distance of 813.5mm (for the FPRHD 362 model) and 1118mm (for the FPRHD 482 model) , then place the two-decorative chimneys on the hood, lift the upper chimney and fix it to the brackets previously posi-tioned with the two screws provided .

WORKING

• A: Light ON/OFF button
• B: Speed indicators
• C: Speed indicators
• D: Speed increase
• E: 10 Minute Timer

TIMING
As a result of the new EU65 “Energy label” and EU66 “ Ecodesign” regulations issued by the Eu-ropean Commission, which came into force as from January 1st, 2015 , our products have been adapted to comply with these new requirements. All of the models complying with the energy label requirements, are equipped with new electronics including a timer device for suction speeds con-trol, when the air capacity exceeds 650m³/h. Internal motor models, with maximum air capa-city higher than 650m³/h, are equipped with a timer device that automatically switches the suc-tion speed from 4th to 3rd speed, after 5 minutes operation.
Motors, whose air capacity exceeds 650m³/h at both 4th and 3rd speed , will have the following by default timer control functions: The suction speed is automatically switched from 4th to 2nd speed, after 6 minutes operation.
If the appliance is working at 3rd speed, it is auto-matically switched to 2nd speed, after 7 minutes operation. Operation speeds can also be chan-ged during operation.
The energy consumption of the appliance in stand – by mode is lower than 0.5W.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collec-tion point for the recycling of electrical and electronic equipment. By ensuring this pro-duct is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this pro-duct, please contact your local city office, your household waste disposal service or the shop where you purchased the product. This appliance is marked according to the Eu-ropean directive 2012/19/EC on waste electrical and electronic equipment (WEEE)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>