COAST TO COAST ENTERTAINMENT 804MAN001 6 Player Prize Cube Crane User Manual
- June 12, 2024
- COAST TO COAST ENTERTAINMENT
Table of Contents
- COAST TO COAST ENTERTAINMENT 804MAN001 6 Player Prize Cube Crane
- Product Information
- Product Usage Instructions
- Game Dimensions
- Setting Up Your Prize Cube
- Menu Options
- Audit Menu
- Error Codes
- Connection Overview
- Wiring Diagrams
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
COAST TO COAST ENTERTAINMENT 804MAN001 6 Player Prize Cube Crane
Product Information
The product is a Prize Cube, manufactured by Coast
Entertainment. The dimensions of the game are as follows:
- Game Dimensions: 102 in (2591mm) x 89 in (2260 mm) x 98 in (2489 mm)
- Installed Palleted: 102 in (2591 mm) x 85 in (2159 mm) x 94 in (2388 mm)
- Weight: 1645 lbs/746 kg
Product Usage Instructions
- Setting Up Your Prize Cube:
- There shall be another piece of small plate which is packed separately with the machine. Inside the machine there shall be 2 pieces of big half round plate, 2 aluminum sticks and 1 motor.
- Put 2 sides of the machine together using 12 screws to secure the bottom and 6 to secure the top. Note: The direction of the screw must be as shown.
- Put the small plate inside then mount motor as shown.
- Plug in the 2 connectors (Main Power and Motor) as depicted below.
- Pull LED light connector through the roof.
- Mount the wood boards to the top.
- Plug in the LED connector into the metal housing.
- Mount the metal housing onto the top wood.
- Install the half round art plate.
- Using the 2 metal plates to sandwich the acrylic pieces and cover the seam.
- Slide the aluminum cover into each joint.
- Install the corner caps.
- Menu Options:
- To enter the crane settings window, press and hold K2 for approximately 2 seconds. The front console display should come up with the below options.
- Navigate the options using the menu option with K1 and K2, to select a menu option use K0, and to go back or exit menus use K3.
- Target % – The payout ratio is as follows: Prize Cost x (100% + Percentage) / Game Cost = X game 1 prize Rate – 1-999% Adjust the machine’s prot rate. Default set to 10% Prize Cost – 1-999.9 Cost for the prize. Game Cost – 1-999.9 Price for each game. X game 1 prize Calculations for the above settings.
- Pay Til Win Close / 1 game 1 prize Turn on play until function and set how many games to play until win. Keep after 90s / Clear after 90s Clear the record after 90s or not Hide times / Display times Keep the record or not after restart machine restart. Reboot keep / Reboot Clear Keep the record or not after restart. Price – $0 (1-2000) Prize value to be shown on the display for players.
- Gantry Position Home – Left front/left back/left front/left right Claw home position Exit – Left front/left back/left front/left right Exit position Claw start at 1.3s Claw move to center when credit insert Exit drop at 1.0s Claw goes down to drop prize at exit String length 2.0s Floor height to avoid claw pass over
- Claw Speed Front-Back – 36 Adjustable forward/backward motor speed. Left-Right – 39 Adjustable Left/Right motor speed. Up-Down – 48 Adjustable claw dropping speed.
- Coin 1 Pulse 1 Coin = 1 Credit – 1-99 Coin mech 1 value setting
- Coin 2 Pulse 1 Coin = 1 Credit – 1-99 Coin mech 2 value setting.
- DBA Pulse 1 P = 1 Credit Dollar Bill Accepter value setting.
- Pulse per Play 1 Game = 1 Credit – 0-50 Game price, 0 = Free Play Mode
- Game time 1-99 Game time, Default set to – 20s
- Ticket 1 Coin 0 Ticket How many tickets are paid with each game play.
service@coastentertainment.com
P: 561.588.5200 | Fax: 561.493.2999
2201 4th Avenue N, Lake Worth Beach,FL 33461
Game Dimensions
Game Dimensions
Installed| 102 in (2591mm) x 89 in (2260 mm) x 98 in (2489 mm)| 1645lbs/746kg
Palleted| 85 in (2159 mm) L x 85 in (2159 mm) W x 94 in (2388 mm) H|
1,660lbs/753kg
Setting Up Your Prize Cube
- There shall be another piece of small plate which is packed separately with the machine. Inside the machine there shall be 2 pieces of big half round plate, 2 aluminum sticks and 1 motor.
- Put 2 sides of the machine together using 12 screws to secure the bottom and 6 to secure the top.
- Put the small plate inside then mount motor as shown.
- Plug in the 2 connectors (Main Power and Motor) as depicted below.
- Pull LED ligh connector through the roof
- Mount the wood boards to the top
- Plug in the LED connector into the metal housing
- Mount the metal housing onto the top wood
- Install the half round art plate
- Using the 2 metal plates to sandwich the acrylic peices and cover the seem.
- Slide the aluminum cover into each joint
- Install the corner caps.
Menu Options
To enter the crane settings window press and hold the K2 for aproximately 2
seconds. The front console display should come up with the below options.
Navigate the option using the menu option with K1 and K2, to select a menu
option use K0, and to go back or exit menus use K3.
-
Target % – The payout ratio is as followed:
- Prize Cost x (100% + Percentage) / Game Cost = X game 1 prize
- Rate -1-999%
- Adjust the machines profit rate. Default set to 10%
- Prize Cost- 1-999.9
- Cost for the prize.
- Game Cost – 1-999.9
- Price for each game.
- X game I prize
- Calculations for the above settings.
-
Pay Til Win
- Close / I game I prize
- Turn on play until fucrtion and set how many games to play until win.
- Keep after 90s / Clear after 90s
- Claer the record after 90s or not
- Hide times / Display times
- Keep the record or not after restart machine restart.
- Reboot keep / Reboot Clear
- Keep the record or not after restart.
- Price – so (1-2000)
- Prize value to be shown on the display for players.
-
Gantry Position
- Home – Left front/left back / left front / left right
- Claw home position
- Exit – Left front/left back / left front / left right
- Exit position
- Claw start at 1.3s
- Claw move to center when credit insert
- Exit drop at I.Os
- Claw goes down to drop prize at exit
- String lenth 2.0s
- Floor height to avaoid claw tips over
-
Claw Strength
- Max – 1-48V
- Grabbing power, better not lower than 30V. Default set to 35V
- Min – 1-24V
- Retaining power, can set automatically at the lasxt section. Default set to 15V
- Change time – 0.0 – 10s
- Holding time in between grabbing power and retaining power, voltage will be dropping smoothly
Auto detect – Min 6
Retaining power auto detect by following the below instructions
- Place prine in claw, press drop button to grab onto the prize
- Press drop button again, system will lower the grab power until prize drops through the sensor
- Retaining power level will be saved on the display
-
Claw Speed
-
Front-Back – 36
-
Adjustable forward/backward motor speed.
-
Left-Right – 39
Adjustable Left/Right motor speed. -
Up-Down – 48
Ajustable claw dropping speed.
-
-
Coin 1 Pulse
- 1 Coin = 1 Credit – 1-99
- Coin mech 1 value setting
-
Coin 2 Pulse
- 1 Coin = 1 Credit – 1-99
- Coin mech 2 value setting.
-
DBA Pulse
- 1 P = 1 Credit
- Dollar Bill Accepter value setting.
-
Pulse per Play
-
1 Game = 1 Credit – 0-50
-
Game price, 0 = Free Play Mode
-
Game time
- 1-99
- Game time, Deafult set to – 20s
-
Ticket
- 1 Coin 0 Ticket
- How many tickets are paid with each game play.
-
Grab in air
- Yes / No
- Player can control the closing of the claw. Default set to yes.
-
Credit History
- Keep/Clear
- Choose if the machine keeps the credit after reboot
-
Attract Music
- Music Select 1-7 / Yes
- Demo music setting, 7 sounds for option.
-
Bonus Coin
Yes / No
Bonus Credit setting -
Winner Show Off
Yes / No
Winner game not winning function On or Off
1 Chance
Winner game not winning extra free game
All Show Off / Half Show Off
Winner game effects show up randomly -
KLED Color Set
-
Green
-
Red
-
Light Green
-
Blue
-
Purple
-
Light Blue
-
White
Button and joystick light color selection.
Hold/Flash
Button and joystick light 昀椀xed or 昀氀ashing e昀昀ect.
Audit Menu
Press K0 to enter Audit menus options, once in press K3 as prompted on screen to leave.
-
Total Income
Total of credits inserted into machine -
Current Income
Total credits insterted since last cleared -
Coin 1 Income
Total income on Coin 1 since last cleared -
Coin 2 Income
Total income on Coin 2 since last cleared -
DBA Income
Total income from Dollar Bill Validator since last cleared -
Total Prize Out
Total prizes won -
Total Ticket
Total tickets paid out (optional) -
Total Play
Total games played
Pressing K1 and K2 together will clear current amount.
Pressing K0 and K2 tpgether will clear all options.
Error Codes
Error codes will show at the bottom of the display at all times.
Error Code | Fixes |
---|---|
Coin 1 Error | 1. Check the mechanism if it is broken |
2. Check the coin stuck
Coin mech set in “No” mode
Memory Error| 1. Reset machine to default setting by turning the game o昀昀 then pressing K0 + K3
and powering back on
Coin 2 Error| 1. Check the mechanism if it is broken
2. Check the coin stuck
Coin mech set in “No” mode
DBA Error| 1. Check the DBA is not broken
2. Check the entrance does not have a jam
Our Prize Red Error| 1. Check the sensor LED (Green/Red lights on is not normal)
2. Check the prize exit for any obstruction
No Ticket Error| 1. Check for ticket jams at dispenser
2. Check ticket dispenser is operational
In Count 1 Error| 1. Check for loose cable
2. Replace counter
In Count 2 Error| 1. Check for loose cable
2. Replace counter
Out Count Error| 1. Check for loose cable
2. Replace counter(s)
Le昀琀 SW Error| Gantry Le昀琀 Stop Switch Error
1. Check for loose cable at switch.
2. Make sure switch is wired properlly (Signal line to NO)
3. Replace Switch
Right SW Error| Gantry Right Stop Switch Error
1. Check for loose cable at switch.
2. Make sure switch is wired properlly (Signal line to NO)
3. Replace Switch
Front SW Error| Gantry Front Stop Switch Error
1. Check for loose cable at switch.
2. Make sure switch is wired properlly (Signal line to NO)
3. Replace Switch
Error Code | Fixes |
---|---|
Upper Sw error | Claw Up Stop Switch Error |
1. Check for loose cable at switch.
2. Make sure switch is wired properlly (Signal line to NO)
3. Replace Switch
Down Sw error| Claw Down Stop Switch Error
1. Check for loose cable at switch.
2. Make sure switch is wired properlly (Signal line to NO)
3. Replace Switch
Other Errors | Fixes |
---|
Claw remaines closed
a昀琀er power up
| 1. Replace claw coil
2. check/replace bottun and lamp on front console
Gantry not moving properly| 1. Check the fuse on power supply
2. Check the 48V
Claw doesn’t close
during game mode
| 1. Check the fuse on the PCB
2. Replace claw coil
Game is unresponsive when powered on| 1. Check fuse on power outlet
2. Game is plugged in
No credit when coin is inserted| 1. Be sure the coin mech is set properly (NO)
2. Replace coin mechanism
Replacing Claw String| 1. Be sure the string direction is correct
Connection Overview
Notes:
- Make sure the opposite wall from the sensor has the black aphotic paint sticker, or the sensor will not work properly.
If the following errors persist contact our customer service.
A. Red light always on or blinking
B. Green light always on (this means the prize is stuck or something is blocking the sensor)
Wiring Diagrams
Connector | Usage | Color | Connector | Usage | Color |
---|
Power Supply
| 12V| Yello|
LCD Display
| GND| Blue
48V| Blue| P10| Green
GND| Black| P11| Yellow
24V| Green| P12| Orange
5V| Red| P13| Red
GND| Black| P14| Brown
5V| Black
Voltage Meter| V-| Brown| Speakers| V-| White
V+| Black| V+| Gray
Connector J3 off stage one board
2201 4th Ave N. Lake Worth Beach, FL 33461
www.coasttocoastcranes.com
1-800-224-1717