Coast to Coast ENTERTAINMENT Cranes Owner’s Manual

: August 7, 2024
: COAST TO COAST ENTERTAINMENT

Table of Contents

SETTING THE CLAW STRENGTH
DIP SWITCH SETTINGS
WIRING DIAGRAM
ERROR CODES
CUSTOMER SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Coast to Coast ENTERTAINMENT Cranes

SETTING THE CLAW STRENGTH

First VR1 : When the claw first picks up the prize in the down position.

Second VR2 : When the claw reaches the up position and carries the prize to the prize drop point.

To set the claw strength do the following:

Start a game by pressing the freeplay button
During gameplay press the freeplay button to enter setup mode
01 should be flashing on the screen allowing you to adjust VR1
Press the claw drop button on the control panel to change LED to 02
Now you can adjust the VR2
Press the freeplay button again to save the settings

*VR3 Not used

DIP SWITCH SETTINGS

DIP SW 1 : Not Used
DIP SW2

1=ON 0=OFF

FUNCTIONS/ SWITCH	1	2	3
CLAW MOVES TO MIDDLE AT BEGINING OF PLAY	YES	1
NO	0
DI SPLAY	CREDIT		0
PLAY		1

DIP SW3

1=ON 0=OFF

MODE/ SWITCH POSITION	1	2	3	4	5	6	7	8
COIN MECH 1	1 COIN 1 CREDIT	0
1 COIN 2 CREDITS	1
BILL ACCEPTOR	1 PULSE 1 CREDIT		0
1 PULSE 2 CREDITS		1
4 CREDITS GET 1 PLAY	NO			0
YES			1
CREDIT TO PLAY	1 CREDIT 1 PLAY				0	0	0
2 CREDITS 1 PLAY				1	0	0
4 CREDIT S 1 PLAY				0	1	0
8 CREDITS 1 PLAY				1	1	0
20 CREDITS 1 PLAY				0	0	1
28 CREDITS 1 PLAY				1	0	1
4 CREDITS 3 PLAYS				0	1	1
20 CREDITS 15 PLAYS				1	1	1
GAME TIME	15 SEC							0
30SEC							1	0
45SEC							0	1
60SEC							1	1

DIP SW4

1=ON0=OFF

MODE/ SWITCH POSITION	1	2	6	7	8
COIN MEMORY	CLEAR	1
SAVE	0
HOM EPOSITION ISN’T THE SAME AS THE EXIT		0
HOME POSITION ISTHE SAME AS THE EXIT		1
NO T USED
NOT USED
NOT USED
ATTRACT MODE MUSIC	ON			0
OFF			1
SENSOR CHECK	ON ( TEST)				1
OFF (OPEN)				0
PLAY UNTIL YOU WIN OPTION	ON
OFF					1

PS1 ENTER SENSOR MODE : DISPLAY WILL SHOW” 11 “, PLEASE CHECK IF SENSOR CAN SENSE WITH A STUFF. TURN OFF SWITCH BACK TO OPERATE AFTER CHECK

WIRING DIAGRAM

( A ) J1 : D Type connector ( TO CRANE )
Look chart ( 3 )

( B ) J2 : Power connector

: GND BLACK
: + SV RED
: + 24V ORANGE
: – 48V YELLOW
: +48V GREEN
: + 12V BLUE

( C ) J3 : Speaker, Sensor connector

: + 12V **RED**
: GND BLACK
: Sensor out WHITE
: Sensor in BROWN
: FREE PLAY ORANGE
: Balancer BLACK
: NC
: NC
: Speaker+ GRAY
: Speaker – PURPLE

( D ) JS : Coin selector, Rotary motor control Counter connector

: GND
: GND BLACK
: GND
: Coin selector 1 signal
: Coin selector 2 signal WHITE
: Inhibit Coin Mech signal GREEN
:
: Coin selector 1 power+ 12V RED
: Counter out BLUE
: Counter in GREEN
: Counter power + 12V RED
:

( E ) JG : Direction ket

: Key (get) BLUE
: Key ( down )
: Key (left) YELLOW
: Key ( right ) ORANGE
: Key ( back ) RED
: Key ( foward ) BROWN
: GND BLACK

( F ) J7 : Display connector

( G ) J10 : Display connector

J 1. 25 PIN CONNECTOR WIRE LIST

DESCRIPTION| FORWARD MOTOR| LEFT OR RIGHT MOTOR| UPOR DOWN MOTOR| POWER SUPPLY FOR CLAM| FRONT LIM IT SWITCH| HOME LIMIT SWITCH| LEFT LIMIT SWITCH| TOP LIMIT SWITCH| BOTTOM LIMIT SWITCH
---|---|---|---|---|---|---|---|---|---
REFERENCE NUMBER| 1,14| 2,15| 3,16| 4,17| 5| 6| 8| 9| 10
QTY PER ASSEMBLY| 1| 1| 1| 1| 1| 1| 1| 1| 1

ERROR CODES

ERROR NO	CAUSING	SOLUTION
1	UP-AND-DOWN MOTOR	CHECK UP-AND DOWN MOTOR SWITCH
2	FORWARD-AND-BACK MOTOR	CHECK FORWARD-AND BACK MOTOR SW
3	LEFT-AND-RIGHT MOTOR	CHECK LEFT-AND-RIGHT MOTOR SW
4	COIN MECH 1	CHECK COIN MECH “NO” SETTING
6	FORWARD-AND-BACK MOTOR	CHECK FORWARD-AND BACK MOTOR SW
8	MAIN PCB RAM	CHANGE NEW RAM IC
11	SENSOR TEST MODE	EXIT TEST MODE DIP7ON SW4
71	DROP BUTTON STUCK	CHECK/ REPLACE BUTTON
*	CLAW NO FUNCTION	CHECK DC COIL OR FUSE

CUSTOMER SUPPORT

COMPATIBLE WITH THE FOLLOWING CRANES :
TOY TAXI/ HOT STUFF/ SWEET STUFF
DUCK/ ZOO/ DEEP SEA CATCHER
1.800.224.1717
1000 TOWBIN AVE. LAKEWOOD NJ 08701
WWW.COASTENTERTAINMENT.COM