Kaiser KCGx Grand Chef 30cm Domino Gas Hob User Manual

KG •••1 G •••
BUILT IN COOKING HO OGAS

KCGx Grand Chef 30cm Domino Gas Hob

DEAR CUSTOMERS,
thank you for purchasing this Kaiser product.
We are convinced that you have made a right choice. This product which satisfies the high quality demands and corresponds to world comprehensive standards realizes your cookeries, and his modern appearance which has been developed by the best European designers will decorate your kitchen splendidly.
We ask you to read the operating instructions before usage thoroughly. The consideration of recommendations protects you from possible inconveniences which can appear as a result of the wrong use of the cooking hobs, and allows you  to reduce the consumption of gas and electric energy. If the use corresponds to the present operating instructions, the cooking hob will bring you a lot of pleasure for a long time.
Our cooking hobs correspond to the main demands of the security, hygiene and environment protection, according to the directives of the EU which is confirmed with certificates DIN ISO 9001, ISO 1400, according to the norms counting within the frames of the EU, they also correspond to the Gosstandart of Russia, standards of the CIS, which is confirmed with the corresponding certificates.
With the thoughts of a constant improvement of the quality of our cooking hob the changes in design and equipment which lead only to positive changes of the technical qualities are reserved by the manufacturer.
We wish you an effective use of our cooking hob.
Yours faithfully

OLAN-Haushaltsgeräte
Berlin Germany
We Inform you that our devices which are the object of the present operating instructions are precurtain exclusively for the domestic use.

NSTALLATION INSTRUCTIONS

Attention! Installation and electrical connection must be made by a qualified expert only.
Attention! The manufacturer declines all responsibility for damage or injury if the above instructions and normal safety precautions are not respected.

ELECTRICAL CONNECTION
Before connecting the cooking hob to the mains power supply, make sure that:

• the plant characteristics are such as to follow what is indicated on the matrix plate placed at the bottom of the working area,
• the mains supply has an efficient ground connection complying with all applicable laws and regulations.

Correct grounding is a legal requirement. If the appliance is not pre-fitted with a power cable and/or plug, use only suitable cables and plugs capable of handling the power specified on the appliance’s data plate and capable of resisting  heat. The power cable should never reach a temperature 50°C above ambient temperature at any point along its length.
If the appliance is to be connected directly to mains terminals, fit a switch with minimum aperture of 3 mm between the contacts. Make sure that the switch is of sufficient capacity for the power specified on the appliance’s data plate, and compliant with applicable regulations. The switch must not break the yellow-green earth wire. The socket or switch must be easily reachable with the cooking hob fully installed.

GAS CONNECTION

The cooking hob is designed to operate with both natural gas (methane) and liquid gas (LPG), and can be easily converted from one type to another following the instructions given in the relative section of this booklet «Converting to a  different type of gas».
At factory the appliance has been pre-installed to natural gas.
Attention! Connection to the gas supply and converting to a different type of gas must be carried out by qualified technicians and in conformance with the requirements.
Depending on regional rules and regulations, may be used different (from mentioned) types of connections.
If the appliance is to operate with gas bottles (LPG), a pressure regulator conforming to the requirements.

Rigid pipe connection
Connection to the mains gas supply may be made via a metal pipe or via a rigid stainless steel pipe, or via a flexible steel-tipped hose 3 which is tightly attached to the fitting 2 (remove the plastic cap 1).
When connecting to LPG, use the fitting 4.
A service-adapter 5 is for gas service personal only. The gas connection with this adapter is prohibited.
The fittings 4 and 5 with seals are supplied with the appliance and comply with standards.
You must prevent the pipe from crushing, coming into contact with moving parts of the kitchen unit (for example, a drawer) and prevent access to any spaces which might become obstructed.

Attention! CHECK UP LEAKPROOFNESS of the connection to the gas supply pipe or gas cylinder using soap suds only. Spread soap suds on the joints, if there are bubbles, please close the valve and reconnect the hose until no bubbles.
Don’t use open flame – danger to life!
It is advisable to tighten the junctions by insulating teflon tape.
And if there is gas leak happens during using, please immediately shut off the gas source or call local gas sector service for help.
If the hob is to be combined with an oven, please check, that gas intake connection of the appliance has a “male thread”
When making the connection, take care not to apply stresses of any kind to the appliance.

CONVERSION TO A DIFFERENT TYPE OF GAS
Before converting the appliance for operation with a different gas type, check which type of gas it is currently set to operate with (adhesive label on appliance).
For the correct nozzle diameter, refer to the relative table in this booklet.
Conversion to a different gas type must be carried out by qualified technicians and in conformance with the requirements.
Conversion procedure:

• Disconnect the electrical power supply to the appliance,
• Turn the knobs in the null position.
• Replace the nozzles 1 with the corresponding type of gas to be used (see table «Nozzle table»).
• To adjust to the minimum, light the fire und turn the knob 2 in the position of minimal flame, then remove the knob of gas submission.
• Use a screwdriver on the screw placed on the tap 3.
• For LPG (butane/propane) screw tight the tap.

NOZZLE TABLE

| | Nozzle bore in mm
---|---|---
Burner| Rated load kW
G20/20| G30/30| G30/50
Turbo| 3,80| 1,35| 0,98| 0,77
Turbo*| 3,80| 1,49| 0,98| 0,77
Turbo**| 3,50| 1,45| 0,95| 0,77
Strong| 3,00| 1,15| 0,85| 0,75
Normal| 1,75| 0,97| 0,65| 0,58
Small| 1,00| 0,72| 0,50| 0,43
Burner| Rated load kW| Nozzle bore in mm
---|---|---
G25/20
Turbo| 3,60| 1,60
Strong| 3,00| 1,34
Normal| 1,50| 0,94
Small| 0,90| 0,72

• – for KG 6340 Turbo
  ** – for KG 6325… Turbo

RATED POWER

Model
KG 3351
KCG 3382
KG 6340 Turbo
KG 6350 Turbo,
KCG 6380 Turbo
KCG 6382 Turbo
KG 6357 Turbo
KCG 6387 Turbo
KCG 8382 Turbo
KG 6325 Turbo
KG 9325 Turbo
KCG 6383 Turbo
KCG 6335 *** Turbo
KG 9356 Turbo, KCG 9386 Turbo
KG 9357 Turbo

NSTALLATION OF THE HOBS

The regulations covering the installation, maintenance and operation of gas appliances for domestic use are applicable regulations.
This appliance is not provided with a combustion product discharge.
Installation and connection should be made in accordance with this regulation.
It is recommended that it be installed in sufficiently aerated places, in terms of the laws in force.
The quantity of air which is necessary for combustion must not be below 2,0 m³/h for each kW of installed power (See «Nozzle table»).
The appliance can be fitted into a working area as illustrated on the corresponding figure.
The installation space measurements are given in mm.
Make sure that surrounding materials are heat resistant.
Apply the seal provided over the whole of the area perimeter.

Attention! To install the appliance is not recommended the use of the silicone or other sealants and other adhesives besides the supplied mounting materials. If additional fastening materials and substances have been used, the  removing the device from the mounting niche in case of necessary service is provided by and at the expense of the owner. The manufacturer and the customer services are not responsible for damages of equipment and furniture because  of the disassembling.
Attention! Installation and electrical connection of the cooking hob must be made by a qualified expert only.
Attention! We Inform you that our devices which are the object of the present operating instructions are precertain exclusively for the domestic use. ![Kaiser KCGx Grand Chef 30cm Domino Gas Hob

• Figure 6](https://manuals.plus/wp-content/uploads/2023/08/Kaiser-KCGx-Grand- Chef-30cm-Domino-Gas-Hob-Figure-6.jpg)

WARNING: CRYSTAL HOBS
DO NOT TIGHTEN SCREW ‘A’ EXCESSIVELY, ONE TURN MAX WILL BE SUFFICIENT, AFTER CORRECTLY FITTING SHAFT ‘B’ INTO PLACE, AS SHOWN IN THE PICTURE. ENSURE THAT THE SUPPORTING SURFACE IS  PERFECTLY EVEN. FIT THE APPROPRIATE EXPANDED SEAL. CRYSTAL HOBS MUST NOT BE SUBJECTED TO STRAINS CAUSED BY UNEVEN SUPPORTING SURFACES.

SAFETY CONDITIONS

• Please, keep watch over children as long as the cooker hob is in operation. Children are unaware of operating rules. Hot gas burners, pans and pots with hot liquid on the grid above the burners can cause a skin-burn.
• Connection cords of electric appliances, e.g. a mixer, should not get in contact with hot parts of the cooker hob.
• Keep watching the cooker hob while frying: oils and fats can get inflamed due to overheating.
• If faults occur, further operation is not allowed until the appliance has been repaired by an authorized serviceman.
• Don’t turn on the valve of the gas inlet or gas cylinder before you make sure that the gas burners are switched off.
• Keep the burners clean. The overflow food or residues must be immediately removed after the burners get cold. Don’t put pans directly onto the burners.
• Don’t strike the knobs and the burners.
• Unauthorized persons are not allowed to carry on amendments or repair the cooker.
• Don’t blow out the flame of the burner.
• Users are not allowed to adjust the cookers to different gas type on their own, move the cooker to another place or make changes in the gas supply system. These operations can be carried on only by an authorized serviceman.
• Don’t let children and persons who are not informed about the operation instructions to operate the oven.
• The liquefied gas equipment is intended only for domestic use. This equipment should be checked every 2 years on security.
• This device is not intended for use by children. The nozzles, adapters and other small components and accessories can be swallowed by children and can cause a risk of strangulation. Do not allow children to play with the device or  close to it. During operation, the surface is heated. Children should not admit to it until it has cooled down.

In case of gas leak, it is not allowed: to strike a match, smoke, switch on and off an electric receiver (a door bell, a light switch) as well as use other electrical or mechanical appliances which can cause electric or chugging spark.
In this case, immediately shut off gas supply (turn off the valve of the gas cylinder or the switch which cuts off the connection to the gas supply), air the room and contact an authorized person.

• Don’t attach any cables to the gas appliance.
• If the gas leaking out of a no tight junction gets inflamed, immediately cut off the gas supply by turning off the valve of the gas cylinder or the switch which disconnects gas supply).
• In case of damage: air the room, disconnect the appliance from the power supply and repair the fault.
• If the gas leaking out of the no tight junction of the gas cylinder gets inflamed, wrap the cylinder with a wet blanket to extinguish the flame and turn off the valve (stopcock) of the gas cylinder. Further use of the damaged gas cylinder is not allowed.
• If you don’t use the gas cooker hob for a few days, disconnect it from the gas supply by turning off the stop valve. In case of a gas cylinder, turn off the stopcock every time after the use.

The gas supply should provide the gas cooker hob with the type of gas it has been adjusted to in plant. Information about the gas type which the gas cooker hob has been adjusted to is registered on the data plate.

GAS COOKING HOB

Attention! The use of a gas cooking hob results the production of heat, moisture and products of combustion in the room in which it is installed. Ensure that the kitchen is well ventilated especially when the hob is in operation: keep  natural ventilation apertures open or install a mechanical ventilation device (cooker hood). Prolonged intensive use of the appliance may require additional ventilation. Open a window or increase the power of the cooker hood.

USAGE

The cooking zones control is achieved by means of knobs set up on the control panel of the cooker.(See a section “Equipment”)
Correctly adjusted burners have a light blue flame with a distinct internal cone.
Flame volume is adjusted by rotary switches: burner is off (“gas supply is stopped”) big flame small flame (“sparing”)
Rotary switches ensure gradual setting of flame volume.
All gas cooking hob are provided with the system of electrical ignition operated by means of knobs or electrical ignition button.

To switch on a gas burner:
Models with the system of electrical ignition

• press the corresponding rotary switch of the selected burner against the stop and turn it to the left up to the position big flame

• keep the switch pressed till the burner ignites
  The electric spark between the ignition plug and the burner provides the ignition of the burner itself.

• after the burner has ignited, let the rotary switch go and select the required flame volume (e.g. “sparing”).

• to switch off the burner after the food is ready turn on the rotary switch to the right (position “gas supply is stopped”).

For models with a thermoelectric safety system, the burner is ignited as in the various cases described above; keeping the knob fully pressed on the position big flame for approximately 3-5 seconds to activate the control system.
After releasing the knob, make sure the burner is actually lit.
It is recommend the use of pots and pans with a diameter matching that of the burner, thus preventing the flame from escaping from the bottom part and surrounding the pot. The flame must not touch the sides of the pan.
Do not use small pots and pans on large burners.

Always centre the pan over the burner, not to one side. Otherwise it could tip over.
Do not use damaged pans, which do not sit evenly on the hob. Pans may tip over. Only use pans with a flat base.
Do not place large pans on the burners near the control knobs. These may be damaged by the very high temperatures.
Do not leave any empty pots or pans on the fire
When cooking is finished, it is also a good norm to close the main gas pipe tap and/or cylinder.

IMPORTANT!!! Fire danger The overheated fats or oils are flammable.
Watch the cooking processes with fats or oils carefully. Never use water to put the fire out if oil or fats do catch fire. Put the fire out by covering the pan with a lid and switching off the hob.

CARE AND ATTENDANCE

Current maintenance
Prior to any operation, disconnect the appliance from the electrical system. For long-life to the equipment, a general cleaning operation must take place periodically, bearing in mind the following:

• The glass, steel and/ or enameled parts must be cleaned with suitable non-abrasive or corrosive products (found on the market). Avoid chlorine-base products (bleach, etc.)
• Avoid leaving acid or alkaline substances on the working area (vinegar, salt, lemon juice, etc.)
• The wall baffle and the small covers (mobile parts of the burner) must be washed frequently with boiling water and detergent, taking care to remove every possible encrustation. Dry carefully and check that none of the burner holes  is fully or partially clogged
• The electrical parts are cleaned with a damp cloth and are lightly greased with lubricating oil when still warm
• The stainless steel grids of the working area, after having been heated, take on a bluish tint which does not deteriorate the quality.

Cleaning of the taps must be carried out by qualified personnel, who must be consulted in case of any functioning anomaly.
Check periodically the state of conservation of the flexible gas feed pipe. In case of leakage, call immediately the qualified technicians for its replacement.

Cyclic inspection

Besides the current maintenance, the user should ensure:

• alternate check and maintenance of hob elements and assemblies,
• cyclic inspection by the customer service once in two years after the warranty has expired.
• repair of faults.

In case of a damage:

• switch off all hob operating functions (gas burner, electrical cooking zone)
• disconnect the appliance from the power supply
• contact the Customer Centre or another authorized organization to order the servicing.

Note! Care and servicing as well as all kind of reparations are to be carried out by authorized personnel only.

IMPORTANT!!!
The user is responsible for good working order and correct operation of the appliance. If the customer service is called because of an operating mistake, the servicing costs are carried by the user even if the warranty is still valid.
Damages caused by non-observance of the given instruction are not approved.

RESPECT FOR THE ENVIRONMENT
The documentation provided with this oven has been printed on chlorine free bleached paper or recycled paper to show respect for the environment.
The packaging has also been designed to avoid environmental impact. Packaging material is ecological and can be re-used or recycled.
By recycling the packaging, you will help save raw materials as well as reducing the bulk of domestic and industrial waste.

Disposing of the packaging
Please dispose of the packaging that came with your appliance in an environmentally friendly way.
Recycling in this way saves on resources and cuts down on waste.

Disposing of old appliances
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

WARRANTY CONDITIONS FOR HOME APPLIANCES

1. The warranty for a broken part is valid for the full period of 24 months from the day of purchase.
2. The manufacturer only covers the servicing in the event of a manufacturer fault, such as but not limited to: inappropriate design, installation by technician, defective materials.
3. This warranty applies only to products used for the following purposes: non-commercial, personal, family, residential, or For anything outside of these purposes, the warranty is only valid for 4 months from the date of purchase of the products.
4. Repairs that qualify under this warranty guarantee are completely free including the cost of labour, and materials, transportation is determined by the relevant Kaiser servicing centre.
5. Any questions or queries on the quality of the product will be assessed only after our servicing company checks the Any conclusions will only be reached based on the outcome of a servicing report.
6. The product will only be exchanged within the warranty period in the situation that the servicing expert concludes that the product cannot be repaired or if the same product requires parts changed three times in total within the warranty period.
7. In case of unnecessary or unjustified demands for customer service, we charge for our service the usual time consumption and transportation fees. Before you contact our customer service, please check whether it’s a defect or error of a product or or mistake of maintenance. Please take the time to communicate with the relevant Kaiser service center.
8. Installation of the device should only be carried out by qualified professional persons. The customer is required to provide appropriate justification. Otherwise there is no entitlement to the grant of a guarantee.
9. Only the distributor selling the products has the right to exchange the defected product for a new one. 1 O. Liability under this warranty is limited to, unless otherwise specified by law is all referred to these above obligations.

WARRANTY NOT VALID WHEN:

1. In the event of our products being damaged or experiencing some kind of fault from transport damage, due to incorrect installation by other than trained Kaiser technician or taking improper care of the products, connecting to the wrong power supply, the use of non-recommended cleaning agents and detergents. Any failure to comply with the instructions for operational use or if the product has been repaired or modified or installed by the customer and changed or removed the serial number will not qualify for the warranty conditions.
2. Products being serviced by an unauthorized servicing company will not be valid for warranty.
3. Product failures caused by reasons independent of the manufacturer, such as fluctuations in the power supply, external events such as nature or natural disasters, fire, insects or domestic and wild animals will not comply with the warranty conditions.
4. If the glass or the ceramic glass on a product is broken or defected after installation, the customer will be held liable.
5. Any damage scratches, cracks, and external mechanical faults caused during the operation by the customer.
6. The damage of certain parts being caused by normal wear and tear such as (lamps, filters, etc.).
7. Other external factors causing damage such as adjusting the products and cleaning.
8. Any other damage caused by the fault of the user and which is not linked to faults caused by the manufacturer will not comply with the warranty agreement.

The unearthed devices are potentially dangerous.
The manufacturer accepts no liability for damages which have caused by improper use, the incorrect installation, operation, application or maintenance.

ELESCO EUROPA GmbH
The Service Solution Company
Langer Acker 35, 30900 Wedemark, Deutschland
Tel.: +49 (0) 511-5151 3370
Fax.: +49 (0) 511 5343 0910
E-Mail: kaiser@elesco-europa.com
Internet: www.elesco-europa.com

http://www.elesco-europa.com

Reduction of environmental impact

Information on reducing the environmental impact from cooking and non- destructive disassembly.
The following calculation and measurement methods were used to determine the results and in accordance with the requirements for labeling in terms of energy consumption and in terms of ecodesign requirements: Directives of the European Parliament and of the Council – Regulation (EU) No. 65/2014 and No. 66/2014.
EN 50564:2011 – Electrical and electronic household and office equipment – Measurement of low power consumption.
Information on reducing the environmental impact (e.g. energy consumption) from cooking in accordance with Annex I, No. 2 of Regulation (EU) No. 66/2014 with a regard to setting ecodesign requirements for household ovens, hobs  and cooker hoods.

• Use baking pans and trays with dark and matte surfaces, because they conduct heat better
• Open the oven door during cooking only when necessary
• Preheat the cooking chamber only when necessary according to the recipe
• Always select the lowest recommended temperature for cooking temperatures
• Switch the oven to minimum temperature shortly before the end of the cooking time to use the residual heat
• To ensure energy efficiency, switch all buttons (temperature, interior light and program) to “0/Off” when the oven is not in use
• Remove any soiling immediately, otherwise the cleaning effort may increase
• Use biological cleaners to clean the oven

Information for professional users for dismantling according to Annex I, No. 2 of Regulation (EU) No. 66/2014
Information on non-destructive disassembly for maintenance purposes

• Disassembly for maintenance purposes can only be performed for the oven door (see chapter “Disassembling the oven door” p.71).
• Disassembly for maintenance purposes is not foreseen.
• For repair and replacement of defective parts, please contact the customer service.
• Accumulators are not included.

Disassembly information related to recycling, recovery and disposal at the end of the life of the device.

• Dismantling of devices with gas connection may only be carried out by a licensed gas and water installer.
• Dismantling of devices with electrical connection should be performed by a licensed electrician.

For recycling and resource recovery, specify the device:

• municipal collection point run by the public waste disposal authorities
• manufacturer’s own waste disposal company that offers a take-back system
• local electrical retailer who voluntarily takes back electrical equipment.

For information on the energy efficiency index for each oven compartment, the dimensions of the appliance, the number of oven compartments, the heat source per oven compartment and the volume per oven compartment please refer  to the data sheet, attached to the user manual.

EG Declaration of Conformity
This is to confirm that all built-in cooking hobs electrograms
Brand:
Type: KG 33…, KG 43…, KG 63…, KG 93…, KCG 33…, KCG 43…, KCG 63…, KCG 83…, KCG 93…*

…model number,
= colour
comply with the regulations of the European Directives.
The conformity of the designated product with:

• LVD (Low Voltage Directive) und CE 2014/30/EU: EMC (Electromagnetic Compatibility);
• LVD (Low Voltage Directive) and CE 2014/30/EU: EMC (Electromagnetic Conformity);
• Commission Regulation (EU) No 65/2014 of 1. October 2013 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to the energy labelling of domestic ovens and range hoods;
• Commission Regulation (EU) No 66/2014 of 14. January 2014 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for domestic ovens, hobs and range hoods is demonstrated by full compliance with the following European standards:

EN 60335-1:2012
EN 60335-2-102:2006+A1:2010
EN 62233:2008
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2013
EN 60350-1:2013+A11:2014
EN 50564:2011
EN 61591:1997+A1:2006+A2:2011+A11:2014
EN 50564:2011
EN 15181-2017
Kaiser
OLAN-Haushaltsgeräte e.K.
28.02.2020
N. Liskovoj
Department Manager
The manufacturer declines all responsibility for possible mistakes and typing errors and reserves the right to make in design and construction of our own products those changes which do not touch negative influence upon the qualities  and properties without a preliminary notification.

OLAN-Haushaltsgeräte • Berlin • Germany
www.kaiser-olan.de

References

• Europa.com is For Sale | BrandBucket
• Бытовая техника Kaiser - Официальное представительство, интернет-магазин
• ELESCO EUROPA GmbH – Reparatur – Service – Installation – Wartung – Ersatzteile
• ESECO GmbH | Das Netzwerk für maßgeschneiderte Servicelösungen in Österreich
• Kaiser offizielle Webseite – Kaiser offizielle Webseite
• SFG | Société française de garantie
• Universal Service Provider

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>