PROTOCOL AEROFLUX Folding Drone with Live Streaming Camera Instruction Manual
- June 12, 2024
- PROTOCOL
Table of Contents
PROTOCOL AEROFLUX Folding Drone with Live Streaming Camera
Product Information
- Product Name: Folding Drone with Live Streaming Camera
- Model Number: SMPTC-90008
- Supplier: Samsonico USA LLC
- Address: 4925 Westin Park Dr. Conway, Arkansas, 72034, USA
- Manufactured in: China
Product Usage Instructions
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.
- Ensure compliance with FCC Rules:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired interference.
- To mitigate interference, you can:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Additional Battery Information and Warnings:
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.
- To fold the drone:
- Follow the instructions provided by the manufacturer.
- For live streaming camera usage:
- Refer to the instruction manual provided by the manufacturer.
Please read this manual carefully before operation and keep it properly for future reference.
DRONE DIAGRAM
- Upper Body
- Lower Body
- Propeller
- Arm
- Battery
- Motor
- camera
ACCESSORIES INCLUDED
PRE-FLIGHT PREPARATION
FLIGHT ENVIRONMENT
OPEN THE ARMS
OPENING STEPS
Open the front arm(close to the camera)
Open the back arm
ASSEMBLING BLADE GUARDS
ASSEMBLING PROPELLERS
Align the blades with the motor shaft and install them, the arm letter must be consistent with the blade letter. Tighten the screw clockwise.
BATTERY CHARGING FOR DRONE
- Remove the lithium battery from the bottom of the drone
- Connect the USB charging cable with the charging interface of the lithium battery.
A BATTERY INSTRUCTIONS
- A body injury or property loss. Users must be aware of the risks and take full responsibility for using batteries improperly.
- If battery leakage occurs, please avoid contacting your eyes or skin with electrolytes. Once it happens, please wash your eyes with clean water and seek medical care immediately.
- Please remove the plug immediately if you sense any unusual smell noise or smoke!
Battery Charging
- Please use the charger from the original factory to ensure safe
- Do not charge the outworn battery.
- Do not overcharge the battery. Please unplug the charger once fully charged.
- Do not charge the battery next to inflammable, such as carpet, timber floor, or wood furniture, or on the surface of electro-conductive objects.
- Please always keep an eye on the battery when charging.
- Do not charge the battery which has not cooled down yet.
- The charging temperature should be between 0°to 40°C.
Battery Recycling
- Do not dispose of the battery as daily rubbish. Please familiarize yourself with the local garbage disposal method and dispose of it according to the special requirement.
ADDITIONAL BATTERY INFORMATION AND WARNINGS
We recommend the use of alkaline batteries only Always connect the batter to the correct polarity + to + and – to -). Do not throw away used batteries in the garbage, use recycling centers or dispose of them at a recycling depot. Do not dispose of batteries in a fire, they may leak or explode. Univ uses the batteries special. batteries should be replaced by adults. Check batteries regularly for any leaks. Remove empty batteries. Do not recharge Non- rechargeable batteries. store charging remove rechargeable batteries. rechargeable batteries must be character under adult supervision only. Do not mo old and new batteries and Do not mix alkaline, standard carbon zine or etc. patents. connection terminal must not be short-circuited. Subject to technical change and change of color. Please k8ео this information for future reference
“This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference. This device must accept any interference recarved inc voting
interference that may cause undesired “CAUTION: Changes or modifications
not expressly approved by the party responsible for the compliance cour void
the Users autonomy to operate we equipment
“Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part h or the CO Rules. Inese limes
are designed to prove reasonable protection against! harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
were is no guarantee that war interference did not occur in a particular
installation. it this equipment does cause harmful interference to radio or
television reception. which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reonent or relocato me recavino diverina.
- Increase the separation between the equipment and the receiver
- Connect the equipment to an outlet on a circuit deterrent from that to which the receiver is connected
- Consult the dealer or an experienced radio V technician or he
Product name: AEROFLUX FOLDING DRONE WITH LIVE STREAMING CAMERA
- Model NO- SMPTC.OnCOS
- Supplier: SAMSONICO USA LLC
- Address 4C25 WESTIN PARK
- DR.CONWAY ARKANSAS, 72034, USA FC
- MADE IN CHINA
REMOTE CONTROL DIAGRAM
- Left Stick
- (Throttle Up/Down
- Left/Right Turn)
- Right Stick
- (Forward/Backward
- Left/Right Bank)
- Photo Video
- Forward Trim
- Backward Trim
- Power On/Off
- Headless Mode
- right On/Off
- One keymapping
- Left Trim Right Trim
- Speed Flips
- Phone Holder-Pull up to install phone
INSTALLING REMOTE BATTERIES
Open the remote control battery cover Remote control battery installation
AAA batteries
Open the battery cover and insert the 3 AAA batteries correctly according to
the electrode instructions.(Batteries not included)
Notes
- Make sure the batteries are loaded correctly according to the polarity indications on the battery compartment.
- Please do not mix old and new batteries together.
- Please do not mix different types of batteries together.
TURNING ON AND SYNCING THE DRONE &REMOTE
- Turn on the drone and place it on a level surface. Then turn on the remote. The indicator light of the remote and the drone’s LED will flash.
- Push the throttle up and then down. The drone will beep twice and the lights will go steady. Syncing is complete.
CALIBRATING THE DRONE
If the aircraft cannot rise vertically after taking off, it can be corrected
by pulling the left and right joysticks into a lower outer corner at the same
time. The remote will beep and the indicator lights will flash quickly and
then go steady. Calibration is complete.
START YOUR FLIGHT
Idle Mode: Push the throttle up and release. The drone’s blades will spin but
the drone will not take off. The blades will stop spinning after 5-6 seconds
of inactivity.
One-key Take-off
Press the “One-key Take-off” button, and the drone blades rotate and
automatically fly to a height of 1.5 meters
Basic Flight
Use the left joystick to control the flight altitude and turn the left/right,
and the right joystick to control the forward, backward, left, and right side
flight directions.
360° FLIPS
When the drone reaches more than 3 meters high, press the Flip button and move
the right joystick in the desired direction. The drone will rotate in that
direction. Right joystick Fllp Backward
Headless Mode
Users have the option to exit the default orientation (the nose is the front
of the drone). In Headless Mode, users can operate the drone without
orientation. Regardless of where the drone is pointing, it will turn left or
right according to the remote’s command. Turn on the drone and remote and
calibrate. Press the Headless Mode key. The remote will beep once and engage.
Press again to leave Headless Mode. The remote will beep again and return to
the default orientation
Speed Mode
When the aircraft takes off, it is by default in the low-speed mode (3-geared
switching); gently press the speed button. A “beep” sound for low-speed gear,
two “beep” sounds for medium-speed gear and three “beep” sound for high-speed
gear.
Hover
When you release the left joystick (throttle) after the ascent/descent action,
the drone will hover at a certain height.
Left joystick
TRIM FUNCTION
When the aircraft drifts in different directions, you can use the trim to correct it. When the aircraft leaves the ground and the aircraft deviates to the back/forward, press the Forward/ Backward trim key to trim. When the aircraft leaves the ground and the aircraft deviates to the left/right, press the Right/Left trim key to adjust. The remote will emit a long beep when the drone is centered.
- Forward/ BackwardTrim
- Left/Right Bank Trim
Notes
When the drone is within 30cm of the ground, it will be affected by the blade
vortex and become unstable. This is the “ground effect The lower the drone is,
the greater the effect will be.
FAQ
APP INSTRUCTIONS & PHOTO/VIDEO INSTALLING AND CONNECTING TO THE APP
- The App is available in both Apple and Android App stores Search ” Protoco AeroF ux ano comics te Aço to yout
- rum on the crone and the remote.
- Once it turned on. AeroF UX will transfer a WiFi single make sure your smartphone is connected to the Siang
- Open the App and press ‘START.
- will show and live stream the camera view.
The App contains a guide for icons and functions, including photos and videos, wlin the App. -or inquiries
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>