PROTOCOL RS485 Modbus And Lan Gateway User Guide

PROTOCOL RS485 Modbus And Lan Gateway

Specifications

• Communication Protocols: MODBUS ASCII/RTU, MODBUS TCP
• Supported Interfaces: RS485 MODBUS, LAN
• Maximum Slaves Supported: Up to 247
• MODBUS TCP Port: 502
• Frame Structure:
  • ASCII Mode: 1 Start, 7 Bit, Even, 1 Stop (7E1)
  • RTU Mode: 1 Start, 8 Bit, None, 1 Stop (8N1)
  • TCP Mode: 1 Start, 7 Bit, Even, 2 Stop (7E2)

FAQ

• What is the purpose of the MODBUS Communication Protocol?
• The MODBUS protocol facilitates communication between a master device and multiple slave devices, enabling data exchange in industrial automation systems.
• How many slaves can be connected using the MODBUS protocol?
• The MODBUS protocol supports up to 247 slaves connected in a bus or star network configuration.
• How can I change the slave address in MODBUS ASCII/RTU mode?
• To change the slave address in MODBUS ASCII/RTU mode, refer to the user manual for instructions on configuring the counter’s logical number.

Limitation of Liability
The Manufacturer reserves the right to modify the specifications in this manual without previous warning. Any copy of this manual, in part or in full, whether by photocopy or by other means, even of an electronic nature, without the manufacturer giving written authorization, breaches the terms of copyright and is liable to prosecution.
It is forbidden to use the device for different uses other than those for which it has been devised, as inferred in this manual. When using the features in this device, obey all laws and respect the privacy and legitimate rights of others.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL THE MANUFACTURER BE LIABLE FOR CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH SAID PRODUCT AND THE MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OBBLIGATION OR LIABILITY OTHER THAN SUCH AS IS EXPRESSLY SET FORTH HEREIN.
All trademarks in this manual are the property of their respective owners.
The information contained in this manual is for information purposes only, is subject to changes without previous warning and cannot be considered binding for the Manufacturer. The Manufacturer assumes no responsibility for any errors or incoherence possibly contained in this manual.

DESCRIPTION

MODBUS ASCII/RTU is a master-slave communication protocol, able to support up to 247 slaves connected in a bus or a star network. The protocol uses a simplex connection on a single line. In this way, the communication messages move on a single line in two opposite directions.
MODBUS TCP is a variant of the MODBUS family. Specifically, it covers the use of MODBUS messaging in an “Intranet” or “Internet” environment using the TCP/IP protocol on a fixed port 502.
Master-slave messages can be:

• Reading (Function codes $01, $03, $04): the communication is between the master and a single slave. It allows to read information about the queried counter
• Writing (Function code $10): the communication is between the master and a single slave. It allows to change the counter settings
• Broadcast (not available for MODBUS TCP): the communication is between the master and all the connected slaves. It is always a write command (Function code $10) and requires logical number $00

In a multi-point type connection (MODBUS ASCII/RTU), a slave address (called also logical number) allows to identification of each counter during the communication. Each counter is preset with a default slave address (01) and the user can change it.
In case of MODBUS TCP, the slave address is replaced by a single byte, the Unit identifier.

Communication frame structure – ASCII mode
Bit per byte: 1 Start, 7 Bit, Even, 1 Stop (7E1)

type
ERROR CHECK| 2 chars| Error check (LRC)
END FRAME| 2 chars| Carriage return – line feed (CRLF) pair ($0D & $0A)

Communication frame structure – RTU mode
Bit per byte: 1 Start, 8 Bit, None, 1 Stop (8N1)

condition)
ADDRESS FIELD| 8 bits| Counter logical number
FUNCTION CODE| 8 bits| Function code ($01 / $03 / $04 / $10)
DATA FIELD| n x 8 bits| Data + length will be filled depending on the message type
ERROR CHECK| 16 bits| Error check (CRC)
END FRAME| 4 chars idle| At least 4 characters’ time of silence between frames

Communication frame structure – TCP mode
Bit per byte: 1 Start, 7 Bit, Even, 2 Stop (7E2)

client
PROTOCOL ID| 2 bytes| Zero for MODBUS TCP
BYTE COUNT| 2 bytes| Number of remaining bytes in this frame
UNIT ID| 1 byte| Slave address (255 if not used)
FUNCTION CODE| 1 byte| Function code ($01 / $04 / $10)
DATA BYTES| n bytes| Data as response or command

LRC Generation

The Longitudinal Redundancy Check (LRC) field is one byte, containing an 8–bit binary value. The LRC value is calculated by the transmitting device, which appends the LRC to the message. The receiving device recalculates an LRC during receipt of the message and compares the calculated value to the actual value it received in the LRC field. If the two values are not equal, an error results. The LRC is calculated by adding together successive 8–bit bytes in the message, discarding any carries, and then two’s complementing the result. The LRC is an 8–bit field, therefore each new addition of a character that would result in a value higher than 255 decimal simply ‘rolls over’ the field’s value through zero. Because there is no ninth bit, the carry is discarded automatically.
A procedure for generating an LRC is:

1. Add all bytes in the message, excluding the starting ‘colon’ and ending CR LF. Add them into an 8–bit field, so that carries will be discarded.
2. Subtract the final field value from $FF, to produce the ones–complement.
3. Add 1 to produce the twos–complement.

Placing the LRC into the Message
When the 8–bit LRC (2 ASCII characters) is transmitted in the message, the high–order character will be transmitted first, followed by the low–order character. For example, if the LRC value is $52 (0101 0010):

Colon

‘:’

| Address| Func| Data

Count

| Data| Data| ….| Data| LRC

Hi ‘5’

| LRC

Lo‘2’

| CR| LF
---|---|---|---|---|---|---|---|---|---|---|---

C-function to calculate LRC

CRC Generation
The Cyclical Redundancy Check (CRC) field is two bytes, containing a 16–bit value. The CRC value is calculated by the transmitting device, which appends the CRC to the message. The receiving device recalculates a CRC during receipt of the message and compares the calculated value to the actual value it received in the CRC field. If the two values are not equal, an error results.
The CRC is started by first preloading a 16–bit register to all 1’s. Then a process begins of applying successive 8–bit bytes of the message to the current contents of the register. Only the eight bits of data in each character are used for generating the CRC. Start and stop bits, and the parity bit, do not apply to the CRC.
During generation of the CRC, each 8–bit character is exclusive ORed with the register contents. Then the result is shifted in the direction of the least significant bit (LSB), with a zero filled into the most significant bit (MSB) position. The LSB is extracted and examined. If the LSB was a 1, the register is then exclusive ORed with a preset, fixed value. If the LSB was a 0, no exclusive OR takes place.
This process is repeated until eight shifts have been performed. After the last (eighth) shift, the next 8–bit character is exclusive ORed with the register’s current value, and the process repeats for eight more shifts as described above. The final contents of the register, after all the characters of the message have been applied, is the CRC value.
A calculated procedure for generating a CRC is:

1. Load a 16–bit register with $FFFF. Call this the CRC register.
2. Exclusive OR the first 8–bit byte of the message with the low–order byte of the 16–bit CRC register, putting the result in the CRC register.
3. Shift the CRC register one bit to the right (toward the LSB), zero–filling the MSB. Extract and examine the LSB.
4. (If the LSB was 0): Repeat Step 3 (another shift). (If the LSB was 1): Exclusive OR the CRC register with the polynomial value $A001 (1010 0000 0000 0001).
5. Repeat Steps 3 and 4 until 8 shifts have been performed. When this is done, a complete 8–bit byte will have been processed.
6. Repeat Steps 2 through 5 for the next 8–bit byte of the message. Continue doing this until all bytes have been processed.
7. The final content of the CRC register is the CRC value.
8. When the CRC is placed into the message, its upper and lower bytes must be swapped as described below.

Placing the CRC into the Message
When the 16–bit CRC (two 8–bit bytes) is transmitted in the message, the low- order byte will be transmitted first, followed by the high-order byte.
For example, if the CRC value is $35F7 (0011 0101 1111 0111):

Addr| Func| Data

Count

| Data| Data| ….| Data| CRC

lo F7

| CRC

Hi 35

---|---|---|---|---|---|---|---|---

CRC generation functions – With Table

All of the possible CRC values are preloaded into two arrays, which are simply indexed as the function increments through the message buffer. One array contains all of the 256 possible CRC values for the high byte of the 16–bit CRC field, and the other array contains all of the values for the low byte. Indexing the CRC in this way provides faster execution than would be achieved by calculating a new CRC value with each new character from the message buffer.

CRC generation functions – Without Table

READING COMMAND STRUCTURE

• In the case of a module combined with a counter: The master communication device can send commands to the module to read its status and setup or to read the measured values, status and setup relevant to the counter.
• In the case of the counter with integrated communication: The master communication device can send commands to the counter to read its status, setup and measured values.
• More registers can be read, at the same time, sending a single command, only if the registers are consecutive (see Chapter 5). According to the MODBUS protocol mode, the read command is structured as follows.

Modbus ASCII/RTU
Values contained both in Query or Response messages are in hex format.
Query example in case of MODBUS RTU: 01030002000265CB

Response example in case of MODBUS RTU: 01030400035571F547

Modbus TCP
Values contained both in Query or Response messages are in hex format.
Query example in case of MODBUS TCP: 010000000006010400020002

Response example in case of MODBUS TCP: 01000000000701040400035571

Floating Point as per IEEE Standard

• The basic format allows an IEEE standard floating-point number to be represented in a single 32-bit format, as shown below:

• where S is the sign bit, e’ is the first part of the exponent and f is the decimal fraction placed next to 1. Internally the exponent is 8 bits in length and the stored fraction is 23 bits long.

• A round-to-nearest method is applied to the calculated value of floating point.

• The floating-point format is shown as follows:

NOTE: Fractions (decimals) are always shown while the leading 1 (hidden bit) is not stored.

Example of conversion of value shown with floating point
The value read with the floating point:
45AACC00(16)
Value converted in binary format:

WRITING COMMAND STRUCTURE

• In the case of a module combined with a counter: The master communication device can send commands to the module to program itself or to program the counter.
• In the case of a counter with integrated communication: The master communication device can send commands to the counter to program it.
• More settings can be carried out, at the same time, sending a single command, only if the relevant registers are consecutive (see chapter 5). According to the used MODBUS protocol type, the write command is structured as follows.

Modbus ASCII/RTU
Values contained both in Request or Response messages are in hex format.
Query example in case of MODBUS RTU: 011005150001020008F053

Response example in case of MODBUS RTU: 01100515000110C1

Modbus TCP
Values contained both in Request or Response messages are in hex format.
Query example in case of MODBUS TCP: 010000000009011005150001020008

Response example in case of MODBUS TCP: 010000000006011005150001

EXCEPTION CODES

• In case of module combined with counter: When the module receives a not-valid query, an error message (exception code) is sent.
• In the case of the counter with integrated communication: When the counter receives a not-valid query, an error message (exception code) is sent.
• According to the MODBUS protocol mode, possible exception codes are as follows.

Modbus ASCII/RTU
Values contained in Response messages are in hex format.
Response example in case of MODBUS RTU: 01830131F0

Exception codes for MODBUS ASCII/RTU are following described:

• $01 ILLEGAL FUNCTION: the function code received in the query is not an allowable action.
• $02 ILLEGAL DATA ADDRESS: the data address received in the query is not allowable (i.e. the combination of register and transfer length is invalid).
• $03 ILLEGAL DATA VALUE: a value contained in the query data field is not an allowable value.
• $04 ILLEGAL RESPONSE LENGTH: the request would generate a response with a size bigger than that available for MODBUS protocol.

Modbus TCP
Values contained in Response messages are in hex format.
Response example in case of MODBUS TCP: 010000000003018302

Exception codes for MODBUS TCP are following described:

• $01 ILLEGAL FUNCTION: the function code is unknown by the server.
• $02 ILLEGAL DATA ADDRESS: the data address received in the query is not an allowable address for the counter (i.e. the combination of register and transfer length is invalid).
• $03 ILLEGAL DATA VALUE: a value contained in the query data field is not an allowable value for the counter.
• $04 SERVER FAILURE: the server failed during the execution.
• $05 ACKNOWLEDGE: the server accepted the server invocation but the service requires a relatively long time to execute. The server therefore returns only an acknowledgement of the service invocation receipt.
• $06 SERVER BUSY: the server was unable to accept the MB request PDU. The client application has the responsibility of deciding if and when to resend the request.
• $0A GATEWAY PATH UNAVAILABLE: the communication module (or the counter, in case of the counter with integrated communication) is not configured or cannot communicate.
• $0B GATEWAY TARGET DEVICE FAILED TO RESPOND: the counter is not available in the network.

GENERAL INFORMATION ON REGISTER TABLES

NOTE: Highest number of registers (or bytes) which can be read with a single command:

• 63 registers in ASCII mode
• 127 registers in RTU mode
• 256 bytes in TCP mode

NOTE: Highest number of registers which can be programmed with a single command:

• 13 registers in ASCII mode
• 29 registers in RTU mode
• 1 register in TCP mode

NOTE: The register values are in hex format ($).

+/-

| Positive or negative sign on the read value.

The sign representation changes according to the communication module or counter model:

Sign Bit Mode : If this column is checked, the read register value can have a positive or negative sign. Convert a signed register value as shown in the following instructions:

The Most Significant Bit (MSB) indicates the sign as follows: 0=positive (+), 1=negative (-). Negative value example:

MSB

$8020 = 1 000000000100000 = -32

| hex |                     bin                 | dec |

2’s Complement Mode : If this column is checked, the read register value can have a positive or negative

sign. The negative values are represented with 2’s complement.

INTEGER

| INTEGER register data.

It shows the Unit of measure, the RegSet type the corresponding Word number and the Address in hex format. Two RegSet types are available:

RegSet 0: even / odd word registers.

RegSet 1: even word registers. Not available for LAN GATEWAY modules.

Available only for:

▪     Counters with integrated MODBUS

▪     Counters with integrated ETHERNET

▪     RS485 modules with firmware release 2.00 or higher To identify the RegSet in use, please refer to $0523/$0538 registers.

IEEE| IEEE Standard Register data.

It shows the Unit of measure, the Word number and the Address in hex format.

REGISTER AVAILABILITY BY MODEL

| Availability of the register according to the model. If checked (●), the register is available for the

corresponding model:

3ph 6A/63A/80A SERIAL: 6A, 63A and 80A 3phase counters with serial communication.

1ph 80A SERIAL: 80A 1phase counters with serial communication.

1ph 40A SERIAL: 40A 1phase counters with serial communication.

3ph integrated ETHERNET TCP: 3phase counters with integrated ETHERNET TCP communication.

1ph integrated ETHERNET TCP: 1phase counters with integrated ETHERNET TCP communication.

LANG TCP (according to model): counters combined with LAN GATEWAY module.

DATA MEANING| Description of data received by a response of a reading command.
PROGRAMMABLE DATA| Description of data that can be sent for a writing command.

READING REGISTERS (FUNCTION CODES $03, $04)

U1N| Ph 1-N Voltage|  | 2| 0000| 2| 0000| mV| 2| 1000| V| ●|  |  | ●|  | ●
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
U2N| Ph 2-N Voltage|  | 2| 0002| 2| 0002| mV| 2| 1002| V| ●|  |  | ●|  | ●
U3N| Ph 3-N Voltage|  | 2| 0004| 2| 0004| mV| 2| 1004| V| ●|  |  | ●|  | ●
U12| L 1-2 Voltage|  | 2| 0006| 2| 0006| mV| 2| 1006| V| ●|  |  | ●|  | ●
U23| L 2-3 Voltage|  | 2| 0008| 2| 0008| mV| 2| 1008| V| ●|  |  | ●|  | ●
U31| L 3-1 Voltage|  | 2| 000A| 2| 000A| mV| 2| 100A| V| ●|  |  | ●|  | ●
U∑| System Voltage|  | 2| 000C| 2| 000C| mV| 2| 100C| V| ●| ●| ●| ●| ●| ●
A1| Ph1 Current| ●| 2| 000E| 2| 000E| mA| 2| 100E| A| ●|  |  | ●|  | ●
A2| Ph2 Current| ●| 2| 0010| 2| 0010| mA| 2| 1010| A| ●|  |  | ●|  | ●
A3| Ph3 Current| ●| 2| 0012| 2| 0012| mA| 2| 1012| A| ●|  |  | ●|  | ●
AN| Neutral Current| ●| 2| 0014| 2| 0014| mA| 2| 1014| A| ●|  |  | ●|  | ●
A∑| System Current| ●| 2| 0016| 2| 0016| mA| 2| 1016| A| ●| ●| ●| ●| ●| ●
PF1| Ph1 Power Factor| ●| 1| 0018| 2| 0018| 0.001| 2| 1018| –| ●|  |  | ●|  | ●
PF2| Ph2 Power Factor| ●| 1| 0019| 2| 001A| 0.001| 2| 101A| –| ●|  |  | ●|  | ●
PF3| Ph3 Power Factor| ●| 1| 001A| 2| 001C| 0.001| 2| 101C| –| ●|  |  | ●|  | ●
PF∑| Sys Power Factor| ●| 1| 001B| 2| 001E| 0.001| 2| 101E| –| ●| ●| ●| ●| ●| ●
P1| Ph1 Active Power| ●| 3| 001C| 4| 0020| mW| 2| 1020| W| ●|  |  | ●| | ●
P2| Ph2 Active Power| ●| 3| 001F| 4| 0024| mW| 2| 1022| W| ●|  |  | ●| | ●
P3| Ph3 Active Power| ●| 3| 0022| 4| 0028| mW| 2| 1024| W| ●|  |  | ●| | ●
P∑| Sys Active Power| ●| 3| 0025| 4| 002C| mW| 2| 1026| W| ●| ●| ●| ●| ●| ●
S1| Ph1 Apparent Power| ●| 3| 0028| 4| 0030| mVA| 2| 1028| VA| ●|  |  | ●|  | ●
S2| Ph2 Apparent Power| ●| 3| 002B| 4| 0034| mVA| 2| 102A| VA| ●|  |  | ●|  | ●
S3| Ph3 Apparent Power| ●| 3| 002E| 4| 0038| mVA| 2| 102C| VA| ●|  |  | ●|  | ●
S∑| Sys Apparent Power| ●| 3| 0031| 4| 003C| mVA| 2| 102E| VA| ●| ●| ●| ●| ●| ●
Q1| Ph1 Reactive Power| ●| 3| 0034| 4| 0040| mvar| 2| 1030| var| ●|  | | ●|  | ●
Q2| Ph2 Reactive Power| ●| 3| 0037| 4| 0044| mvar| 2| 1032| var| ●|  | | ●|  | ●
Q3| Ph3 Reactive Power| ●| 3| 003A| 4| 0048| mvar| 2| 1034| var| ●|  | | ●|  | ●
Q∑| Sys Reactive Power| ●| 3| 003D| 4| 004C| mvar| 2| 1036| var| ●| ●| ●| ●| ●| ●
F| Frequency|  | 1| 0040| 2| 0050| mHz| 2| 1038| Hz| ●| ●| ●| ●| ●| ●
PH SEQ| Phase Sequence|  | 1| 0041| 2| 0052| –| 2| 103A| –| ●|  |  | ●| | ●

Meaning of read data:

• INTEGER: $00=123-CCW, $01=321-CW, $02=not defined
• IEEE for Counters with Integrated Communication and RS485 Modules: $3DFBE76D=123-CCW, $3E072B02=321-CW, $0=not defined
• IEEE for LAN GATEWAY Modules: $0=123-CCW, $3F800000=321-CW, $40000000=not defined

+kWh1| Ph1 Imp. Active En.|  | 3| 0100| 4| 0100| 0.1Wh| 2| 1100| Wh| ●| |  | ●|  | ●
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
+kWh2| Ph2 Imp. Active En.|  | 3| 0103| 4| 0104| 0.1Wh| 2| 1102| Wh| ●| |  | ●|  | ●
+kWh3| Ph3 Imp. Active En.|  | 3| 0106| 4| 0108| 0.1Wh| 2| 1104| Wh| ●| |  | ●|  | ●
+kWh∑| Sys Imp. Active En.|  | 3| 0109| 4| 010C| 0.1Wh| 2| 1106| Wh| ●| ●| ●| ●| ●| ●
– kWh1| Ph1 Exp. Active En.|  | 3| 010C| 4| 0110| 0.1Wh| 2| 1108| Wh| ●|  |  | ●|  | ●
– kWh2| Ph2 Exp. Active En.|  | 3| 010F| 4| 0114| 0.1Wh| 2| 110A| Wh| ●|  |  | ●|  | ●
– kWh3| Ph3 Exp. Active En.|  | 3| 0112| 4| 0118| 0.1Wh| 2| 110C| Wh| ●|  |  | ●|  | ●
-kWh ∑| Sys Exp. Active En.|  | 3| 0115| 4| 011C| 0.1Wh| 2| 110E| Wh| ●| ●| ●| ●| ●| ●
+kVAh1- L| Ph1 Imp. Lag. Apparent En.|  | 3| 0118| 4| 0120| 0.1VAh| 2| 1110| VAh| ●|  |  | ●|  | ●
+kVAh2- L| Ph2 Imp. Lag. Apparent En.|  | 3| 011B| 4| 0124| 0.1VAh| 2| 1112| VAh| ●|  |  | ●|  | ●
+kVAh3- L| Ph3 Imp. Lag. Apparent En.|  | 3| 011E| 4| 0128| 0.1VAh| 2| 1114| VAh| ●|  |  | ●|  | ●
+kVAh∑- L| Sys Imp. Lag. Apparent En.|  | 3| 0121| 4| 012C| 0.1VAh| 2| 1116| VAh| ●| ●| ●| ●| ●| ●
-kVAh1-L| Ph1 Exp. Lag. Apparent En.|  | 3| 0124| 4| 0130| 0.1VAh| 2| 1118| VAh| ●|  |  | ●|  | ●
-kVAh2-L| Ph2 Exp. Lag. Apparent En.|  | 3| 0127| 4| 0134| 0.1VAh| 2| 111A| VAh| ●|  |  | ●|  | ●
-kVAh3-L| Ph3 Exp. Lag. Apparent En.|  | 3| 012A| 4| 0138| 0.1VAh| 2| 111C| VAh| ●|  |  | ●|  | ●
-kVAh∑-L| Sys Exp. Lag. Apparent En.|  | 3| 012D| 4| 013C| 0.1VAh| 2| 111E| VAh| ●| ●| ●| ●| ●| ●
+kVAh1- C| Ph1 Imp. Lead. Apparent En.|  | 3| 0130| 4| 0140| 0.1VAh| 2| 1120| VAh| ●|  |  | ●|  | ●
+kVAh2- C| Ph2 Imp. Lead. Apparent En.|  | 3| 0133| 4| 0144| 0.1VAh| 2| 1122| VAh| ●|  |  | ●|  | ●
+kVAh3- C| Ph3 Imp. Lead. Apparent En.|  | 3| 0136| 4| 0148| 0.1VAh| 2| 1124| VAh| ●|  |  | ●|  | ●
+kVAh∑- C| Sys Imp. Lead. Apparent En.|  | 3| 0139| 4| 014C| 0.1VAh| 2| 1126| VAh| ●| ●| ●| ●| ●| ●
-kVAh1-C| Ph1 Exp. Lead. Apparent En.|  | 3| 013C| 4| 0150| 0.1VAh| 2| 1128| VAh| ●|  |  | ●|  | ●
-kVAh2-C| Ph2 Exp. Lead. Apparent En.|  | 3| 013F| 4| 0154| 0.1VAh| 2| 112A| VAh| ●|  |  | ●|  | ●
-kVAh3-C| Ph3 Exp. Lead. Apparent En.|  | 3| 0142| 4| 0158| 0.1VAh| 2| 112C| VAh| ●|  |  | ●|  | ●
-VA∑-C| Sys Exp. Lead. Apparent En.|  | 3| 0145| 4| 015C| 0.1VAh| 2| 112E| VAh| ●| ●| ●| ●| ●| ●
+kvarh1- L| Ph1 Imp. Lag. Reactive En.|  | 3| 0148| 4| 0160| 0.1varh| 2| 1130| varh| ●|  |  | ●|  | ●
+kvarh2- L| Ph2 Imp. Lag. Reactive En.|  | 3| 014B| 4| 0164| 0.1varh| 2| 1132| varh| ●|  |  | ●|  | ●

+kvarh3- L| Ph3 Imp. Lag. Reactive En.|  | 3| 014E| 4| 0168| 0.1varh| 2| 1134| varh| ●|  |  | ●|  | ●
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
+kvarh∑- L| Sys Imp. Lag. Reactive En.|  | 3| 0151| 4| 016C| 0.1varh| 2| 1136| varh| ●| ●| ●| ●| ●| ●
-kvarh1-L| Ph1 Exp. Lag. Reactive En.|  | 3| 0154| 4| 0170| 0.1varh| 2| 1138| varh| ●|  |  | ●|  | ●
-kvarh2-L| Ph2 Exp. Lag. Reactive En.|  | 3| 0157| 4| 0174| 0.1varh| 2| 113A| varh| ●|  |  | ●|  | ●
-kvarh3-L| Ph3 Exp. Lag. Reactive En.|  | 3| 015A| 4| 0178| 0.1varh| 2| 113C| varh| ●|  |  | ●|  | ●
-vary∑-L| Sys Exp. Lag. Reactive En.|  | 3| 015D| 4| 017C| 0.1varh| 2| 113E| varh| ●| ●| ●| ●| ●| ●
+kvarh1- C| Ph1 Imp. Lead. Reactive En.|  | 3| 0160| 4| 0180| 0.1varh| 2| 1140| varh| ●|  |  | ●|  | ●
+kvarh2- C| Ph2 Imp. Lead. Reactive En.|  | 3| 0163| 4| 0184| 0.1varh| 2| 1142| varh| ●|  |  | ●|  | ●
+kvarh3- C| Ph3 Imp. Lead. Reactive En.|  | 3| 0166| 4| 0188| 0.1varh| 2| 1144| varh| ●|  |  | ●|  | ●
+kvarh∑- C| Sys Imp. Lead. Reactive En.|  | 3| 0169| 4| 018C| 0.1varh| 2| 1146| varh| ●| ●| ●| ●| ●| ●
-kvarh1-C| Ph1 Exp. Lead. Reactive En.|  | 3| 016C| 4| 0190| 0.1varh| 2| 1148| varh| ●|  |  | ●|  | ●
-kvarh2-C| Ph2 Exp. Lead. Reactive En.|  | 3| 016F| 4| 0194| 0.1varh| 2| 114A| varh| ●|  |  | ●|  | ●
-kvarh3-C| Ph3 Exp. Lead. Reactive En.|  | 3| 0172| 4| 0198| 0.1varh| 2| 114C| varh| ●|  |  | ●|  | ●
-kvarh∑-C| Sys Exp. Lead. Reactive En.|  | 3| 0175| 4| 019C| 0.1varh| 2| 114E| varh| ●| ●| ●| ●| ●| ●
– ** Reserved|  | 3| 0178| 2| 01A0| –| 2| 1150| –| R| R| R| R| R| R**

TARIFF 1 COUNTERS

+kWh1- T1| Ph1 Imp. Active En.|  | 3| 0200| 4| 0200| 0.1Wh| 2| 1200| Wh| ●|  |  |  |  | ●
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
+kWh2- T1| Ph2 Imp. Active En.|  | 3| 0203| 4| 0204| 0.1Wh| 2| 1202| Wh| ●|  |  |  |  | ●
+kWh3- T1| Ph3 Imp. Active En.|  | 3| 0206| 4| 0208| 0.1Wh| 2| 1204| Wh| ●|  |  |  |  | ●
+kWh∑- T1| Sys Imp. Active En.|  | 3| 0209| 4| 020C| 0.1Wh| 2| 1206| Wh| ●| ●|  |  |  | ●
-kWh1-T1| Ph1 Exp. Active En.|  | 3| 020C| 4| 0210| 0.1Wh| 2| 1208| Wh| ●|  |  |  |  | ●
-kWh2-T1| Ph2 Exp. Active En.|  | 3| 020F| 4| 0214| 0.1Wh| 2| 120A| Wh| ●|  |  |  |  | ●
-kWh3-T1| Ph3 Exp. Active En.|  | 3| 0212| 4| 0218| 0.1Wh| 2| 120C| Wh| ●|  |  |  |  | ●
-kWh∑-T1| Sys Exp. Active En.|  | 3| 0215| 4| 021C| 0.1Wh| 2| 120E| Wh| ●| ●|  |  |  | ●
+kVAh1-L-T1| Ph1 Imp. Lag. Apparent En.|  | 3| 0218| 4| 0220| 0.1VAh| 2| 1210| VAh| ●|  |  |  |  | ●
+kVAh2-L-T1| Ph2 Imp. Lag. Apparent En.|  | 3| 021B| 4| 0224| 0.1VAh| 2| 1212| VAh| ●|  |  |  |  | ●
+kVAh3-L-T1| Ph3 Imp. Lag. Apparent En.|  | 3| 021E| 4| 0228| 0.1VAh| 2| 1214| VAh| ●|  |  |  |  | ●
+kVAh∑-L-T1| Sys Imp. Lag. Apparent En.|  | 3| 0221| 4| 022C| 0.1VAh| 2| 1216| VAh| ●| ●|  |  |  | ●
-kVAh1-L-T1| Ph1 Exp. Lag. Apparent En.|  | 3| 0224| 4| 0230| 0.1VAh| 2| 1218| VAh| ●|  |  |  |  | ●
-kVAh2-L-T1| Ph2 Exp. Lag. Apparent En.|  | 3| 0227| 4| 0234| 0.1VAh| 2| 121A| VAh| ●|  |  |  |  | ●
-kVAh3-L-T1| Ph3 Exp. Lag. Apparent En.|  | 3| 022A| 4| 0238| 0.1VAh| 2| 121C| VAh| ●|  |  |  |  | ●
-kVAh∑-L-T1| Sys Exp. Lag. Apparent En.|  | 3| 022D| 4| 023C| 0.1VAh| 2| 121E| VAh| ●| ●|  |  |  | ●
+kVAh1-C-T1| Ph1 Imp. Lead. Apparent En.|  | 3| 0230| 4| 0240| 0.1VAh| 2| 1220| VAh| ●|  |  |  |  | ●
+kVAh2-C-T1| Ph2 Imp. Lead. Apparent En.|  | 3| 0233| 4| 0244| 0.1VAh| 2| 1222| VAh| ●|  |  |  |  | ●
+kVAh3-C-T1| Ph3 Imp. Lead. Apparent En.|  | 3| 0236| 4| 0248| 0.1VAh| 2| 1224| VAh| ●|  |  |  |  | ●
+kVAh∑-C-T1| Sys Imp. Lead. Apparent En.|  | 3| 0239| 4| 024C| 0.1VAh| 2| 1226| VAh| ●| ●|  |  |  | ●
-kVAh1-C-T1| Ph1 Exp. Lead. Apparent En.|  | 3| 023C| 4| 0250| 0.1VAh| 2| 1228| VAh| ●|  |  |  |  | ●
-kVAh2-C-T1| Ph2 Exp. Lead. Apparent En.|  | 3| 023F| 4| 0254| 0.1VAh| 2| 122A| VAh| ●|  |  |  |  | ●
-kVAh3-C-T1| Ph3 Exp. Lead. Apparent En.|  | 3| 0242| 4| 0258| 0.1VAh| 2| 122C| VAh| ●|  |  |  |  | ●
-kVAh∑-C-T1| Sys Exp. Lead. Apparent En.|  | 3| 0245| 4| 025C| 0.1VAh| 2| 122E| VAh| ●| ●|  |  |  | ●
+kvarh1-L-T1| Ph1 Imp. Lag. Reactive En.|  | 3| 0248| 4| 0260| 0.1varh| 2| 1230| varh| ●|  |  |  |  | ●
+kvarh2-L-T1| Ph2 Imp. Lag. Reactive En.|  | 3| 024B| 4| 0264| 0.1varh| 2| 1232| varh| ●|  |  |  |  | ●
+kvarh3-L-T1| Ph3 Imp. Lag. Reactive En.|  | 3| 024E| 4| 0268| 0.1varh| 2| 1234| varh| ●|  |  |  |  | ●
+kvarh∑-L-T1| Sys Imp. Lag. Reactive En.|  | 3| 0251| 4| 026C| 0.1varh| 2| 1236| varh| ●| ●|  |  |  | ●
-kvarh1-L-T1| Ph1 Exp. Lag. Reactive En.|  | 3| 0254| 4| 0270| 0.1varh| 2| 1238| varh| ●|  |  |  |  | ●
-kvarh2-L-T1| Ph2 Exp. Lag. Reactive En.|  | 3| 0257| 4| 0274| 0.1varh| 2| 123A| varh| ●|  |  |  |  | ●
-kvarh3-L-T1| Ph3 Exp. Lag. Reactive En.|  | 3| 025A| 4| 0278| 0.1varh| 2| 123C| varh| ●|  |  |  |  | ●
-vary∑-L-T1| Sys Exp. Lag. Reactive En.|  | 3| 025D| 4| 027C| 0.1varh| 2| 123E| varh| ●| ●|  |  |  | ●
+kvarh1-C-T1| Ph1 Imp. Lead. Reactive En.|  | 3| 0260| 4| 0280| 0.1varh| 2| 1240| varh| ●|  |  |  |  | ●
+kvarh2-C-T1| Ph2 Imp. Lead. Reactive En.|  | 3| 0263| 4| 0284| 0.1varh| 2| 1242| varh| ●|  |  |  |  | ●
+kvarh3-C-T1| Ph3 Imp. Lead. Reactive En.|  | 3| 0266| 4| 0288| 0.1varh| 2| 1244| varh| ●|  |  |  |  | ●
+kvarh∑-C-T1| Sys Imp. Lead. Reactive En.|  | 3| 0269| 4| 028C| 0.1varh| 2| 1246| varh| ●| ●|  |  |  | ●
-kvarh1-C-T1| Ph1 Exp. Lead. Reactive En.|  | 3| 026C| 4| 0290| 0.1varh| 2| 1248| varh| ●|  |  |  |  | ●
-kvarh2-C-T1| Ph2 Exp. Lead. Reactive En.|  | 3| 026F| 4| 0294| 0.1varh| 2| 124A| varh| ●|  |  |  |  | ●
-kvarh3-C-T1| Ph3 Exp. Lead. Reactive En.|  | 3| 0272| 4| 0298| 0.1varh| 2| 124C| varh| ●|  |  |  |  | ●
-kvarh∑-C-T1| Sys Exp. Lead. Reactive En.|  | 3| 0275| 4| 029C| 0.1varh| 2| 124E| varh| ●| ●|  |  |  | ●
– ** Reserved|  | 3| 0278| –| –| –| –| –| –| R| R| R| R| R| R**

+kWh1- T2| Ph1 Imp. Active En.|  | 3| 0300| 4| 0300| 0.1Wh| 2| 1300| Wh| ●|  |  |  |  | ●
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
+kWh2- T2| Ph2 Imp. Active En.|  | 3| 0303| 4| 0304| 0.1Wh| 2| 1302| Wh| ●|  |  |  |  | ●
+kWh3- T2| Ph3 Imp. Active En.|  | 3| 0306| 4| 0308| 0.1Wh| 2| 1304| Wh| ●|  |  |  |  | ●
+kWh∑- T2| Sys Imp. Active En.|  | 3| 0309| 4| 030C| 0.1Wh| 2| 1306| Wh| ●| ●|  |  |  | ●
-kWh1-T2| Ph1 Exp. Active En.|  | 3| 030C| 4| 0310| 0.1Wh| 2| 1308| Wh| ●|  |  |  |  | ●
-kWh2-T2| Ph2 Exp. Active En.|  | 3| 030F| 4| 0314| 0.1Wh| 2| 130A| Wh| ●|  |  |  |  | ●
-kWh3-T2| Ph3 Exp. Active En.|  | 3| 0312| 4| 0318| 0.1Wh| 2| 130C| Wh| ●|  |  |  |  | ●
-kWh∑-T2| Sys Exp. Active En.|  | 3| 0315| 4| 031C| 0.1Wh| 2| 130E| Wh| ●| ●|  |  |  | ●
+kVAh1-L-T2| Ph1 Imp. Lag. Apparent En.|  | 3| 0318| 4| 0320| 0.1VAh| 2| 1310| VAh| ●|  |  |  |  | ●
+kVAh2-L-T2| Ph2 Imp. Lag. Apparent En.|  | 3| 031B| 4| 0324| 0.1VAh| 2| 1312| VAh| ●|  |  |  |  | ●
+kVAh3-L-T2| Ph3 Imp. Lag. Apparent En.|  | 3| 031E| 4| 0328| 0.1VAh| 2| 1314| VAh| ●|  |  |  |  | ●
+kVAh∑-L-T2| Sys Imp. Lag. Apparent En.|  | 3| 0321| 4| 032C| 0.1VAh| 2| 1316| VAh| ●| ●|  |  |  | ●
-kVAh1-L-T2| Ph1 Exp. Lag. Apparent En.|  | 3| 0324| 4| 0330| 0.1VAh| 2| 1318| VAh| ●|  |  |  |  | ●
-kVAh2-L-T2| Ph2 Exp. Lag. Apparent En.|  | 3| 0327| 4| 0334| 0.1VAh| 2| 131A| VAh| ●|  |  |  |  | ●
-kVAh3-L-T2| Ph3 Exp. Lag. Apparent En.|  | 3| 032A| 4| 0338| 0.1VAh| 2| 131C| VAh| ●|  |  |  |  | ●
-kVAh∑-L-T2| Sys Exp. Lag. Apparent En.|  | 3| 032D| 4| 033C| 0.1VAh| 2| 131E| VAh| ●| ●|  |  |  | ●
+kVAh1-C-T2| Ph1 Imp. Lead. Apparent En.|  | 3| 0330| 4| 0340| 0.1VAh| 2| 1320| VAh| ●|  |  |  |  | ●
+kVAh2-C-T2| Ph2 Imp. Lead. Apparent En.|  | 3| 0333| 4| 0344| 0.1VAh| 2| 1322| VAh| ●|  |  |  |  | ●
+kVAh3-C-T2| Ph3 Imp. Lead. Apparent En.|  | 3| 0336| 4| 0348| 0.1VAh| 2| 1324| VAh| ●|  |  |  |  | ●
+kVAh∑-C-T2| Sys Imp. Lead. Apparent En.|  | 3| 0339| 4| 034C| 0.1VAh| 2| 1326| VAh| ●| ●|  |  |  | ●
-kVAh1-C-T2| Ph1 Exp. Lead. Apparent En.|  | 3| 033C| 4| 0350| 0.1VAh| 2| 1328| VAh| ●|  |  |  |  | ●
-kVAh2-C-T2| Ph2 Exp. Lead. Apparent En.|  | 3| 033F| 4| 0354| 0.1VAh| 2| 132A| VAh| ●|  |  |  |  | ●
-kVAh3-C-T2| Ph3 Exp. Lead. Apparent En.|  | 3| 0342| 4| 0358| 0.1VAh| 2| 132C| VAh| ●|  |  |  |  | ●
-kVAh∑-C-T2| Sys Exp. Lead. Apparent En.|  | 3| 0345| 4| 035C| 0.1VAh| 2| 132E| VAh| ●| ●|  |  |  | ●
+kvarh1-L-T2| Ph1 Imp. Lag. Reactive En.|  | 3| 0348| 4| 0360| 0.1varh| 2| 1330| varh| ●|  |  |  |  | ●
+kvarh2-L-T2| Ph2 Imp. Lag. Reactive En.|  | 3| 034B| 4| 0364| 0.1varh| 2| 1332| varh| ●|  |  |  |  | ●
+kvarh3-L-T2| Ph3 Imp. Lag. Reactive En.|  | 3| 034E| 4| 0368| 0.1varh| 2| 1334| varh| ●|  |  |  |  | ●
+kvarh∑-L-T2| Sys Imp. Lag. Reactive En.|  | 3| 0351| 4| 036C| 0.1varh| 2| 1336| varh| ●| ●|  |  |  | ●
-kvarh1-L-T2| Ph1 Exp. Lag. Reactive En.|  | 3| 0354| 4| 0370| 0.1varh| 2| 1338| varh| ●|  |  |  |  | ●
-kvarh2-L-T2| Ph2 Exp. Lag. Reactive En.|  | 3| 0357| 4| 0374| 0.1varh| 2| 133A| varh| ●|  |  |  |  | ●
-kvarh3-L-T2| Ph3 Exp. Lag. Reactive En.|  | 3| 035A| 4| 0378| 0.1varh| 2| 133C| varh| ●|  |  |  |  | ●
-vary∑-L-T2| Sys Exp. Lag. Reactive En.|  | 3| 035D| 4| 037C| 0.1varh| 2| 133E| varh| ●| ●|  |  |  | ●
+kvarh1-C-T2| Ph1 Imp. Lead. Reactive En.|  | 3| 0360| 4| 0380| 0.1varh| 2| 1340| varh| ●|  |  |  |  | ●
+kvarh2-C-T2| Ph2 Imp. Lead. Reactive En.|  | 3| 0363| 4| 0384| 0.1varh| 2| 1342| varh| ●|  |  |  |  | ●
+kvarh3-C-T2| Ph3 Imp. Lead. Reactive En.|  | 3| 0366| 4| 0388| 0.1varh| 2| 1344| varh| ●|  |  |  |  | ●
+kvarh∑-C-T2| Sys Imp. Lead. Reactive En.|  | 3| 0369| 4| 038C| 0.1varh| 2| 1346| varh| ●| ●|  |  |  | ●
-kvarh1-C-T2| Ph1 Exp. Lead. Reactive En.|  | 3| 036C| 4| 0390| 0.1varh| 2| 1348| varh| ●|  |  |  |  | ●
-kvarh2-C-T2| Ph2 Exp. Lead. Reactive En.|  | 3| 036F| 4| 0394| 0.1varh| 2| 134A| varh| ●|  |  |  |  | ●
-kvarh3-C-T2| Ph3 Exp. Lead. Reactive En.|  | 3| 0372| 4| 0398| 0.1varh| 2| 134C| varh| ●|  |  |  |  | ●
-vary∑-C-T2| Sys Exp. Lead. Reactive En.|  | 3| 0375| 4| 039C| 0.1varh| 2| 134E| varh| ●| ●|  |  |  | ●
– ** Reserved|  | 3| 0378| –| –| –| –| –| –| R| R| R| R| R| R**

PARTIAL COUNTERS

+kWh∑- P| Sys Imp. Active En.|  | 3| 0400| 4| 0400| 0.1Wh| 2| 1400| Wh| ●| ●| ●| ●| ●| ●
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
-kWh∑-P| Sys Exp. Active En.|  | 3| 0403| 4| 0404| 0.1Wh| 2| 1402| Wh| ●| ●| ●| ●| ●| ●
+kVAh∑-L-P| Sys Imp. Lag. Apparent En.|  | 3| 0406| 4| 0408| 0.1VAh| 2| 1404| VAh| ●| ●| ●| ●| ●| ●
-kVAh∑-L-P| Sys Exp. Lag. Apparent En.|  | 3| 0409| 4| 040C| 0.1VAh| 2| 1406| VAh| ●| ●| ●| ●| ●| ●
+kVAh∑-C-P| Sys Imp. Lead. Apparent En.|  | 3| 040C| 4| 0410| 0.1VAh| 2| 1408| VAh| ●| ●| ●| ●| ●| ●
-kVAh∑-C-P| Sys Exp. Lead. Apparent En.|  | 3| 040F| 4| 0414| 0.1VAh| 2| 140A| VAh| ●| ●| ●| ●| ●| ●
+kvarh∑-L-P| Sys Imp. Lag. Reactive En.|  | 3| 0412| 4| 0418| 0.1varh| 2| 140C| varh| ●| ●| ●| ●| ●| ●
-vary∑-L-P| Sys Exp. Lag. Reactive En.|  | 3| 0415| 4| 041C| 0.1varh| 2| 140E| varh| ●| ●| ●| ●| ●| ●
+kvarh∑-C-P| Sys Imp. Lead. Reactive En.|  | 3| 0418| 4| 0420| 0.1varh| 2| 1410| varh| ●| ●| ●| ●| ●| ●
-vary∑-C-P| Sys Exp. Lead. Reactive En.|  | 3| 041B| 4| 0424| 0.1varh| 2| 1412| varh| ●| ●| ●| ●| ●| ●

BALANCE COUNTERS

kWh∑- B| Sys Active En.| ●| 3| 041E| 4| 0428| 0.1Wh| 2| 1414| Wh| ●| ●|  | ●| ●| ●
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
kVAh∑-L-B| Sys Lag. Apparent En.| ●| 3| 0421| 4| 042C| 0.1VAh| 2| 1416| VAh| ●| ●|  | ●| ●| ●
kVAh∑-C-B| Sys Lead. Apparent En.| ●| 3| 0424| 4| 0430| 0.1VAh| 2| 1418| VAh| ●| ●|  | ●| ●| ●
kvarh∑-L-B| Sys Lag. Reactive En.| ●| 3| 0427| 4| 0434| 0.1varh| 2| 141A| varh| ●| ●|  | ●| ●| ●
kvarh∑-C-B| Sys Lead. Reactive En.| ●| 3| 042A| 4| 0438| 0.1varh| 2| 141C| varh| ●| ●|  | ●| ●| ●
– ** Reserved|  | 3| 042D| –| –| –| –| –| –| R| R| R| R| R| R**

EC SN| Counter Serial Number| 5| 0500| 6| 0500| 10 ASCII chars. ($00…$FF)| ●| ●| ●| ●| ●| ●
---|---|---|---|---|---|---|---|---|---|---|---|---
EC MODEL| Counter Model| 1| 0505| 2| 0506| $03=6A 3phases, 4wires

$08=80A 3phases, 4wires

$0C=80A 1phase, 2wires

$10=40A 1phase, 2wires

$12=63A 3phases, 4wires

| ●| ●| ●| ●| ●| ●
EC TYPE| Counter Type| 1| 0506| 2| 0508| $00=NO MID, RESET

$01=NO MID

$02=MID

$03=NO MID, Wiring selection

$05=MID no vary

$09=MID, Wiring selection

$0A=MID no vary, Wiring selection

$0B=NO MID, RESET, Wiring selection

| ●| ●| ●| ●| ●| ●
EC FW REL1| Counter Firmware Release 1| 1| 0507| 2| 050A| Convert the read Hex value to the Dec value.

e.g. $66=102 => rel. 1.02

| ●| ●| ●| ●| ●| ●
EC HW VER| Counter Hardware Version| 1| 0508| 2| 050C| Convert the read Hex value to the Dec value.

e.g. $64=100 => ver. 1.00

| ●| ●| ●| ●| ●| ●
–| Reserved| 2| 0509| 2| 050E| –| R| R| R| R| R| R
T| Tariff in use| 1| 050B| 2| 0510| $01=tariff 1

$02=tariff 2

| ●| ●|  |  |  | ●
PRI/SEC| Primary/Secondary Value Only 6A model. Reserved and

fixed to 0 for other models.

| 1| 050C| 2| 0512| $00=primary

$01=secondary

| ●|  |  | ●|  | ●
ERR| Error Code| 1| 050D| 2| 0514| Bit field coding:

– bit0 (LSb)=Phase sequence

– bit1=Memory

– bit2=Clock (RTC)-Only ETH model

– other bits not used

Bit=1 means error condition, Bit=0 means no error

| ●| ●| ●| ●| ●| ●
CT| CT Ratio Value

Only 6A model. Reserved and

fixed to 1 for other models.

| 1| 050E| 2| 0516| $0001…$2710| ●|  |  | ●|  | ●
–| Reserved| 2| 050F| 2| 0518| –| R| R| R| R| R| R
FSA| FSA Value| 1| 0511| 2| 051A| $00=1A

$01=5A

$02=80A

$03=40A

$06=63A

| ●| ●| ●| ●| ●| ●
WIR| Wiring Mode| 1| 0512| 2| 051C| $01=3phases, 4 wires, 3 currents

$02=3phases, 3 wires, 2 currents

$03=1phase

$04=3phases, 3 wires, 3 currents

| ●| ●| ●| ●| ●| ●
ADDR| MODBUS Address| 1| 0513| 2| 051E| $01…$F7| ●| ●| ●| ●| ●| ●
MDB MODE| MODBUS Mode| 1| 0514| 2| 0520| $00=7E2 (ASCII)

$01=8N1 (RTU)

| ●| ●| ●|  |  |
BAUD| Communication Speed| 1| 0515| 2| 0522| $01=300 bps

$02=600 bps

$03=1200 bps

$04=2400 bps

$05=4800 bps

$06=9600 bps

$07=19200 bps

$08=38400 bps

$09=57600 bps

| ●| ●| ●|  |  |
–| Reserved| 1| 0516| 2| 0524| –| R| R| R| R| R| R

INFORMATION ON ENERGY COUNTER AND COMMUNICATION MODULE

EC-P STAT| Partial Counter Status| 1| 0517| 2| 0526| Bit field coding:

– bit0 (LSb)= +kWhΣ PAR

– bit1=-kWhΣ PAR

– bit2=+kVAhΣ-L PAR

– bit3=-kVAhΣ-L PAR

– bit4=+kVAhΣ-C PAR

– bit5=-kVAhΣ-C PAR

– bit6=+kvarhΣ-L PAR

– bit7=-kvarhΣ-L PAR

– bit8=+kvarhΣ-C PAR

– bit9=-kvarhΣ-C PAR

– other bits not used

Bit=1 means counter active, Bit=0 means counter stopped

| ●| ●| ●| ●| ●| ●
---|---|---|---|---|---|---|---|---|---|---|---|---
PARAMETER| INTEGER| DATA MEANING| REGISTER AVAILABILITY BY MODEL
---|---|---|---

Symbol

| ****

Description

| RegSet 0| RegSet 1| ****

Values

| 3ph 6A/63A/80A SERIAL| 1ph 80A SERIAL| 1ph 40A SERIAL| 3ph Integrated ETHERNET TCP| 1ph Integrated ETHERNET TCP| LANG TCP

(according to the model)

MOD SN| Module Serial Number| 5| 0518| 6| 0528| 10 ASCII chars. ($00…$FF)| ●| ●|  |  |  | ●
SIGN| Signed Value Representation| 1| 051D| 2| 052E| $00=sign bit

$01=2’s complement

| ●| ●| ●| ●| ●|
– ** Reserved| 1| 051E| 2| 0530| –| R| R| R| R| R| R
MOD FW REL**| Module Firmware Release| 1| 051F| 2| 0532| Convert the read Hex value to the Dec value.

e.g. $66=102 => rel. 1.02

| ●| ●|  |  |  | ●
MOD HW VER| Module Hardware Version| 1| 0520| 2| 0534| Convert the read Hex value to the Dec value.

e.g. $64=100 => ver. 1.00

| ●| ●|  |  |  | ●
– ** Reserved| 2| 0521| 2| 0536| –| R| R| R| R| R| R
REGSET**| RegSet in use| 1| 0523| 2| 0538| $00=register set 0

$01=register set 1

| ●| ●|  | ●| ●|
2| 0538| 2| 0538| $00=register set 0

$01=register set 1

|  |  | ●|  |  |
FW REL2| Counter Firmware Release 2| 1| 0600| 2| 0600| Convert the read Hex value to the Dec value.

e.g. $C8=200 => rel. 2.00

| ●| ●| ●| ●| ●| ●
RTC- DAY| Ethernet interface RTC day| 1| 2000| 1| 2000| Convert the read Hex value to the Dec value.

e.g. $1F=31 => day 31

|  |  |  | ●| ●|
RTC- MONTH| Ethernet interface RTC month| 1| 2001| 1| 2001| Convert the read Hex value to the Dec value.

e.g. $0C=12 => December

|  |  |  | ●| ●|
RTC- YEAR| Ethernet interface RTC year| 1| 2002| 1| 2002| Convert the read Hex value to the Dec value.

e.g. $15=21 => year 2021

|  |  |  | ●| ●|
RTC- HOURS| Ethernet interface RTC hours| 1| 2003| 1| 2003| Convert the read Hex value to the Dec value.

e.g. $0F=15 => 15 hours

|  |  |  | ●| ●|
RTC- MIN| Ethernet interface RTC minutes| 1| 2004| 1| 2004| Convert the read Hex value to the Dec value.

e.g. $1E=30 => 30 minutes

|  |  |  | ●| ●|
RTC-SEC| Ethernet interface RTC seconds| 1| 2005| 1| 2005| Convert the read Hex value to the Dec value.

e.g. $0A=10 => 10 seconds

|  |  |  | ●| ●|

NOTE: the RTC registers ($2000…$2005) are available only for energy meters with Ethernet Firmware rel. 1.15 or higher.

COILS READING (FUNCTION CODE $01)

PARAMETER| INTEGER| DATA MEANING| REGISTER AVAILABILITY BY MODEL
---|---|---|---

Symbol Description

| Bits

Address

| ****

Values

| 3ph 6A/63A/80A SERIAL| 1ph 80A SERIAL| 1ph 40A SERIAL| 3ph Integrated ETHERNET TCP| 1ph Integrated ETHERNET TCP| LANG TCP

(according to the model)

AL ** Alarms| 40         0000| Bit sequence bit 39 (MSB) … bit 0 (LSb):**

|U3N-L|U2N-L|U1N-L|UΣ-L|U3N-H|U2N-H|U1N-H|UΣ-H|

|COM|RES|U31-L|U23-L|U12-L|U31-H|U23-H|U12-H|

|RES|RES|RES|RES|RES|RES|AN-L|A3-L|

|A2-L|A1-L|AΣ-L|AN-H|A3-H|A2-H|A1-H|AΣ-H|

|RES|RES|RES|RES|RES|RES|RES|f-O|

LEGEND

L=Under the Threshold (Low) H=Over the Threshold (High) O=Out of Range

COM=Communication on IR port OK. Do not consider in case of models with integrated SERIAL communication

RES=Bit Reserved to 0

NOTE: Voltage, Current and Frequency Threshold Values can change according to the counter model. Please refer to the

tables are shown below.

| ●| ●|  | ●| ●| ●
VOLTAGE AND FREQUENCY RANGES ACCORDING TO MODEL| PARAMETER THRESHOLDS
---|---
PHASE-NEUTRAL VOLTAGE| PHASE-PHASE VOLTAGE| CURRENT| FREQUENCY
 |  |  |  |
3×230/400V 50Hz| ULN-L=230V-20%=184V

ULN-H=230V+20%=276V

| ULL-L=230V x √3 -20%=318V

ULL-H=230V x √3 +20%=478V

| ****

I-L=Starting Current (Ist)

I-H=Current Full Scale (IFS)

| ****

f-L=45Hz f-H=65Hz

3×230/400…3×240/415V 50/60Hz| ULN-L=230V-20%=184V

ULN-H=240V+20%=288V

| ULL-L=398V-20%=318V

ULL-H=415V+20%=498V

WRITING REGISTERS (FUNCTION CODE $10)

PROGRAMMABLE DATA FOR ENERGY COUNTER AND COMMUNICATION MODULE

$01=8N1 (RTU)

| ●| ●|  |  |  |
BAUD| Communication Speed

*300, 600, 1200, 57600 values

not available for the 40A model.

| 1| 0515| 2| 0522| $01=300 bps*

$02=600 bps*

$03=1200 bps*

$04=2400 bps

$05=4800 bps

$06=9600 bps

$07=19200 bps

$08=38400 bps

$09=57600 bps*

| ●| ●| ●|  |  |
EC RES| Reset Energy Counters

Only type with the RESET function

| 1| 0516| 2| 0524| $00=TOTAL Counters

$03=ALL Counters

| ●| ●| ●| ●| ●| ●
 |  |  |  |  |  | $01=TARIFF 1 Counters

$02=TARIFF 2 Counters

| ●| ●|  |  |  | ●
EC-P OPER| Partial Counter Operation| 1| 0517| 2| 0526| For RegSet1, set the MS word always to 0000. The LS word must be structured as follows:

Byte 1 – PARTIAL Counter Selection

$00=+kWhΣ PAR

$01=-kWhΣ PAR

$02=+kVAhΣ-L PAR

$03=-kVAhΣ-L PAR

$04=+kVAhΣ-C PAR

$05=-kVAhΣ-C PAR

$06=+kvarhΣ-L PAR

$07=-kvarhΣ-L PAR

$08=+kvarhΣ-C PAR

$09=-kvarhΣ-C PAR

$0A=ALL Partial Counters

Byte 2 – PARTIAL Counter Operation

$01=start

$02=stop

$03=reset

e.g. Start +kWhΣ PAR Counter

00=+kWhΣ PAR

01=start

Final value to be set:

– RegSet0=0001

– RegSet1=00000001

| ●| ●| ●| ●| ●| ●
REGSET| RegSet switching| 1| 100B| 2| 1010| $00=switch to RegSet 0

$01=switch to RegSet 1

| ●| ●|  | ●| ●|
 |  | 2| 0538| 2| 0538| $00=switch to RegSet 0

$01=switch to RegSet 1

|  |  | ●|  |  |
RTC- DAY| Ethernet interface RTC day| 1| 2000| 1| 2000| $01…$1F (1…31)|  |  |  | ●| ●|
RTC- MONTH| Ethernet interface RTC month| 1| 2001| 1| 2001| $01…$0C (1…12)|  |  |  | ●| ●|
RTC- YEAR| Ethernet interface RTC year| 1| 2002| 1| 2002| $01…$25 (1…37=2001…2037)

e.g. to set 2021, write $15

|  |  |  | ●| ●|
RTC- HOURS| Ethernet interface RTC hours| 1| 2003| 1| 2003| $00…$17 (0…23)|  |  |  | ●| ●|
RTC- MIN| Ethernet interface RTC minutes| 1| 2004| 1| 2004| $00…$3B (0…59)|  |  |  | ●| ●|
RTC-SEC| Ethernet interface RTC seconds| 1| 2005| 1| 2005| $00…$3B (0…59)|  |  |  | ●| ●|

NOTE: the RTC registers ($2000…$2005) are available only for energy meters with Ethernet Firmware rel. 1.15 or higher.
NOTE: if the RTC writing command contains inappropriate values (e.g. 30th February), the value will not be accepted and the device replies with an exception code (Illegal Value).
NOTE: in case of RTC loss due to a long time power off, set again the RTC value (day, month, year, hours, min, sec) to restart the recordings.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>