iMin M2-203 Mobile Terminal User Manual
- June 12, 2024
- imin
Table of Contents
M2-203
Mobile POS User Manual
Mobile POS Introduction
Power Button
Press the power button to power on.
Under power on conditions, press and hold the button for 2-3 seconds to select
power off or reboot.
In the standby status, press the control button for 8 sec. to power off.
Display
Atouch screen for the operator.
Camera
To scan the QR code and shoot.
Type-C Port
With the charging function, for external devices, such as U disk.
Pogo Pin
Used to connect the charging base for charging (optional).
Installation Guide
- O0pen the battery cover;
- Insert the MicroSD Card, Micro Sim Card, PSAM Card (optional) as required;
- Unscrew the printer cover and the paper compartment door pops open;
- insert the thermal paper and pull out part of it outside the paper exit of the printer, then close the paper compartment cover.
Charging Base Instructions (Optional)
- Use a data cable to insert a Type-A Port (OTG device) or a Type-C Port (for charging only, then press the wire into the Wire Slot;
- Put the host on the charging base correctly, after the successfully connected, tur on the power to start charging.
Mobile POS Technical Specifications
OS | Android 8.1 |
---|---|
CPU | MT8765 |
Screen | 5.5 inches, resolution: 720 x 1280 |
Storage | 1GB RAM (optional 2GB) + 8GB ROM (optional 16GB) |
Touch Screen | 5 multi-touch capacitive screen |
Camera | 5.0M AF |
WIFI | Support 802.11a/b/g/n (2.4G&5G) |
GSM | Band 2/3/5/8 |
3G | Band 1/2/5/8 |
4G LTE | LTE band/3/4/5/7/8/17/20/38/39/40/41M |
Bluetooth | 4.2BLE |
GPS | GPS + Gleans/Beidou |
Printer | 58mm thermal printer, maximum support the paper with 40mm diameter |
Speaker | 1.2W |
External Interface | 1 x USB Type-C port (OTG support), 1 x Earphone jack |
TF Card | Support MicroSD (TF) up to 128GB |
PSAM Card (optional) | Contactable with read and write mode, support IOS7816 |
standard
Micro Sim Card| 12mm x 15mm x 0.8mm
Battery| Changeable, 7.4V/2600mAh
Power Adapter| 5V/2A
Machine Size| 206mm x 82mm x 62.8mm
Operating Temperature| -10°C to +40°C
Storage Temperature| -10°C to +50°C
Limit Altitude| Under 5000 meters
Extended Support| Charge Pedestal (optional)
Name And Content Of Toxic And Harmful Substances In This Product
Part name | Tosic or harmful substances and elements |
---|---|
Plumbed (Pb) | Mercury (Hg) |
Polybrominated biphenyl (Cr(VI I)) | Polybrominated diphenyl ethers (PBDE) |
Circuit board | X |
Head of printer | X |
O: Means that the content of the toxic and harmful substances in all
homogeneous materials of the component is below the it specified in SJ/
t113363-2006.
X: Means that the content of the toxic and hazardous substances at least in a
homogenous material of the component exceeds the limit specified in 51/
£113363-2006. However, the components marked with “X “in the above table are
out of proportion because there is no mature alternative technology in the
industry at present.
Products that have reached or exceeded the environmental protection service
life should be recycled and reused in accordance with the electronic
information products control and management measures or local environmental
laws and guidelines. They should not be discarded at will or with household
waste.
Safety Information
Safety And Handiing
- Please plug-in power adapter to only its corresponding AC socket. Do not use in explosive gas atmosphere.
- Do not disassemble the equipment. It should be serviced or recycled only by iMin or an authorised service provider.
- This s a Grade B product. The product may cause radio interference and interfere with medical devices. The user may be required to take practical measures to reduce the possibility of causing interference to radios, televisions and other electronic devices.
Company Statement
Our company is not responsible for the following actions:
- Damage caused by misuse, lack of care in maintaining the equipment, or placing the device under conditions that may cause undesired operation and risk as specifying this instruction manual
- We will not be responsible for any damage or problem caused by third party parts or components (other than the original products or approved products provided by us). Without our consent, you have no right to modify or alter the products.
- The operating system o this product is supported by official regular OS update. If the user breached the third party’s ROM system or change the system file by hacking, it may cause unstable, undesired system operation and bring security risk.
Advices
- Do not expose the device to moisture, dampness, or wet weather, such as rain, Snow or fog.
- Do not use the device in extreme cold or hot environments eg, near a fire or it cigarette.
- Do not topple, throw, or bend.
- Use in optimally clean and dust-free environment to avoid tiny particles clogging and seeping through gaps in the device.
- Do not attempt to use the device near medical equipment.
Important Safety Information
Do not install or use during thunder storms and lightning conditions,
otherwise, there will be risk of electric shock, injury or death in the event
of thunder or lightning hit.
- If you find unusual odour, overheating or smoke, please cu off the power immediately.
- Do not expose the device to moisture, dampness, o wet weather, such as rain, snow or fog; Do not use in explosive gas atmosphere.
- The RF distance between the product and body is Smm.
Disclaimer
Due to regular updates and enhancements made to the product, some details of
this document may be inconsistent with the physical product. Please take the
product You received as current standard. The right to interpret this document
belongs to our company. We reserve the right to amend this specification
without prior notice.
Product Warranty Card
Product Name: Mobile POS
Model No.:…………………………………
Serial No…………………………………….
Purchase Date:………………………………
Warranty Period: The warranty period commences on the date of purchase.
We offer 365 days warranty service.
User Phone:…………………………………….
User Address:…………………………………
iMin does not warrant against the following:
- Disassembled or repaired product by unauthorised service provider without our consent.
- Damaged product barcode, fragile sticker and altered or defective warranty card.
- Damage caused by non-compliance with instructions in this user manual,
- Damage caused by exposure to sources of equid, dripping or splashing, normal wear and tear, accident or abuse.
- Failure or damage as a result of any Force Majeure Event,
- Expired warranty period.
Packing Content
- Mobile POS x 1
- Power Adapter x 1
- EUSB Cable x 1
- Printing Paper x 1
- User Manual x 1
https://www.imin.sg/
Qualification Corticate
Passed Inspection
Designed by iMin in Singapore
TEL: +65 67413019
FAX: +65 67413989
URL: wwww.imin.sg
Address: 11 Bishan Street 21 #03-05 Singapore 573943