EcoNet Controls SmartLife Smart App User Guide

June 12, 2024
Econet Controls

EcoNet Controls SmartLife Smart App

Note:

  • Your device must be on a Wifi network that utilizes the 2.4 GHz band. This band has much better range than the 5GHz band which is why it is used. Dual Band SSIDs will work.
  • WiFi WPA3 security is not supported, please use WPA2. Use a guest network if required.

Smart Life Install and Configuration

Screenshots are from an Android Device

  • Locate the Smart Life Smart app in the App store on your device.

  • Read and Agree to the User Agreement and Privacy Policy

  • Follow the directions to create a user account. Take note of your password.

  • Once Registered, Log In using your credentials.

Add your Bulldog into the Smart Life App

  • Select Add Device or tap the (+) symbol.

  • Allow Precise Location services so that Smart Life can find your WiFi Network and search for nearby devices.

  • Selecting Approximate location may result in an error

Your Bulldog will be added via Bluetooth

  • You will likely see a message to turn on Bluetooth. This comes up even if Bluetooth is turned on but “Nearby Devices” is not allowed.

  • Tap on ‘Turn on Bluetooth’ to allow Smart Life to use Bluetooth to help the Smart Life App to locate the Smart Life enabled Bulldog controller.

  • Notice there are sections for “Nearby Devices” and “Bluetooth.

  • Double check Nearby Devices is enabled in the App permissions in your device settings and Bluetooth is turned on

Put your Bulldog into Pairing Mode

  • On the Bulldog Controller, if the Blue Wifi Pairing LED is not flashing, hold down the Valve Open/Close for 6-8 seconds then release it. The Blue LED should start flashing momentarily.

  • Once in pairing mode, if permissions are all set correctly, your Smart Life enabled Bulldog soon will show up as a discovered device. Tap on it to add it.

  • First the add device screen will show, then you will be asked for your WiFi information.

  • Your Phone must be connected to the network that you want your Smart Life enabled Bulldog to use. This info will be populated for you.

  • Enter in your WiFi password, be careful of Upper Case / Lower Case and be sure there are no spaces.

  • Wait for the Add Device process to finish.

  • When the device is added successfully, tap the pencil icon on the right to rename it to something meaningful. Example: Bulldog Water Valve.

  • You can now monitor and Open/Close your Smart Life enabled Bulldog from anywhere on your phone or tablet.

Creating Notifications for your Smart Life enabled Bulldog

  • Smart Life will recommend Scenes for your Bulldog.
    You can ignore these suggestions.

  • Tap the grey (>) symbol then the (x) symbol if present.

  • Tap Create Scene or use the (+) in the top right corner.

  • Tap Create Scene

  • We want to know when the valve closes so select ‘When device status changes

  • Select your Bulldog Device. It will appear with the name you chose when you paired it to the App. Example: Bulldog Water Valve

  • Currently Smart Life treats your Bulldog like a switch. In the next screen tap “Switch 1”

  • We want to know when the Bulldog turns off so tap on the OFF option.

  • The next screen should have the ‘If’ part populated. Now we need to tell Smart Life to send you a notification. Tap on the “Then” option.

  • From the options that pop up, select Send Notification

  • Right now, your free account supports the first option “Message Center”

  • Your scene should look like this: If [Your Valve] Switch 1 OFF Then Message Center On

  • Tap Save then Yes to enable your Scene.

  • Test your scene by turning your Bulldog Off.

  • If you don’t see your notifications, check that notifications are turned on for Smart Life in your phone settings.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals