H-KING Frenzy 1400mm EPO Sports Aerobatic With LED Lights Instruction Manual

H-KING Frenzy 1400mm EPO Sports Aerobatic With LED Lights

Specifications:

• Product Name: H-KING FRENZY
• Model Type: EPO SPORTS AEROBATIC MODEL WITH LED LIGHTS
• Wingspan: 1400mm

Product Usage Instructions

Assembly Instructions:

UNDERCARRIAGE:

Fix the undercarriage halves into position with the four 2.6 x \12mm self- tapping screws. Ensure the legs are angled towards the front of the fuselage.

HORIZONTAL STABILIZER:

Remove the tab at the end of the fuselage, slide the horizontal stabilizer into the slot, align the holes, and use foam glue if \desired for security.

VERTICAL STABILIZER & RUDDER:

Install the vertical stabilizer and rudder assembly, ensuring the correct placement of the tail-wheel control wire. Use foam glue for security.

HORIZONTAL AND VERTICAL STABILIZER FIXING:

Fix stabilizers in position with provided screws, ensuring they are tightened sufficiently but not over-tightened.

TAIL CONTROL HORNS:

Connect rudder and elevator snap-links to control horns. Make minor adjustments for neutral positions if needed.

WING ASSEMBLY:

Join wing panels using carbon wing spar and plywood joiner. Glue wing panels together, ensuring correct wire routing. Secure the joint with tape and screws.

FAQ

• Q: Is this model suitable for beginners?
  • A: No, this model is not recommended for beginners and requires skill to fly.
• Q: Can children operate this model alone?
  • A: No, children should not operate this model without supervision from an experienced adult.
• Q: Can the specifications of this model change?
  • A: Yes, HobbyKing reserves the right to modify the specification of this model at any time.

WARNING

This radio-controlled model is not a toy. It requires skill to fly and is not recommended for use by beginners without assistance from an experienced model pilot. It should not be operated by children without the supervision of a suitably experienced adult. HobbyKing reserves the right to modify the specification of this model at any time.

SAFETY PRECAUTIONS

1. Do not attempt to repair or modify this aircraft with non-factory parts.
2. Never fly this model over roads, railway lines, power lines, airports, and do not fly this model in excessively strong winds, rain, or thunderstorms.
3. Do not fly or launch the model towards people.
4. Keep hands and face away from the rotating propeller at all times.
5. We strongly recommend that all fixings and fasteners used in the construction of this model are checked regularly for integrity. Failure to do so could cause a crash, injury to yourself or others around you.
6. We only recommend the use of 2.4GHz radio equipment with this model.

DISCLAIMER

1. This radio-controlled model is not a toy. Used incorrectly it is capable of inflicting serious injury to persons or damage to property. The owner/pilot assumes all responsibility for any damage to persons or property resulting from the use of this product.
2. The manufacturer and distributor decline all responsibility for any liability arising from use of this product.
3. It is very important that you follow all instructions for assembling and the setting up of this model. Failure to do so could result In a loss of control and possibly a crash.

EPO

EPO foam is a very tough and durable material perfect for the manufacture of model aircraft. When using screwed fixings with EPO components it is important to tighten the screws only enough to provide a firm fixing, do not over- tighten. Excess tightening could result in the foam material becoming compressed, possibly damaging or distorting the part. Take care to ensure that all screws are tightened sufficiently to provide a firm fixing, do not over- tighten. We recommend that all fixings are checked regularly for security and safety purposes.

INTRODUCTION

The Frenzy offers a stunning combination of terrific looks and a sensational flight performance. Manufactured from tough EPO it is extremely robust, however, in the event of a “less than perfect” arrival, we supply a range of spares to get you flying again in the shortest time. It is capable of a wide range of amazing aerobatic maneuvers to thrill the experienced pilot, but with reduced control throws it provides a solid and predictable flight performance, this makes it perfect for the sports and early solo pilots. We are certain you will enjoy your new model, please take the time to read this manual thoroughly and understand its contents completely prior to commencing assembly.

FEATURES

• Powerful Brushless Motor
• 40A Brushless Electronic Speed Controller
• Efficient 2 Blade 12×8 Propeller
• Chrome Finish Spinner
• Pre-Installed Servos
• Pre-hinged Control Surfaces
• Durable EPO Construction w/Carbon Reinforcement
• Plastic Cover on Cowl for Protection
• Steerable Tail Wheel
• Superb Flight Performance
• Excellent Power to Weight Ratio on 3S Set-up
• Very Bright LED Lighting System
• High-Viz Color Scheme

SPECIFICATION

• Wingspan:1400mm
• Length: 1130mm
• Weight: 1480g
• Motor: 3720-880KV Out-Runner Brushless
• Battery Required: 2200 – 2400mAh 11.l V LiPo (Not Included)
• Recommended Battery: 2200mAh 11.1 V 40C or greater
• ESC: 40A Brushless
• Servos: 2 x 9g, 2 x 17g
• Wing Loading: 40.3g/dm2

ASSEMBLY INSTRUCTIONS

UNDERCARRIAGE

Fix the undercarriage halves into position with the four 2.6 x 12mm self- tapping screws as shown in ( A). If the screws become excessively tight whilst fixing, simply back them off a tum or two, and then continue. Note: The undercarriage legs are angled towards the front of the fuselage.

HORIZONTAL STABILIZER

Remove the molded tab at the end of the fuselage with a sharp knife (B). Slide the horizontal stabilizer into the fuselage slot as shown (C). Make certain that the holes in the stabilizer line up with the corresponding fuselage holes. If desired, a small amount of foam glue can be used for maximum security.

VERTICAL STABILIZER & RUDDER

Install the vertical stabilizer and rudder assembly into the slot in the fuselage. Please make certain that the tail-wheel control wire is located correctly in the plastic hole in therudder slot as shown (D). If desired, a small amount of foam glue can be used for maximum security.

HORIZONTAL AND VERTICAL STABILIZER FIXING

Fix the horizontal stabilizer and vertical stabilizer in position with the two 2.6 x 35mm screws provided, (E). The screws must be tightened sufficiently to securely fix the parts in position, however be careful not to over-tighten the screws.

2 x screws 2.6 x 35mm

TAIL CONTROL HORNS

Connect the rudder and elevator snap-links to their respective control horns as shown in images F & G. Minor adjustment to obtain perfect neutral positions of the control surfaces can be achieved by rotating the plastic link on the threaded portion of the control push-rod. Make certain the plastic link is securely “snapped” closed when connected to the control horn.

WING ASSEMBLY

Locate the 500mm carbon wing joining spar and slide it into the round aperture of one wing panel. Locate the small plywood rear wing joiner and insert it into the rectangular aperture behind the main wing spar (H). Slide the remaining wing panel onto the exposed portion of the carbon spar. The plywood locking plate will ensure perfect alignment of the two wing halves. It is highly recommended that the joint of the wing panels is glued together for maximum security. Apply glue to the roots of the wing panels and push them together, be careful that all the wires are routed correctly via the molded slots, and that they do not foul the joint between the wing roots. Once the joint is together, temporarily wrap some tape around the joint, then screw the wing to the fuselage to ensure the perfect fit. Once the glue has dried, remove the wing and then the tape.

The Frenzy is supplied with a unique 4 way lead for joining the aileron servos and the LED lights. Connect two of the 4 leads to the aileron servos, and two of the leads to the LED lights as shown (J). The other single lead goes to the aileron port in your chosen receiver.

WING FIXING

Insert the front and rear plastic connectors into the wing, (K). They are angled to provide a perfect fit. Make certain you have them located correctly! The wing can now be fixed in position onto the fuselage using the three M4 x 50mm screws provided

PROPELLER & SPINNER

1. Remove the propeller set out of its packaging.
2. Disassemble the spinner using a screwdriver.
3. Install the propeller assembly onto the motor shaft as shown in illustration (L).
4. Using a wrench on the adapter nut, tighten the assembly onto the motor shaft.
5. Re-assemble the spinner to the propeller assembly using the 2 screws.
6. Assembly of propeller unit is completer. \Securely tightening the nut will clamp the adapter to the motor shaft and fix the propeller in position. Note: Use of excessive force will cause damage to the aluminum adapter.
   Note: It is essential that the propeller is securely fixed. Failure to do so could result in serious injury.

RECEIVER INSTALLATION

Connect the speed controller to the throttle channel of your receiver, (not included). This wire is easily identified, it is the only one that is routed from the front of the model. Connect the rudder and elevator servos to the corresponding channel outputs of the receiver and connect the plug on the 4 way lead to the aileron channel output. There is a molded recess in this compartment which is sufficient to accommodate most popular 2.4GHz receivers; however there is ample room elsewhere to locate yours if it does not fit in the recess. We recommend that it should be securely positioned with self- adhesive hook and loop tape. You must adhere to the receiver manufacturer recommendations regarding positioning and aerial routing.

BATTERY INSTALLATION

The battery compartment is accessed by gently squeezing the two raised white tags and lifting the rear of the front hinged cover, (M). Your flight battery, (not-included) can easily be installed and connected to the factory fitted XT60 connector, (N). Make certain the battery and cover are both secure before flight, the battery compartment has been made bigger to except larger batteries if required, if your battery is loose in the compartment please use some foam sponge packing to keep it in place.

CONTROL SURFACES

Check that all control surfaces are centered and responding correctly to transmitter inputs. Adjustments can be made to control surface centers by carefully rotating the plastic control links on the threaded portion of the metal control rods. Use the servo reversing function on your transmitter for any control that is not responding in the correct sense to control inputs. Make certain that all plastic links are securely “snapped” closed and that all control surface hinges are\ secure. Use a small amount of foam glue if any hinges are not firmly attached.

PROPELLER ROTATION

Double-check that the propeller is securely fixed and it is rotating in the correct direction, (P).

CENTRE OF GRAVITY

It is vital that you check that the center of gravity is correct. Failure to do so could result in a complete loss of control. We recommend the balance point of the model, complete with battery, should be 75 -90mm back from the leading edge of the wing for initial flights, (Q). Very experienced pilots may wish to move the balance point further back after initial flight testing.

CONTROL SURFACE DEFLECTIONS

We suggest the following recommendations for control surface deflections. Experienced pilots may wish to increase these movements after initial flight testing.

• Ailerons: 10mm each way.
• Elevator: 10mm each way.
• Rudder: 12mm each way.

We hope you enjoy many happy and safe flights with your new H-King Frenzy model aircraft. Check-out the other aircraft in the H-King range at www.hobbyking.com.

SPARE PARTS

A FULL RANGE OF SPARE PARTS IS AVAILABLE FOR THE FRENZY

RECOMMENDED ACCESSORIES

UK REP

• APEX CE SPECIALISTS LIMITED 89 Princess Street, Manchester, M1 4HT, UK

EC REP

• APEX CE SPECIALISTS LIMITED Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, T23 AT2P, Ireland

References

• Radio Control Planes, Drones, Cars, FPV, Quadcopters and more - Hobbyking

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>