URC UR2-DTA DTA Remote Control Instruction Manual

: June 12, 2024
: URC

Table of Contents

URC UR2-DTA DTA Remote Control
Introduction
Replacing Batteries
Operations
Programming the Remote Control
A. Quick Set-Up Method
B. Quick Set-up Code Tables
C. Pre-Programmed 3-Digit Code
Auto-Search Method
E. Finding a Component Button’s
F. Programming Volume Control
Setup Code Tables
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

URC UR2-DTA DTA Remote Control

UR2-DTA DTA Remote Control
The UR2-DTA is a universal remote control designed to operate S/A, Pace Micro, Motorola, and IPTV set tops, as well as the majority of TV equipment on the market. It provides convenient control over your DTA box, IPTV set tops, and televisions.

Replacing Batteries

Before programming or operating the remote control, you need to install two new AA alkaline batteries. Follow these steps:

Remove the battery compartment cover on the back of your remote control.
Check battery polarity carefully and install the batteries as shown in the illustration below.
Replace the battery compartment cover.

Operations
The default setting for volume control is through the DTA. However, you have the option to control volume and mute through your TV. Refer to Section F for programming instructions.

Button Functions
The remote control offers various button functions to control your devices.

Programming the Remote Control
There are three methods to program your remote control:

Quick Set-Up Method
Pre-Programmed 3-Digit Code Method
Auto-Search Method

IMPORTANT SETUP NOTE!
During setup mode, the DTA LED will light for 20 seconds. If you don’t press a button within this time, the LED light will turn off and exit setup mode. You will need to start over.

Quick Set-Up Method

Turn on the component you want to program. For programming the TV, turn on the TV.
Press and hold the [DEVICE] key for 5 seconds until the DTA LED blinks once and stays on.
Continue holding the [DEVICE] key and press the number key assigned to your brand in the Quick Set-up Code Table.
Release both the [DEVICE] key and the number key to save the code. The DTA LED will blink twice to confirm that the code is stored.
Point the remote control at the component.
Press the power button. If the component turns off, it is successfully programmed. If not, proceed with the Pre-Programmed 3-Digit Code Method or Scanning Method.
Repeat the above steps for all components (DTA, TV).

B. Quick Set-up Code Tables
Use the Quick Set-up Code Tables below to find the number associated with your brand:

DTA Quick Number	Manufacturer/Brand
0	PACE DTA
1	SA/CISCO, SAMSUNG, PACE DIGITAL
2	MOTOROLA DIGITAL
3	MOTOROLA DTA
4	EVOLUTION DTA
5	CISCO IPTV
6	ADB IPTV
7	TECHNICOLOR
8	AMINO 140/540 IPTV
9	MOTOROLA IPTV
TV Quick Number	Manufacturer/Brand
---	---
0	SANYO
1	SONY
2	SAMSUNG
3	LG
4	TOSHIBA
5	PANASONIC
6	PHILIPS
7	HITACHI
8	SHARP
9	VIZIO

C. Pre-Programmed 3-Digit Code Method

Turn on the component you want to program (TV, DTA).
Press the [DEVICE] button (TV or DTA) to be programmed and the [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds, indicating that the unit is ready to be programmed.
Point the remote control toward the component and enter the 3-digit code number assigned to your brand.
If the component turns off, the entered code is correct. If it doesn’t turn off, continue entering code numbers listed for that brand until the component turns off.
Once you find the correct code, save it by pressing the same [DEVICE] button one more time. The DTA LED light will blink twice to confirm that the code was successfully stored.

Now you can enjoy controlling your devices using the UR2-DTA DTA Remote Control!

Introduction

The UR2-DTA is designed to operate the S/A, Pace Micro, Motorola and IPTV set tops, plus the majority of TV equipment on the market as shown below.

DTA : DTA boxs, IPTV set tops
TV : Televisions

Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries.

STEP1 Remove the battery compartment cover on the back of your remote control.
STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.

Operations

Volume Default: DTA volume and mute through the DTA, with the option of controlling volume and mute through the TV. Refer to Section F for programming the volume and mute through your TV.

Button Functions URC-UR2-DTA-DTA-Remote-Control-01

Programming the Remote Control

There are three ways you can program your remote:

Quick Set-Up Method
The Pre-Programmed 3-Digit Code Method
The Auto-Search Method

The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using one-digit codes for up to 10 major brands for each component.
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all the codes in the remote control, one at a time.

IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, the DTA LED will light for 20 seconds. If you do not press a button within 20 seconds, the LED light will turn off and exit setup mode and you will need to start over.

A. Quick Set-Up Method

STEP1 Turn on the component you want to program. To program your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key for 5 seconds until the DTA LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Set-up Code Table and release both [DEVICE] key and the number key to save the code. The DTA LED will blink twice to confirm that the code is stored.
STEP3 Point the remote control at the component.
STEP4 Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre-Programmed 3-Digit code Method or Scanning Method.

Repeat the steps above for all components. (DTA, TV).

B. Quick Set-up Code Tables

DTA

0	PACE DTA
1	SA/CISCO, SAMSUNG, PACE DIGITAL
2	MOTOROLA DIGITAL
3	MOTOROLA DTA
4	EVOLUTION DTA
5	CISCO IPTV
6	ADB IPTV
7	TECHNICOLOR
8	AMINO 140/540 IPTV
9	MOTOROLA IPTV

TV

Quick Number	Manufacturer/Brand
0	SANYO
1	SONY
2	SAMSUNG
3	LG
4	TOSHIBA
5	PANASONIC
6	PHILIPS
7	HITACHI
8	SHARP
9	VIZIO

C. Pre-Programmed 3-Digit Code

Method

STEP1 Turn on the Component you want to program(TV, DTA).
STEP2 Press the [DEVICE] button (TV or DTA) to be programmed and [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds indicating the unit is ready to be programmed.
STEP3 Point the remote control toward the Component and enter the 3-digit code number assigned to your brand.
*Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off.
STEP4 Once you have found the correct code, save it by pressing the same [DEVICE] button one more time. The DTA LED light will blink twice to confirm that the code was successfully stored.

Auto-Search Method

STEP1 Turn on the Component you want to program (TV, DTA).
STEP2 Press the [DEVICE] button (TV or DTA) to be programmed and [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds indi-cating the unit is ready to be programmed.
STEP3 Point the remote toward the Component and press the [CH5] or [CH6] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH5] or [CH6] button as soon as the Component turns Off.
STEP4 Once you have found the correct code, save it by pressing the same [DEVICE] button one more time. The DTA LED light will blink twice to confirm that the code was successfully stored. Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method.

E. Finding a Component Button’s

Setup Code Number
If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference.

STEP1 Press the [DEVICE] button (TV or DTA) you want to verify and the [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds.
STEP2 Press the [INFO] button and count the number of times the DTA LED light blinks. This num-ber indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off.
- *Note : 10 blinks represents the number zero.
- Example : One blink, (pause), eight blinks, (pause) and three blinks, indicates code number 183.

F. Programming Volume Control

By default, the VOL+, VOL- and MUTE keys operate through your DTA. If you would like those keys to operate those functions on a TV device, follow these steps.

STEP1 Press the [SEL] button and [DTA] button simultaneously for 3 seconds.
- The DTA LED will turn on for 20 seconds.
- The next step must be perfumed while the LED is on.
STEP2 Press the [VOL+] button.
- The DTA LED will blink.
STEP3 Press the [TV] button that you would like the volume and mute buttons to control. The DTA LED will blink twice to confirm the programming.

Note : If you wish to have the volume and mute keys operate your DTA Box, press the [DTA] device button in Step 3.

G. Memory Lock System
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

H. Write your TV Set-up codes
Set-up Code Number : For additional information about your remote control, go to www.universal-remote.com

Setup Code Tables

DTA

SCIENTIFIC ATLANTA	003 251
PACE	001 003 204 206 217 002
MOTOROLA	001 206 253
ADB	254 255 315 259
Amino	219 260 249 256 257 261 235
ARRIS	192 216 140 234 242
AT&T	251
BELL FIBE	205 229
Blue Stream	138
BT Vision	232 960
CHANNEL MASTER	006
CINCINNATI BELL	194 220
CISCO	007 003 005 002 251 316
COMCAST	195 002
CONFLUENT	196
Cox Digital Cable	223
Digital Multimedia Technology	222
DIGITAL STREAM	580
DIRECTV	238
Dish Network	122
Duoson	218
DVB (Digital Video Broadcasting)	193
Entone	221 155 258 213

DTA

Manufacturer/Brand	Set-Up Code Number
EVOLUTION	189 215
Foxtel	228
Frontier	139
HOMECAST	004
Horizon	225
Humax	231
Innovative Systems	262
Layer3	226
MINERVA	178
MOXI	111
MYRIO	254 255
NAGRAVISION	201
NBOX	181
NOW TV	314
Optimum	236 237
Pico Digital	224
SAMSUNG	003
Sky	240 241
Spectrum	231
SUDDENLINK	579
TECHNICOLOR	365 002
THOMPSON	365 002
TRANSPARENT VIDEO SYSTEMS	193
Virgin Media	959
WEGENER	250
WINDSTREAM	212
ZeeVee	227

TV

Manufacturer/Brand	Set-Up Code Number
ADMIRAL	072 081 160 161 096
AD NOTAM	672
ADVENT	147 224
AFFINITY	680
AIWA	238 141 145
AKAI	031 070 146 004 148 124 226

104 108 615

TV

Manufacturer/Brand	Set-Up Code Number
AQUAVISION	164 686 904
ASTAR	164
AUDIOVOX	076 103 043 035 224 228 078
AUVIO	689
Avera	761
AVION	223
AWOL Vision	905
AXESS	711
AXION	043
BAYSONIC	043
BELL&HOWELL	072
BENQ	600
BRADFORD	043
BROKSONIC	231 252 096 170
BYDESIGN	254
CAIRN	162
CANDLE	070 002 003 004
CANON	236
CAPEHART	058
CARVER	164
CELEBRITY	001
CETRONIC	043
CIELO	101
Ciil	732
CINERAL	103 120
CITIZEN	070 002 003 004 101 103 127
CLASSIC	043
COBY	640 641 671 004
CONCERTO	004
CONTEC	043 051
Continu-us	161 746 747
CORONADO	127
CRAIG	043 054 028 239
CROSLEY	164
CROWN	043 127
CURTIS MATHES	070 004 101 127 236 011 072