ca Go FS200 Life Mounting Set for ISOFIX Compliant Child Seats Instruction Manual
- June 12, 2024
- Ca Go
Table of Contents
ca Go FS200 Life Mounting Set for ISOFIX Compliant Child Seats
Safety Notices
This user manual contains various types of notice.
The notices are designed as follows:
Danger
Potential hazards for your health and the health of your co-riders and other
road users if you fail to observe the respective instructions or do not take
corresponding precautions.
Notice
Provides information about how to handle the product or refers to a passage in
the user manual that deserves special attention.
Caution
Warns you about incorrect behavior that can result in material and
environmental damage.
Separate instructions
Refers you to other assembly instructions for your FS200 Life which describe
the respective assembly step in more detail if needed.
General Information
The FS200 Life provides the option to install child seats that conform to the
ISOFIX standard (ISO 13216).
ISO 13216 offers a universal system for installing child seats in passenger
cars.
In addition to the dimensions of the physical interfaces, the standard
describes further requirements and test procedures. These generally refer to
the installation on the seat of a passenger car.
Applying this to the installation inside the box of a cargo bike is only
partly possible or even useful. We have designed the connection in such a way
that the bottom ISOFIX points are used for fastening and the child seat can be
placed in the transport box secured to these points.
Intended Use
The installation set is not compatible with the Ergonomic-Child-Seat, the Infant-Sling-Mount or the Original Protective Mat.
The compatibility of the installation set with ISOFIX child seats or base stations has to be tested in each individual case.
If the installation set is used, only one child can be transported in the transport box.
The screw connections should be checked for tight seat at regular intervals and retightened as required.
When installing ISOFIX-compatible child seats and base stations, the pertaining manufacturer’s instructions and provisions must be observed at all times.
Every child and every infant must be transported in a child seat or infant
carrier that is suitable for his or her specific height and weight. They must
be strapped in at all times.
The FS200 Life is designed for the transport of up to two children/ infants.
Transporting infants and children with the box closed is not permitted.
When transporting infants and children, the transport box lid must not be
installed.
Scope of Delivery
-
EPP block
1 piece
-
Long plate
2 pieces
-
Short plate
2 pieces -
Tommy screw
2 pieces
No additional tools are required for the installation.
Installation
The connection plates are first mounted to the bottom transport box rail
located at the rear in the direction of travel. To do this, place the long
plate 2 around the rail so that the rectangular notch points to the front and
up in the direction of travel.
The connection is now clamped to the rail by using the short plate 3 and the
tommy screw 4 . Tighten the screw connection only very slightly to enable
alignment at a later time (Figs. 3 and 4).
Place the EPP block 1 in the transport box, with the cut-out section facing
up.
The profile on the bottom side of the EPP block engages with the profile in
the floor of the transport box and thus prevents the block from sliding
around.
Align the connection plates so that they can be reached at a distance of 10–15
mm above the EPP block (Fig. 5).
The arrows on the block indicate how to align the connection plates laterally
(Fig. 6). Following the correct alignment, tighten the tommy screws hand-
tight.
Hook the child seat and the base plate into the connection plates in
accordance with the manufacturer’s instructions and push them into the wall of
the transport box so that the closure is securely engaged (Figs. 7 to 10).
If a child seat is installed instead of a base station, the procedure is the same. Always observe the manufacturer’s instructions.
General Notes On Care
The cleaning and care requirements for the EPP block are the same as for the transport box. In many cases, water is all that is needed to do the job. If needed, you can use a mild detergent, such as dishwashing liquid or hand soap.
Never use aggressive cleaning agents, acids or solvents to clean the set. Such
substances can corrode or damage surfaces.
This may affect the stability of the components.
Statutory Warranty / Guarantee
The legal statutory warranty applies. You can find more details on the
warranty on our website:
www.cagobike.com/en/warranty
Export to the USA and Canada is not permitted (product liability)!
Service
If you have questions concerning this user manual, please contact your Ca Go dealer or your Ca Go service team.
Customer Support
Ca Go Bike GmbH
Am Autobahnkreuz 7
56072 Koblenz
Germany
+49 261 914090-600
info@cagobike.com
www.cagobike.com
Managing directors: Franc Arnold
Company register
Court of record: District Court Koblenz / register no.: HRB 26998 / VAT Id no.
DE326206636
Responsible for distribution and marketing of the user manual: Ingo Kahnt Ca
Go Bike GmbH reserves the right to change product specifications without prior
notice.
Typographical errors, mistakes and modifications reserved. Version of 03/2023
©Reproduction, reprint and translation, as well as any use for economic
purposes (including as extracts, in print or electronic form)
without prior written approval is forbidden.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>