QSFPTEK S5300-48S6X 48 Port 1Gb SFP Ethernet L3 Switch User Guide

QSFPTEK S5300-48S6X 48 Port 1Gb SFP Ethernet L3 Switch User Guide

Introduction

The S5300-48S6X Switch is a high-performance 1G/10G switch. The product position is to meet the requirements of telecom IP, cyber cafes, and diskless working environments.

We appreciate your decision to select S5300-48S6X. This manual is intended to help you become acquainted with the switch design and provide instructions for implementing the switches into your network

Accessories

• **Power Cord x1

**

• **Console Cable x1

**

• **Mounting Bracket x2

**

• **M3 Screw x6

**

• **Rubber Pad X4

**

Hardware Overview

Front Panel Ports

Front Panel LEDs

Back Panel

Installation Requirements

Tools Preparation

• Screwdriver
• Static-proof wristband
• Bolt
• Ethernet cable
• Other Ethernet terminal devices
• Control terminal

Safety Principles

Keep dustless and clean during or after the installation

• Put the cover at the safe place.
• Put tools at the right place where they are not easily falling down.
• Put on relatively tight clothes, and fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
• Put on the protective glasses if the environment may cause damage to your eyes.
• Avoid incorrect operations that may cause damage to human or devices.

Site Environment

• Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged and sufficient air circulation is provided for device cooling.
• Avoid to damage devices by following the electrostatic discharge prevention procedure.
• Put the chassis at the place where cool air can blow off the heat inside the chassis. Make sure the machine box is sealed
  because the opened machine box will reverse the cool air flow.

Mounting the Switch

Connecting the Power

1. Plug the AC power cord to the switch power port on the back rear.
2. Connect the other end of the power cord to a AC power source equipment.

Connecting the SFP Port

1. Insert the SFP module into the SFP port.
2. Plug a fiber patch cable to the SFP transceiver.
3. Connect the other end of the fiber to the device that you want to realize data communication.

Connecting the SFP+ Port

1. Insert the SFP+ module into the SFP+ port.
2. Plug a fiber patch cable to the SFP+ transceiver.
3. Connect the other end of the fiber to the device that you want to realize data communication.

Connecting the Management Ports

Connecting the Console Port

1. Prepare an console cable.
2. Insert the RJ45 connector of the console cable into the console port on the switch.
3. Connect the D89 female connector on the other end of the console cable to the serial port on the computer host

Configuring the Switch

Configuring the Switch Using the Web-based Interface

Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.
Step 2: Set the IP address of the computer to 192.168.0.x (where “x” is any number from 2 to 254) and the subnet mask to 255.255.255.0

Step 3: Open a web browser and type http://192.168.0.2 in the address bar. Enter the default username and password (admin/admin).
Step 4: Click sign-in to access the web-based configuration page.

Configuring the Switch Using the Console Port

Step 1: Use the console cable to direct connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control.

Step 4: Enter the default username and password (admin/admin).

Troubleshooting

The key for resolving the systematic faults is to separate the fault from the system. You can compare what the system is doing with what the system should do to detect the fault. You need to check the following subsystems:

Faults Relative with Power and Cooling System

Do the following checkups to help remove the fault:

Check whether the fan works normally. If the fan does not work well, check the fan.

If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section “Requirements for Common Locations”.

If the switch cannot be started and the PWR indicator is off, check the power

Faults Relative with Port, Cable and Connection

Do the following checkups to help remove the fault:

If the port of the switch can not be linked, check whether the cable is correctly connected and whether the peer connection is normal.

If the power switch is at the “ON” location, check the power source and the power cable.

If the console port does not work after the system is started up, check whether the console port is set to a  baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.

Support and Other Resources

• Contactus https://www.qsfptek.com/company/contact-us.html
• Email sales@qsfptek.com
• Customer Success https://www.qsfptek.com/resources/customer-success-stories

Product Warranty

S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or exchange of your items within 14 days of receiving them.

For more details about applying qualifications, please live chat or email sales@qsfptek.com for support.

5 Years Warranty

14-day Return Window

Documents / Resources

| QSFPTEK S5300-48S6X 48 Port 1Gb SFP Ethernet L3 Switch [pdf] User Guide
S5300-48S6X, S5300-48S6X 48 Port 1Gb SFP Ethernet L3 Switch, 48 Port 1Gb SFP Ethernet L3 Switch, 1Gb SFP Ethernet L3 Switch, SFP Ethernet L3 Switch, Ethernet L3 Switch, L3 Switch, Switch
---|---
| QSFPTEK S5300-48S6X 48 Port 1Gb SFP Ethernet L3 Switch [pdf] User Guide
S5300-48S6X, S5300-48S6X 48 Port 1Gb SFP Ethernet L3 Switch, 48 Port 1Gb SFP Ethernet L3 Switch, 1Gb SFP Ethernet L3 Switch, SFP Ethernet L3 Switch, Ethernet L3 Switch, L3 Switch, Switch

References

• QSFPTEK - Compatible Optical Transceivers Factory Outlet
• Customer Success Stories - QSFPTEK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>