AtlasScientific EZO Complete-TMP USB Temperature Meter User Guide
- June 12, 2024
- AtlasScientific
Table of Contents
AtlasScientific EZO Complete-TMP USB Temperature Meter
Product Information
The EZO Complete-TMP is a USB Temperature meter designed and manufactured by AtlasScientific. It is a dustproof and splash-resistant device with a USB connector and a probe connector. The readings provided by the EZO Complete-TMP are interference-free and unaffected by other sensors in the same water. The device can read temperatures from any type and brand of PT-100 or PT-1000 temperature sensors with single-point accuracy. The readings are displayed at a rate of 1 reading per second.
Product Usage Instructions
To use the EZO Complete-TMP, follow these instructions:
- Ensure that the USB connector and the probe connector are free from water or any other liquid. Water entering the USB connector can cause an electrical short and permanently damage the device. Water entering the probe connector can cause a temporary connector to short, affecting temperature readings and potentially damaging the temperature probe.
- Connect the EZO Complete-TMP to your computer using the USB connector.
- Install the AtlasDesktop monitoring software on your computer.
- Once the software is installed, open it and click on the gear icon to access the setup options.
- Follow the on-screen calibration steps to calibrate the device. Make sure to issue calibration commands only when the readings have stabilized to avoid drifting readings.
- If you want to link the temperature readings from the EZO Complete-TMP to other EZO-Complete sensors for temperature compensation, navigate to the advanced setup options in the software. You can link the temperature readings to other sensors’ readings, such as conductivity, for temperature-compensated measurements.
Note: For detailed instructions on specific setup procedures or troubleshooting, refer to the product manual or check for updates on the manufacturer’s website.
OVERVIEW
- Reads Temperature
- Range -126.000 °C to 1254 °C
- Accuracy +/– (0.1 + 0.0017 x °C)
- Temp reading time 1 reading /sec
- Supported probes Any type & brandB PT-100 or PT-1000
- Calibration Single point
Interference-free
The EZO complete readings are unaffected by other sensors in the same water.
Ingress protection IP62
The EZO Complete-TMP™ is dust proof and resistant to splashing water. Two
areas of concern are the USB connector and the probe connector.
Ingress protection IP62
An electrical short can occur if water enters the USB connector. A USB
short could permanently damage the EZO-Complete. A USB short is not covered
under warranty.
A connector short can occur if water enters the SMA connector. A connector
short will cause the temperature readings to pin to -1023, or the probe will
respond slowly to changes in temperature. A connector short is reversible and
will not damage the EZO-Complete. However, frequent shorts will eventually
damage the temperature probe .
The SMA connector is part of your probe; Nothing should be in contact with this part.
Do not use this as a mounting point!
Setup
- Temperature probe with SMA Connector
- Temperature probe with BNC Connector
- Micro Temperature probe with SMA Connector
- Tinned leads with the SMA to terminal block connector
Setup
Once you have installed the AtlasDesktop monitoring software, you can begin
monitoring and logging your readings.
Best practices for calibration
Always watch the readings throughout the calibration process. Issue calibration commands once the readings have stabilized.
Never do a blind calibration! Issuing a calibration command before the readings stabilize will result in drifting readings
Calibration procedure
Advanced setup
The EZO-Complete-TMP readings can be linked to other EZO-Complete sensors to
provide temperature compensation to the other sensors readings.
Example: We setup an EZO-complete monitoring system to read conductivity
and temperature.
Entering the conductivity setup page, you can link the readings from your EZO-
Complete temperature sensor to your conductivity readings, this will give you
temperature compensated conductivity readings.
The connected EZO-complete-TMP is the device with address 129. If multiple
temperature sensors are connected, multiple address will be listed. (The
temperature sensor address is listed in the temp sensor setup page) Copyright
© Atlas Scientific LLC
PATENT PROTECTED: This is an evolving document, check back for updates.
Written by Jordan Press Designed by Noah Press
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>