Spectrum SR-002-R Remote Control User Guide
- June 12, 2024
- SPECTRUM
Table of Contents
Spectrum SR-002-R Remote Control
Install Batteries
- Apply pressure with your thumb and slide the battery door to remove it
- Insert two AA batteries. Match the + and – marks.
- Slide the battery door back into place.
Setup for Popular TV Brands
This step covers setun for the most common TV brands. If vour brand is not listed. please proceed to PROGRA ING YOUR REMOTE FOR TV AND AUDIO CONTROL.
- Ensure that your TV is powered on.
- Simultaneously press and hold MENU and OK keys on remote until the INPUT key blinks twice.
- Press and release the TV POWER key once.
- Find your TV brand in the chart to the right and note the digit that relates to your TV brand. Press and hold down the digit key
- NOTE: When you hold the digit key, the remote will test for the working IR code, causing the INPUT key to flash each time it tests a new code.
- Release the digit key when the TV turns off. Setup is complete. If this was not successful or if you have an audio device in addition to your TV, please proceed to program YOUR REMOTE FOR TV AND AUDIO CONTROL.
| Digit | TV Brand |
|---|
Insignia/ Dynex
2| LG/ Zenith
3| Panasonic
4| Philips/ Magnavox
5| RCA/ TCL
6| Samsung
7| Sharp
8| Sony
9| Toshiba
0| Vizio
Troubleshooting
- Problem: The INPUT key blinks, but the remote doesn’t control my equipment.
- Solution: Follow the programming process in this manual to set up your remote to control vour home theater equipment.
- Problem: The INPUT key doesn’t light up on the remote when I press a key.
- Solution: Ensure that the batteries are functional and inserted properly. Replace the batteries with two new AA-size batteries.
- Problem: My remote won’t control my equipment.
- Solution: Be sure that you have a clear line of sight to your home theater equipment.
Remote Key Chart
Programming Your Remote for TV and Audio Control
This step covers setup for all TV and audio brands. For faster setup, be sure to locate your device brand in the code list before beginning setup.
- Ensure that your TV is powered on.
- Simultaneously press and hold MENU and OK keys on remote until the INPUT key blinks twice.
- Enter the first code listed for your brand. The INPUT key will blink twice to confirm when complete.
- Test volume and TV power functions. If the device responds as expected, setup is complete. If not, repeat this process using the next code listed for your brand. If you have an audio device in addition to your TV, please repeat steps 1-4 listed here with vour audio device
Declaration of Conformity
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by the turning of equipment off
and on, the user is encouraged to try to correct the interference by one of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The user is cautioned that the changes and modifications made to the equipment without the approval of the manufacturer could void the user’s authority to operate this equipment.
Setup Codes For Audio – Amplifier Setup Codes For Audio – Accessory
Setup Codes For Audio – Receiver
Setup Codes For Television
