DATALOGIC A22 Mobile Computer Scanner User Guide
- June 12, 2024
- DATALOGIC
Table of Contents
DATALOGIC A22 Mobile Computer Scanner
OUT OF THE BOX
The Joya Touch 22 package contains:
- Joya Touch 22 (device with battery included)
- Quick Start Guide
- Safety & Regulatory Addendum
Remove all the components from their packaging; check their integrity and compare them with all the packing documents.
CAUTION: Keep the original
packaging for use when sending products to the technical assistance center.
Damage caused by improper packaging is not covered under the warranty.
GENERAL VIEW
Front View
Back View
NOTE: The label artwork may be only a draft. Please refer to the label attached to the product for information about certification marks.
Top View
Side View
Handheld Models
Pistol Grip Models
CHARGING INSTRUCTIONS
The Joya Touch 22 is provided with the battery pack already installed and configured in Ship Mode at the factory. To wake the device from Ship Mode, connect it to a power supply or insert it into a dock (for more information, see the Getting Started section of the Joya Touch 22 User’s Manual). The battery pack is initially not fully charged. Before using the device, charge the battery with the single slot dock locking, the single slot dock charge only, the 3-slot cradle or the Data logic USB-C type power supply.
Charge with the Single Slot Dock Locking
First plug the power cord into the power connector on the back of the dock,
then connect the power cord to the power supply.
CAUTION: Use only the Datalogic
power supply 91ACC0048 to power the Joya Touch Single Slot Dock Locking.
The Single Slot Dock Locking cannot be daisy-chained to a Joya Touch 3-Slot
Cradle.
NOTE: Insert the device into the dock with the screen facing front and
the head facing down.
For further information on the Joya Touch Single Slot Dock Locking, refer to
the Single Slot Dock Locking Quick Start Guide, included in the dock’s box.
Charge with the Single Slot Dock Charge Only
First plug the power supply into the power jack on the back of the dock, then
plug the power supply into a power outlet.
You can also use the Type-A/Type-C cable (p/n94ACC0327) to charge the Joya
Touch 22 from any sell-powered USB hub or USB port on a computer.
CAUTION: Use only the Datalogic
power supply included in the box to power the Joya Touch Single Slot Dock
Charge Only.
NOTE: Insert the device into the dock with the screen facing front and the head facing down.
Charge with the 3-Slot Cradle
There are two options to connect the cradle to the power supply: fast charge
and standard charge.
Fast Charge
The fast charge connection allows to power one cradle with one power supply.
Plug the power supply cable into the power connector on the back of the
cradle, then plug the power supply into the AC/DC plug using a Datalogic power
cable. Please see below an example of how to insert the power supply cable
through the wall mounting metal bracket.
Standard Charge
The standard charge connection allows to power two cradles with one power
supply.
To connect a second cradle use the Joya Touch Cradle Power Jumper, available
as optional accessory (P/N 91 ACC0049).
- Connect the first cradle to the second cradle using the power jumper.
- Connect the power supply to the first cradle.
- Plug the power supply into the AC/DC plug using a Datalogic power cable.
CAUTION: Use only the Datalogic
power supply 91ACC0048 to power the Joya Touch 3-Slot Cradle.
NOTE: Insert the device into the dock with the screen facing front and
the head lacing down.
Under the same conditions, the fast charge connection can charge the battery
up to twice as fast as the standard charge connection.
For further information on the Joya Touch 3-Slot Cradle, refer to the Joya
Touch
3-Slot Cradle Quick Start Guide, included in the cradle’s box, and to the Joya
Touch
3-Slot Cradle Installation Guide, downloadable from our website www.datalogic.
com.
CAUTION: Do not put any foreign
object such as, but not limited to, coins, paper clips, stickers inside the
slot of any of the docks.
Do not apply any sticker to the Joya Touch 22 (see the examples below).
CHARGE WITH USB
Use the Datalogic USB-C type power supply (p/n94ACC0329) to charge the terminal from a power outlet.
SCANNING AND IMAGING
To scan a barcode symbol,
- Point the scan window at the barcode from a distance within the reading range.
- Press the Scan Key or the Scan Trigger. The imager projects a laser aiming pattern similar to those used on cameras. The aiming pattern is used to position the barcode or object within the field of view.
- Center the symbol in any orientation within the aiming pattern. Ensure the entire symbol is within the rectangular area formed by the brackets in the aiming pattern, then either wait for the timeout or release the Scan Key to capture the image. A red beam illuminates the symbol, which is captured and decoded.
If the scan has been successful:
- If enabled, the good read LED turns on.
- If enabled, the good read beep plays.
- If enabled, the Green Spot projects a green spot onto the barcode image.
- The barcode type and content data display on the screen.
Linear Bar Code
|
2D Matrix Symbol
---|---
Relative Size and Location of Aiming System Pattern
Datalogic S.r.l.
Via San Vitalino 13
40012 Calderara di Reno (BO)
Italy
Tel. +39 051 3147011
Fax+390513147205
©2022-2023 Datalogic S.p.A. and/or its affiliates
All rights reserved. Without limiting the rights under copyright, no part of
this documentation may be reproduced, stored in or introduced into a retrieval
system, or transmitted in any form or by any means, or for any purpose,
without the express written permission of Datalogic S.p.A. and/or its
affiliates. Owners of Datalogic products are hereby granted a non-exclusive,
revocable license to reproduce and transmit this documentation for the
purchaser’s own internal business purposes. Purchaser shall not remove or
alter any proprietary notices, including copyright notices, contained in this
documentation and shall ensure that all notices appear on any reproductions of
the documentation.
Electronic versions of this document may be downloaded from the Datalogic
website (www.datalogic.com).
If you visit our website and would like to make comments or suggestions about
this or other Datalogic publications, please let us know via the “Contact”
page.
REFERENCE DOCUMENTATION
For further information regarding the Joya Touch 22 refer to the SOK Help on- line, downloadable from our developer portal: https://developer.datalogic.com/mobile-computers.
SUPPORT THROUGH THE WEBSITE
Datalogic provides several services as well as technical support through its
website.
Log on to www.datalogic.com.
For quick access, from the home page click on the search icon Q., and type in
the name of the product you’re looking for. This allows you access to download
Data Sheets, Manuals, Software & Utilities, and Drawings.
Hover over the Support & Service menu for access to Services and Technical
Support.
CUSTOMER SUPPORT
©2022-2023 Datalogic S.p.A. and/or its
affiliates
• All rights reserved • Without limiting the rights under copyright, no part
of this documentation may be reproduced, stored in or introduced into a
retrieval system, or transmitted in any form or by any means, or for any
purpose, without the express written permission of Datalogic S.p.A. and/or its
affiliates • Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S. and the E.U.
See the Safety & Regulatory Addendum included with your product for additional
regulatory, safety and legal information.
www.datalogic.com
BSR idware GmbH
Jakob-Haringer-Str.3
A-5020 Salzburg
https://www.bsr.at
sales@bsr.at
Documents / Resources
|
DATALOGIC A22 Mobile Computer
Scanner
[pdf] User Guide
A22, A22 Mobile Computer Scanner, Mobile Computer Scanner, Computer Scanner,
Scanner
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>