Einhell TP-AG 18 125 CE Q Li – Solo Power X Change Professional Cordless Angle Grinder Installation Guide

Einhell TP-AG 18 125 CE Q Li – Solo Power X Change Professional Cordless

Angle Grinder

Product Information:

Product Name: TP-AG 18/125 CE Q Li

Product Type: Cordless Angle Grinder

Model Number: Art.-Nr.: 44.311.55

Product Manual Number: I.-Nr.: 21012

Language: English

Product Usage Instructions

1. Safety Instructions:
   • Before using the product, read and follow all safety instructions provided in the user manual.
   • Ensure that all packaging and transport safety measures are removed before operating the angle grinder.
   • Use appropriate personal protective equipment, such as safety goggles and gloves, while using the angle grinder.
   • Keep the angle grinder out of the reach of children and unauthorized persons.
2. Technical Specifications:
   • Sound pressure level (LpA): 85.86 dB(A)
   • Sound power level (LWA): 93.86 dB(A)
   • Vibration emission value (hand grip): ahAG = 8.612 m/s2
   • Vibration emission value (additional handle): ahAG = 10.94 m/s2
3. Before Operation:
   • Mount the additional handle before operating the angle grinder.
   • Tighten the handle securely in either the left or right position.
   • Ensure that the protective device is properly installed and securely in place.
4. Operation:
   • To charge the Li-ion battery pack, remove it from the handle and follow the instructions in Figure 1a-1b.
   • To change and adjust the protective device, refer to Figure 3for instructions.
   • When using the angle grinder, ensure that the grinding discs are securely fastened using the lock nut and quick-release nut.
5. Battery Status:
   • The battery status is indicated by the LED lights on the speed display:
   • 1 LED: 3000 min-1
   • 2 LED’s: 4500 min-1
   • 3 LED’s: 6500 min-1
   • 4 LED’s: 8500 min-1
   • 5 LED’s: 10,500 min-1
   • All 3 LEDs are lit: The battery is fully charged.
   • 1 LED is blinking: The battery is empty, recharge the battery.
6. Changing Grinding Discs:
   • To change the grinding discs, follow the instructions provided in Figure 5. Make sure to lock the spindle and use the disc retaining and quick-release nut.

Original operating instructions Cordless Angle Grinder

Danger!
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Explanation of the symbols used (see Fig. 11)

1. Danger! – Read the operating instructions to reduce the risk of injury.

2.  Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.

3. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials.
   Never use the device to work on any materials containing asbestos!

4.  Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.

5. This safety guard is designed for sanding/ grinding.

6. This safety guard is designed for cutting and grinding/sanding. (it is not included in delivery)

7. Always operate with two hands..

Safety regulations

The corresponding safety information can be found in the enclosed booklet.
WARNING!
Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

Layout and items supplied

2.1 Layout (Fig. 1)

1. Spindle lock
2. ON/OFF switch
3. Additional handle
4. Guard
5. Quick-clamp nut
6. Speed controller
7. LED speed display
8. Overload display
9. Removable dust guard

Items supplied
Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.

• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suffocating!

• Angle grinder
• Additional handle
• Quick-clamp nut
• Original operating instructions
• Safety instructions

Proper use

The angle grinder is designed for grinding metal and stone when using the appropriate grinding wheel and guard.
Warning! To cut metal and stone the grinder/sander may only be used when the guard (available as an accessory) is mounted. The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Technical data

Motor power supply: …………………………. 18 V DC
Rated speed: ……………………….3000-10500 min-1
Max. wheel diameter: ……………………….. 125 mm
Grinding wheels: …………………. 125 x 22 x 6 mm
Cutting wheel: …………………….. 125 x 22 x 3 mm
Mounting spindle thread: ……………………….. M14
Weight: ……………………………………………..1.75 kg
Danger!
Sound and vibration
Sound and vibration values were measured in accordance with EN 62841.
LpA sound pressure level ………………. 85.86 dB(A)
KpA uncertainty ………………………………………3 dB
LWA sound power level ………………… 93.86 dB(A)
KWA uncertainty ………………………………………3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing. Total vibration values (vector sum of three directions) determined in accordance with EN 62841.
Handle
Vibration emission value ah = 8.612 m/s2 K uncertainty = 1.5 m/s2

Additional handle
Vibration emission value ahAG = 10.94 m/s2
K uncertainty = 1.5 m/s2
The specified vibration value was established in accordance with a standardized testing method.
It may change according to how the electric equipment is used and may exceed the specifi ed value in exceptional circumstances.
The specified vibration value can be used to compare the equipment with other electric power tools. The specifi ed vibration value can be used for initial assessment of a harmful eff etc.
Warning:
The vibration and noise emission levels may vary from the level specified during actual use, depending on the way in which the power tool is used, especially the type of workpiece it is used for.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances that are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.

Caution!
Residual risks
Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Before starting the equipment

Warning!
Always remove the battery pack before making adjustments to the equipment.
5.1 Fitting the additional handle (Fig. 2)

• The angle grinder must not be used without the additional handle (3).
• The additional handle can be secured in any of two positions (A, B).

Replacing and adjusting the guard (Fig. 3) Replacing:

• Remove the quick-clamp nut (5) and the clamping flange underneath.
• Open the clamp lever (f) on the guard (4).
• Turn the guard (4) through 180° in a clockwise direction so that the guard points upwards.
• Remove the guard (4).

To mount, proceed in the reverse order.

Adjusting:

• Adjust the guard (4) to protect your hands so that the material being ground is directed away from your body.
• The position of the guard (4) can be adjusted to any specific working conditions. Undo the clamp handle (f) and turn the cover (4) into the required position.
• Ensure that the guard (4) correctly covers the gear wheel casing.
• Secure the clamp handle (f) again.
• Ensure that the guard (4) is secure.

Warning!
Make sure that the guard is perfectly secure.
Warning!
Never use the angle grinder without the guard.

Operation

Charging the Li battery pack (Fig. 1a-1b)

1. Remove the battery pack (a) from the handle, pressing the push lock button (b) downwards to do so.
2. Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (c) into the main socket outlet. The green LED will then begin to flash.
3. Push the battery pack onto the battery charger.

In section 10 (Charger indicator) you will fi nd a table with an explanation of the LED indicator on the charger.
If the battery pack fails to charge, check for the
following:

•  voltage at the power socket

• whether there is good contact at the charging contacts of the charging unit
  If the battery pack still fails to charge, send

• the charger and charging adapter

•  and the battery pack to our customer service center.

and delivered when you send them to us, please contact our customer service or the point of sale at which the equipment was purchased. When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and fires.

To ensure that the battery pack provides long service, you should take care to recharge it promptly. You must recharge the battery pack when you notice that the performance of the device drops. Never allow the battery pack to become fully discharged. This will cause it to develop a defect.
Switching on (Fig. 4) To start the equipment, push the On/Off switch (2) forward and press it down. To switch off the angle grinder, depress the On/Off switch (2) at the back. The On/Off switch (2) will jump back into its starting position.
Important!
The equipment switches to “Standby Mode” after 10 minutes of non-use.
To reactivate: Switch on the equipment twice or press the battery capacity indicator.
“Standby Mode” protects the battery|
Important!
Following a stoppage (due to overloading), the cordless equipment starts up again automatically
Important!
Wait until the machine has reached its top speed. You can then position the angle grinder on the workpiece and machine it.
Speed controller (Fig. 1c/Item 6)

You can preselect the speed by turning the speed controller (6).
The most suitable speed depends on the type of application and the maximum rated speed of the grinding/sanding tool. Use the speed controller (6) to select a speed in the range from 3,000 to 10,500 min-1.
You can choose from 5 speed settings.
These are indicated by the LEDs on the speed display:

• 1 LED: 3000 min-1
• 2 LEDs: 4500 min-1
• 3 LEDs: 6500 min-1
• 4 LEDs: 8,500 min-1
• 5 LEDs: 10,500 min-1

Plus direction: Higher speed
Minus direction: Lower speed

Wait until the tool has reached its top speed. You can then position the angle grinder on the workpiece and machine it.
Constant electronics
This tool is equipped with constant electronics. Constant electronics keeps the set speed constant even when the tool is working under load.

Overload display (Fig. 1c/Item 8)
The constant electronics function keeps the speed constant even when the load increases. If the load rises too high for the tool, this will be signaled by fl ashing of the overload display (8).

The following cases will be signaled by the overload
display (8):

• Exceeding the maximum power current permitted for the motor. The overload display (8) will go off again when the load is reduced or it will flash for a short time after the tool has been switched off in order to protect the motor from the overload.
• Exceeding the maximum temperature permitted for the motor. The overload display (8) will flash for a short time and will then go off again. Allow the tool to cool down before you continue to use it.

Battery capacity indicator (Fig. 1d/Item c)
Press the battery capacity indicator switch (e). The battery capacity indicator (d) shows the charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the battery from the equipment, keep it at room temperature for one day. If the fault reoccurs, this means that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment. Never use or charge a defective battery.

Changing the grinding wheels (Fig. 5)

• The wheel is easy to change using the spindle lock and quick-clamp nut.
• Press the spindle lock and allow the grinding wheel to engage.
• Undo the quick-clamp nut by turning it counterclockwise by hand (see Fig. 5).
• Change the grinding wheel or cutting wheel and tighten the quick-clamp nut by turning it clockwise by hand.

Warning!
For safety reasons the quick-clamp nut (5) may only be used for this angle grinder.
Notice!
Only ever press the spindle lock when the motor and grinding spindle are at a stand-still! You must keep the spindle lock pressed while you change the wheel!

Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at least 1 minute with the grinding or cutting wheel fitted in place. The vibrating wheels are to be replaced immediately.

Grinding Wheels .

• Never use a grinding or cutting wheel bigger than the specified diameter.
• Before using a grinding or cutting wheel, check its rated speed.
• The maximum speed of the grinding or cutting wheel used must be higher than the idle speed of the angle grinder.
• Use only grinding and cutting wheels that are approved for a minimum speed of 10,500 rpm and a peripheral speed of 69 m/sec.
• Check the direction of rotation when you use diamond cutting wheels. The directional arrow on the diamond cutting wheel must point in the direction in which the tool rotates.

Warning!
Operating Modes
Rough grinding (Fig.6) Caution: Use the safety device for sanding/
grinding
For the best rough grinding results, hold the grinding
wheel at an angle of between 30° and 40° to
the workpiece surface and guide back and forth
over the workpiece in steady movements.
Cutting (Fig. 7)
Caution: Use the safety device for abrasive cutting (Available as an accessory, see 7.3).
When you use the right-angle grinder for cutting purposes, avoid tilting it in the cutting plane. The cutting wheel must have a clean cutting edge. A diamond cutting wheel is best used to cut hard stone.

Warning!
It is prohibited to use the machine on asbestos materials!
Warning!
Never use a cutting wheel for rough grinding.
Note:
To increase the power and running time of the cordless equipment, we recommend using our 4.0 Ah Power X-Change.
Art. No.: 45.113.96

Important!
To increase the cutting performance and running time of the cordless equipment, we recommend that you use a cutting wheel with a thickness of 1 mm.

Motor
It is vital for the motor to be well-ventilated during operation. Be sure, therefore, to keep the ventilation holes clean at all times.
Removable dust guard (Fig. 8-10/Item 9)
The cordless angle grinder is equipped with a removable dust guard in order to protect the motor from too high a dust load. For cleaning purposes, take off the removable dust guard (9) as shown in Fig. 8, clean it with compressed air, and refi t it on the tool as shown in Fig. 10.

Cleaning, maintenance and ordering of spare parts

Danger!
Always pull out the battery pack before starting any cleaning work.
Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

Maintenance
There are no parts inside the equipment which require additional maintenance.

Ordering replacement parts
Please quote the following data when ordering
replacement parts:

• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required For our latest prices and information please go to  www.Einhell-Service.com
• Safety guard for cutting (Art. No.: 44.500.59)

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offi ces.

Storage

Store the equipment and accessories in a dark and dry place at above-freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging

For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations.
This does not apply to any accessories or aids without electrical components supplied with the old equipment.
Please note that batteries and lamps (e.g. lightbulbs) must be removed from the tool before it is disposed of.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of Einhell Germany AG.
Subject to technical changes

Charger indicator

Das Ladegerät ist an das Netz angeschlossen und betriebsbereit, Akku ist nicht im Ladegerät

An| Aus| Laden

Das Ladegerät lädt den Akku im Schnellladebetrieb.

Die entsprechenden Ladezeiten finden Sie direkt am Ladegerät. Hinweis! Je nach vorhandener Akkuladung können die tatsächlichen Ladezeiten von den angegebenen Ladezeiten etwas abweichen.

Aus| An| Der Akku ist aufgeladen und einsatzbereit. (READY TO GO) Danach wird bis zur vollständigen Ladung auf eine Schonladung um- geschaltet.

Lassen Sie hierzu den Akku etwa 15 min. länger am Ladegerät.

Maßnahme:

Entnehmen Sie den Akku aus dem Ladegerät. Trennen Sie das Lade- gerät vom Netz.

Blinkt| Aus| Anpassungsladung

Das Ladegerät befindet sich im Modus für schonende Ladung. Hierbei wird der Akku aus Sicherheitsgründen langsamer geladen und benötigt mehr Zeit. Dies kann folgende Ursachen haben:

–   Akku wurde sehr lange Zeit nicht mehr geladen.

–   Die Akkutemperatur liegt nicht im Idealbereich zwischen 10° C und 45° C.

Maßnahme:

Warten Sie bis der Ladevorgang abgeschlossen ist, der Akku kann trotzdem weiter geladen werden.

Blinkt| Blinkt| Fehler

Ladevorgang ist nicht mehr möglich. Der Akku ist defekt.

Maßnahme:

Ein defekter Akku darf nicht mehr geladen werden. Entnehmen Sie den Akku aus dem Ladegerät.

An| An| Temperaturstörung

Der Akku ist zu heiß (z. B. direkte Sonnenbestrahlung) oder zu kalt (unter 0° C)

Maßnahme:

Entnehmen Sie den Akku und bewahren Sie diesen 1 Tag bei Raumtemperatur (ca. 20° C) auf.

Service information
We have competent service partners in all countries named on the guarantee certifi cate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

• Not necessarily included in the scope of delivery!
  In the eff ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com.
  Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

• Did the equipment work at all or was it defective from the beginning?

• Did you notice anything (symptom or defect) prior to the failure?

• What malfunction does the equipment have in your opinion (main symptom)? Describe this malfunction.

Warranty certificate

Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.
2. The warranty services cover only defects due to material or manufacturing faults on a product that you have bought from the manufacturer mentioned below and are limited to either the rectification of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee: – Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance. – Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it). – Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fi tted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fi tted. This also applies if an on-site service is used.
5. To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com.
   Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identification will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.Of course, we are also happy off er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units that are no longer covered. To take advantage of this service, please send the device to our service address. Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.

References

• Einhell Service
• Einhell Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>