Leviton 41089-6EP QuickPort Surface Mount Housing User Manual

Leviton 41089-6EP QuickPort Surface Mount Housing

Instructions for Use

IMPORTANT INSTRUCTIONS

1. Read and understand all instructions. Follow all warnings and instructions marked on the product.
2. Do not use this product near water e. g., near a tub, wash basin, kitchen sink, laundry tub, a wet basement, or swimming pool.
3. Never push objects of any kind into this product through openings, as they may touch dangerous voltages.
4. SAVE THESE INSTRUCTIONS.

SAFET Y INFORMATION

1. Never install communications wiring or components during a lightning storm.
2. Never install communications components in wet locations unless the components are designed specifically for use in wet locations.
3. Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface.
4. Use caution when installing or modifying communications wiring or components.

DESCRIPTION

Leviton’s QuickPort Surface Mount Housings are field-configurable for most QuickPort Snap-in connectors and adapters. The housing features port identification windows, and the ability to snap an optional security screw to prevent removal of the cover. (Screw not included)

INSTALLATION

1. Noting the port side and the cable entry side of the base, use double back tape, self-adhesive hook, and loop strips, or the 1˝ screws provided to mount the base to the wall.
2. Terminate the wire onto the QuickPort snap-in adapter or connector per that product’s instructions.
3. Insert the connector into the housing at a steep angle, rotate, and push the connector into the base. (Figure 1)
4. Swing the back part of the jack down and forward until it fully locks behind the retention ledge on the base.

Removing the jack

• Place a small flat screwdriver in the retention ledge slot on the base. Pry upward to release.

FEATURES

• Connectivity with a QuickPort Snap-in Snap:
  The enclosure is designed to accommodate Leviton’s QuickPort snap-on connectors, which makes it possible to install data, voice, audio, and video connections in a manner that is both straightforward and adaptable.

• Mounting on the surface:
  The housing has been designed for applications that need surface mounting, meaning that it may be readily put on walls or other flat surfaces, giving the illusion of being clean and orderly.

• Versatility:
  As a result of the housing’s ability to house a variety of QuickPort connectors—including RJ45 Ethernet jacks, HDMI connectors, USB ports, audio connectors, and many more—a comprehensive selection of connectivity options is made available.

• Construction that is Rugged:
  In most cases, the housing is made out of durable materials in order to provide a long-lasting function and provide adequate protection for the connectors that have been fitted.

• Multiple Ingress Points:
  The typically has numerous ports, which gives you the ability to personalize the connectivity solution based on the requirements of your particular situation.

• Variations in Color:
  It is common practice for Leviton to offer a variety of color options for their surface mount housings. This gives you the ability to coordinate the housing with the color scheme of your room or your network.

• Simple and quick assembly:
  It is common practice for the housing to come with pre-drilled mounting holes and mounting hardware, making the assembly of the housing quite uncomplicated.

It is important to keep in mind that the features and specifications of a product may be modified over time. Because of this, I suggest that you check the Leviton website or contact their support in order to obtain the most recent information regarding the Leviton QuickPort Surface Mount Housing.

PRECAUTIONS

Take into consideration the following typical safety measures:

• Security in Electrical Systems:
  In order to prevent injuries caused by electrical shocks or mishaps, be sure that the power is turned off and disconnected before installing or handling any electrical components.

• Compatibility:
  Make sure that the connectors and modules that will be used with the housing are compatible with the QuickPort system and are appropriate for the applications that will be using the housing.

• Correct Installation:

• Be sure to mount the surface mount housing correctly by carefully following the directions provided by the manufacturer. Make sure it is affixed to the wall or surface in a way that is both secure and safe.

• Administration of Cables:

• To prevent interference, signal deterioration, or unintentional disconnections, you should take special care to manage and organize the wires in the housing in an appropriate manner.

• Considerations Regarding the Environment:
  Make sure that the housing is installed in an appropriate location, one that is free from extreme heat, moisture, and any other factors that could potentially be harmful.

• Roughness and Garbage:
  It is important to ensure that the housing and the connectors are clean and clear of any dirt, debris, or other pollutants that may have an effect on the performance of the connections.

• Take care not to overload:
  If you overload the housing with connectors over its specified capacity, you run the risk of compromising the installation’s ability to work as intended and its level of safety.

• Use Correctly:
  Make use of the surface mount housing for the purpose it was designed for and within the parameters of the operating conditions it specifies.

• Installation Done by Professionals:
  If you do not have experience with electrical installations or network configurations, it is recommended that you seek the assistance of a professional for the installation and configuration of the system.

• Ongoing Quality Control:
  It is important to perform routine checks on the surface mount housing as well as the connectors to ensure that they are in good shape and operating correctly.

Always refer to the product’s user manual or paperwork if you need particular precautions and instructions pertaining to the Leviton QuickPort Surface Mount Housing. If you follow the guidelines given by the manufacturer, you will help ensure a secure and dependable installation.

Leviton and Leviton Block & Design are trademarks of Leviton Manufacturing Co., Inc. and are registered trademarks in many countries throughout the world.

© 2012 Leviton Manufacturing Co., Inc.

• Customer Support:  800.824.3005
• International:  +1.425.486.2222
• Web:  www.leviton.com

FREQUENTLY ASKED QUESTIONS

What is the Leviton 41089-6EP QuickPort Surface Mount Housing?

The Leviton 41089-6EP is a QuickPort surface mount housing designed to accommodate various QuickPort snap-in modules for easy customization of connectivity solutions.

What are the dimensions of the surface mount housing?

The exact dimensions may vary, but typically it is around 4.5 inches in height, 2.75 inches in width, and 1.25 inches in depth.

What type of material is the housing made of?

The Leviton 41089-6EP housing is typically made of durable plastic material.

What is the color of the surface mount housing?

The housing is usually available in white color.

How many QuickPort snap-in module ports does the housing have?

The Leviton 41089-6EP housing typically has six QuickPort snap-in module ports.

What types of modules can be installed in the housing?

The housing is compatible with various Leviton QuickPort snap-in modules, including Ethernet, audio, video, and other data connections.

Is the housing suitable for indoor or outdoor use?

The Leviton 41089-6EP is designed for indoor use, as it may not be weather- resistant for outdoor installations.

Can the surface mount housing be painted to match the wall color?

Yes, the plastic surface mount housing can be painted with appropriate paint to match the wall color if desired.

Does the housing come with mounting screws and hardware?

Yes, the Leviton 41089-6EP housing typically comes with the necessary mounting screws and hardware for easy installation.

Can this housing be used with other Leviton products or systems?

The Leviton 41089-6EP is part of the Leviton QuickPort system, and it can be used with other QuickPort products to create a customized connectivity solution.

Is this housing compatible with shielded modules for additional protection against interference?

Yes, the housing is compatible with both shielded and unshielded QuickPort modules.

What is the maximum number of cables that can be terminated in the housing?

The number of cables that can be terminated in the housing depends on the specific QuickPort modules used and their configuration.

Can this housing be used for both residential and commercial installations?

Yes, the Leviton 41089-6EP housing is suitable for both residential and commercial applications.

Is the housing compatible with angled or keystone modules?

The Leviton 41089-6EP QuickPort housing is designed for QuickPort snap-in modules and may not be compatible with angled or keystone modules.

Can the housing be mounted on any type of wall surface?

The housing can be mounted on most flat surfaces, such as drywall, wood, or plaster.

Download the PDF Link:Leviton 41089-6EP QuickPort Surface Mount Housing User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>