HIDE Skimmer Box Cover Instruction Manual

HIDE Skimmer Box Cover

IN THE KIT

A: HIDE SAFETY KEY
DO NOT LEAVE IN THE COVER! Pass to the Homeowner.
Enables the installed HIDE cover to be safely opened/closed.

B: HEIGHT ADJUSTER
Provides 5mm (3/16”) extra height if inlay material is not thick enough to achieve a flush finish with the top of the Inlay Cover.

C: INLAY COVER
A tray which holds the inlay material e.g. tile, paver, decking, cement.

D: EDGE PROTECTOR
A frame inserted into a recess within the  landscaped area. It protects the coping/surrounds from chipping/breakage.

E: ADHESIVE
HIDE Adhesive to be inserted into a caulking gun. For use when assembling the Inlay Cover.

F: INFO PACK
Homeowners Manual and Warranty pack. To be passed on after installation.

EQUIPMENT YOU’LL NEED
(The type of inlay materials to be fitted will determine the tools required.)

INLAY SOLUTIONS

Depending on where the HIDE product is to be installed, it may run across two different types of landscaping materials. Similarly, it may need to be inserted where grout lines are present, or fitted with an intricate tile pattern.
With a little extra care, the HIDE product can be installed so it is virtually invisible.

1. GROUT MATCHED
2. TILE BANDING
3. INTRICATE PATTERNS
4. TIMBER DECKING

ASSEMBLING THE INLAY COVER

NOTE NUMBER OF KEYWAYS REQUIRED: 10, 20 & 30mm (0.4”, 0.8”, & 1.2”) lids require one keyway cut and 40, 50 & 60mm

1. CUT TILE (INLAY) TO SIZE
   If using tumbled/chiselled edge tile/stone cut all 4 edges for a better finish. See previous page to view options for aligning inlay and grout lines to coping/surrounds.

2. MARK UP & CUT KEYWAY AT  CENTER
   Ensure keyway is positioned on the tile edge which will be closest to the pool. Check that the key fits the keyway before gluing.
   NOTE : Two key models require two keyways.

3. CLEAN & DRY
   Failure to complete these steps may result in a weak adhesive bond.
   You must insure that bonding materials are fully dry before bonding especially in cold weather.

4. CALCULATE THE AMOUNT OF ADHESIVE REQUIRED by measuring the height difference between Inlay Cover and Inlay material thickness.

5. HEIGHT DIFFERENCE UNDER 3MM (1/8”)
   1 – 2mm (1/16”) = Qty 5 x beads 5mm (3/16”) wide or 2 – 3mm (1/8”) = Qty 7 x beads 8mm (5/16”) wide

6. Flip Inlay Cover C over and press down onto inlay (tile):
   So that both inlay cover and tile sit upside down flush on a flat surface for 15 minutes to let adhesive stiffen.
   Curing time is longer in cold weather.

7. HEIGHT DIFFERENCE OVER 3MM: (1/8”)
   USE THE HEIGHT ADJUSTER SUPPLIED

8. HEIGHT DIFFERENCE OVER 3MM: (1/8”)
   To calculate TOTAL adhesive to use with the Height Adjuster, remember there will be two lots of adhesive applied ie. adhesive is applied inside the Inlay Cover (C) AND the reverse side of the inlay material (tile).

9. Place Height Adjuster on inlay (tile), then flip Inlay Cover (C) over and press down onto Height Adjuster (B):

10. PRESS DOWN FOR A LEVEL FINISH

11. WAIT WHILE ADHESIVE STIFFENS
    Curing time is longer in cold weather.

12. CENTER TILE IN THE COVER

13. LET ADHESIVE SET
    Curing time is longer in cold weather.

14. TO FIT DECKING BOARDS
    Apply glue between timber and lid allowing for sufficient clearance for drainage.
    For a seamless finish, pattern match timber and grain through the inlay cover.

15. POOL PREPARATION
    NEW POOLS: SET DEPTH – WHEN LAYING LEVELLING BED, PROVIDE SPACE FOR EDGE PROTECTOR SO IT WILL BE FLUSH WITH TOP OF INSTALLED TILE
    EXISTING POOLS: CUTOUT – MARK OUTLINE FOR CUTTING SURROUNDS AND CUT DEPTH TO MATCH SELECTED EDGE PROTECTOR AND A MORTAR BED

16. INSTALL MORTAR
    REMOVE DEBRIS FROM RECESS THEN FILL RECESS WITH A MORTAR BED

17. PUSH IN EDGE PROTECTOR

18. ALLOW MORTAR TO SET

19. EDGE PROTECTOR
    The Edge Protector may be left loose on its mortar bed or filled with an expansion joint gap filler.

IMPORTANT CONTRACTOR INFORMATION

EARTHING (BONDING) RULES AND REGULATIONS
HIDE products are constructed from 316 marine grade stainless steel, and are considered a conductive material. Safety regulations vary and you should consult your local authority to determine what rules may apply in your area.
Bonding is the responsibility of the installer, attachment points have been provided to allow for use of bonding devices if required. Check your local regulations to ensure the installation meets electrical safety requirements.

SAFETY FIRST

• REMOVE KEY FROM COVER
  NEVER leave the HIDE Safety Key in the cover for any reason, especially after install.
  Leaving the Safety Key in the top of an installed cover may be dangerous, as it enables children to access the Skimmer.

• PASS KEY TO HOMEOWNER
  DO NOT RISK IT – HIDE recommends that once the cover is installed, the Safety Key is passed to the homeowner and is stored securely.

• NO ACID / CHEMICAL WASH CONTACT
  ACID and chemical washes will cause discolouration and/or rusting on the stainless steel HIDE components. Acid or chemical contact will void the HIDE warranty.

• SAFE WORK PRACTICES
  ALWAYS be conscious of your and co-workers’ safety while assembling and installing the HIDE components.
  Personal protective equipment (PPE) must be worn, especially when cutting tiles and using adhesive.
  Recommended PPE includes eye and ear protection, gloves, dust mask and safety boots.

OTHER PRODUCTS

ACCESS & INSPECTION
The HIDE Access and Inspection Covers can be used for underground service points including: water table inspection pipe (typically close to the skimmer box); grey water inspections outlets (IO); water tanks; balance tanks; taps and irrigation; valves and meters.

DRAIN
The HIDE Drain Cover can be used in most outdoor areas, including patios, decks and pathways allowing for a water intake compatible with a standard 90mm or 100mm drainage network.
HIDE Drain Covers not only look amazing but provide superior safety and performance.

CONCRETE WET POUR
The HIDE Concrete Cover is filled and finished at the same time as the pool surrounds. This ensures this cover perfectly matches the selected surface finish in both texture and colour. If you are wanting to finish your pool surrounds in a material like polished or decorative concrete, this is the product for you!

International Patent Protection:
The skimmer box cover – lid and key product contained herein is covered by U.S. Patent Application. No. 15/336,801 The skimmer box cover – lid product contained herein is covered by U.S. Design Patent No. D819788

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>