COSTWAY JV10229 Electric Height Adjustable Standing Desk User Manual
- June 4, 2024
- COSTWAY
Table of Contents
JV10229 Electric Height
Adjustable Standing Desk
User Manual
JV10229 Electric Height Adjustable Standing Desk
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ
AND KEEP IT FOR FUTURE REFERENCE.
Please give us a chance to make it right and do better!
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP!
Follow Costway
Contact Us!
Do NOT return this item.
Contact our friendly customer service department for help first.
US:
cs.us@costway.com
UK: cs.uk@costway.com
Before You Start
Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
recommend that, where possible, all items are assembled near the area in
which they will be placed in use, to avoid moving the product unnecessarily
once assembled.
Always place the product on a flat, steady, and stable surface.
****Keep all small parts and packaging materials for this product away from
babies and children as they potentially pose a serious choking hazard.
WARNING
CAUTION : DO NOT IMMERSE IN WATER READ INSTRUCTIONS BEFORE USING MADE IN CHINA
**WARNING :
PLEASE MAKE SURE YOUR FINGERS ARE VISIBLE AT THE PINCH POINT.
** Make sure that the lifting table is blocked without obstacles during the
lifting process. The tabletop should not be close to the wall. The length of
the line is long enough for the table to move up and down.
Please ensure that children do not touch the electric lifting table,
away from the risk of injury and electric shock.
Please make sure that all electronic parts do not come into contact with
liquids.
Do not sit or stand on the table frame, crawl or lie under the table
frame.
Do not place any objects over 2Ocm( 7.87″) in height under the table.
Do not disassemble any parts without authorization to keep away from the
risk of electric shock.
Please ensure that the continuous operation of the lifting time does not
exceed two minutes, so as not to damage the lifting motor.
**** If there is a power failure or the power cord is not plugged in, you
need to refer to the operating instructions to reset.
INSTRUCTIONS FOR USE
This electric lifting table is only suitable for indoor dry environments.
The height of this electric lift table can be adjusted within a certain range,
so it can be applied to most ergonomic scenarios. The risks caused by use in
scenarios other than the above are borne by the user himself. The manufacturer
is not responsible for damages and losses caused by improper operation and
improper handling.
IMPORTANT NOTE
Please read the user manual carefully. Once the table is given to someone
else, please provide the user manual together with the table to them.
parts List
packing list
Installation Guide
It is recommended that you choose an open and flat ground during installation
or use a mat to pave the K. working ground to prevent injury or scratches to
the table and table frame during installation.
STEP 1 : As shown in the figure above, place desktop A1 and desktop B3 on
clean and flat ground, and insert 4PCS dowel 2 into desktop A as shown in the
figure.
STEP 2: Put the left column 8 and the. the right column 13 on clean ground, and place the frame4 as shown in the figure, use a 4mm Allen key 24and 4 PCS M6*25 screws17to fix the column and the frame.
STEP 3: As shown in the figure above, loosen the plastic cover, insert
the transmission rod 9 into the mark of the hexagonal bar 6of the right
column, insert the hexagonal bar into the hole of the left column, use the
open-end wrench 23 to slightly rotate the angle of the hexagonal bar, and
insert it into the transmission rod 9 and the limit piece is tightly attached
to the right column. After adjusting the position, tighten the plastic cover
in the opposite direction to lock it.
STEP 4: As shown in the figure above, hook 7 is stuck in
the notch on the frame, and then side plate 5 is fixed with 4PCS countersunk
screws 19 through a 4mm Allen key 24, and the hook is pressed by the side
plate.
STEP 5: Align the corresponding holes according to the above picture, use
a power tool or a 4mm Allen wrench to tighten and fix it with 10PCS M614
screws 26.
STEP 6: According to
the above picture, the 4 table plate connectors 16 correspond to the holes on
the table board, use a power tool or a 4mm Allen key to lock and fix it with
8PCS M6 14 screws26 STEP 7: According to
the picture above, manually fold the socket rack 10 and the folding drawer11
into the shape shown in the picture.
STEP8: According to the above picture, use M6*14 screwsto
26 to install the socket rack 10, fold the drawer, and use ST4.9 screws 20 to
install the hand controller, and the position of the drawer and hand
controller can be interchanged left and right. After installing the hand
controller, the socket rack, and the drawer folded, use the cord buckle to
organize the power cord and the connecting cord.
STEP 9: According to the picture above, use M10*35 screws 18 to install the feet 12. STEP 10: Place the whole table on the ground as shown in the figure, turn on the power, make sure the table top is flush, and the height of the table on both sides of the column is the same from the ground. There should be no objects higher than 20cm( 7.87″) under the table. Reset it according to the instructions of the controller. Perform lifting and other operations after resetting.
Operation Installation
Note 1 The appearance of the hand controller is subject to the actual
order, and the operation method is common.
Note 2 Please make sure that there are no obstacles when the table is
raised and lowered, the tabletop is not close to the wall, and the length of
all lines is sufficient for the table to move up and down.
suggestion The most comfortable height when you sit down is preset to 1,
the most comfortable height when standing up is preset to 2, and the other
preset height can be freely set to other heights.
Reset exception protection
Phenomenon
After the controller abnormally reports an error, the digital tube displays
E07-E09. Even if the power is turned off and then turned on, the error display
will still be maintained, and pressing any key will not work. Operating
After long pressing the down button for 5 seconds, the digital tube displays
RST, releases the button, and then presses the down button to reset.
Set upper limit
Press the “M” button, and the digital tube displays “S-“, and release the
button. Long press the up button, and the digital tube flashes once, release
the button. Press the “M” button again and hold it for 2 seconds, the digital
tube displays “999”. Complete the upper limit setting.
Set lower limit
In the reset state, the digital tube displays the state of RST. Long press the
down button, and the digital tube flashes once, release the button. Press the
“M” key again for 2 seconds, the digital tube displays “000”. Complete the
lower limit setting. Cancel the limit
Press the “M” button, and the digital tube displays “S-“, and release the
button. Press the “M” button again and hold it for 2 seconds, the digital tube
displays “555”. Delete the upper and lower limit settings. Locking
Press the “M” button, the digital tube displays “S-“, after long pressing the
“M” button for 5 seconds, the digital tube jumps back to the digital display,
continue to hold the “M” button for 3 seconds, the digital tube displays LOC,
and the hand control buttons are locked. Unlock
In the LOC locked state, long press the “M” button for 8 seconds, the digital
tube displays the number, and the hand control buttons are unlocked.
Minimum height value modification
In the reset state, the digital tube displays the state of RST. Long press the
button “M” for 5 seconds, the digital tube will display the height value after
reset, and it will flash on and off. Press the up key or down key to adjust to
the desired height value. After releasing the button for 5 seconds, the
digital tube jumps back to RST, and the modification is successful.
Memory Jogging and continuous switching
In the reset state, the digital tube displays the state of RST. Long press the
button “I” for 5 seconds to switch between memory jog and memory continuation.
The digital tube displays “10. 1”, and the memory position continues to move.
The digital tube displays “10.2”, and the memory position is inching. ****
CM//NCH display switch
In the reset state, the digital tube displays the state of RST. , Long press
button “2” for 5 seconds to switch between inch display and cm display. The
digital tube displays “10.3”, and the height value cm is displayed after
resetting. The digital tube displays “10.4”, and the height value is displayed
in inches after reset. Reverse sensitivity selection when encountering
resistance
In the reset state, the digital tube displays the state of RST. After pressing
the up button for 5 seconds, you can change reverse sensitivity when
encountering resistance, and the digital tube will switch display, (currently
displayed as a level).”10.5″–10kg (22 Ibs)
“10.6”–15kg (33 Ibs)
“10.7”–20kg (44 Ibs)
Memory location setting
Press the “M” key, and the digital tube displays “S-“, select and press one of
the memory keys (number keys), and the current position will be memorized. Use
the up/down keys to raise the desk to the position you want and repeat the
above actions.
Common problems and solutions
-
1f your table has the following problems, please try to reset it to solve them.
• Abnormal work
• The hand control panel displays RES (reset).
• The hand control board displays an error message (E07, E08), but the motor drive line is connected normally. -
If the hand control panel displays HOT (H 01), please disconnect the power and cool down for 20 minutes.
Welcome to visit our website and purchase our quality products!
With your inspiring rating, COSTWAY will be more consistent to offer you EASY
SHOPPING EXPERIENCE, GOOD PRODUCTS, and EFFICIENT SERVICE! US office: Fontana,
California
UK office: Ipswich
- Reward Points
- Exclusive Customer Service
- Personalized Recommendations
- Permanent Shopping Cart
- Order History
5 Star Rating ***
**
We would like to extend our heartfelt thanks to all of our customers for taking the time to assemble this product and giving us valuable feedback.
http://www.costway.com/hysalesrule/qr
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>