Z8/Z8MS/Z8TG
ATX MID-TOWER
COMPUTER CASE
User’s Manual

• To ensure safe and easy installation, please read the following precaution.
• Product design and specifications may be revised to improve quality and performance without notice.
  Ver. 041120

Precautions

• Read this manual carefully before installing.
• Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
• Wear gloves to prevent accidents when installing the product.
• Severe damage may occur when mounting the system, so do not apply excessive force.
• Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
• Be careful not to block the ventilation hole of the product when using the system.
• Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
• Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
• Do not insert your hand or another object into the product during operation, as this may injure your hand or damage the object.
• Store and use the product out of children’s reach.
• Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
• The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Fan Support

| Top| 2ⅹ120mm / 2ⅹ140mm
Front| 3ⅹ120mm / 3ⅹ140mm
Rear| 1 x 120mm
Bottom| 2 x 120mm (Remove SSD Brackets)
Fan(s) Included| Front| 3 x 120mm| Addressable RGB 3 x 120mm
Rear| 1ⅹ120mm
| ARGB Controller Included
Radiator Support| Top| 120mm / 240mm / 280mm
Front| 120mm
Rear| 120mm
I/O Ports| 2ⅹUSB3.0, 1ⅹUSB2.0, 1ⅹHeadphone Jack, 1ⅹMicrophone jack, Power Button, Reset Button, LED Button

Accessories

I/O Ports

| Part

---|---
ⓐ| Power Button
ⓑ| HDD / Power LED
ⓒ| Headphone Jack
ⓓ| Microphone Jack
ⓔ| USB 2.0 Port
ⓕ| USB 3.0 Ports
ⓖ| Reset Button
ⓗ| LED Button

1. Removing the side panels
   1) Tempered Glass

2. Steel Panel

2. Removing the front panel

3. Mounting the motherboard
   3-1. Motherboard size
   

4. Mounting the PCI-E(VGA) Card
   

5. Mounting the 2.5” SSD
   

6. Mounting the 3.5″ HDD
   ※ Z8 MS, Z8 TG Only
   ※ How to control RGB LED
   – LED colors & patterns can be changed by pressing the LED Button on I/O ports.
   – Long pressing on the LED Button for 6 seconds, RGB LED will be turned off after blinking twice in white.
   – Long pressing on the LED Button for 3 seconds, RGB will be synchronized with the motherboard after blinking once in white.
   Press the LED Button again to desynchronize with the motherboard.
   A. ARGB LED 1~4 / 3-Pin
   B. ARGB LED Control Button / 2-Pin
   – Connector to ARGB LED Control Button
   C. Other Motherboards Sync / 3-Pin
   – Connector to Motherboard
   – Requires Motherboard that Supports RGB Sync
   ※ Caution: if Addressable 3 Pin connects to a 12V header instead of a 5V header improperly, It may cause fatal damages to the product by the overvoltage.
   D. SATA Power / 15-Pin
   – Connector to PSU
   – Input: 5V
   E. Connect the ARGB connector to the RGB hub

7. Mounting the PSU
   

8. Mounting the radiator

9. Mounting the top radiator
   ・120mm
   ・240mm
   ・280mm

10. Mounting the front and rear radiator
    ・120mm
    

11. Fans Included / Specifications

12. Mounting the fans

13. Mounting the top & bottom fans
    ・2 x 120mm
    ・2 x 140mm

14. Mounting the rear fan
    ・1 x 120mm

15. Mounting the front fans
    ・3 x 120mm
    ・3 x 140mm
    

16.  I/O Connectors

www.zalman.com

References

• zalman.com
• ANDPRO.RU - интернет магазин компьютерной и офисной техники с выгодными ценами и доставкой

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>