MORA MMIX Tronic Basin Mixer Instruction Manual

MORA MMIX Tronic Basin Mixer

Product Information

Product Name: MORA MMIX
Manufacturer: FM
Mattsson Group Certification: PS 1898, CERTIFIERING KONTROLL 1002, SC0052-13

Product Usage Instructions

Flow Control:

• The temperature limiter is adjusted by remeshing the temperature ring (b). Turn it towards the minus symbol to cool the water.

Setting of dishwasher/washing machine valve function:

• For dishwasher supply water, the marked arrow on the rod (c) should point to either Hot or Cold. – Push the handle slightly and turn it to the position that corresponds to the type of water you want supplied to the dishwasher.

Troubleshooting/Service:

• In case of insufficient flow, remove and clean the perlator (d).
• Lubricate the sealing rings (f) with silicone grease

Cleaning:

• Clean the product using mild soap solutions or dishwashing detergents (pH 6-9). Do not spray directly on the product to avoid damaging internal parts. Use a soft cloth.
• Avoid using organic or corrosive cleaners, alcohol-based cleaners, or cleaners with abrasives as they can damage the surface and cause scratches.
• For stubborn lime stains, use cleaning vinegar (not pure vinegar). Avoid contact with aluminum chlorides (e.g., deodorant) as they can discolor the product.

Installation

• It is recommended to consult a certified installation company for installation.
• Flush the pipes before mounting the mixer tap if new plumbing is being installed.
• Ensure that the pipes at the connection point are secured with pipe clamps.
  Note : Disused products can be returned to Mora Armatur for recycling. Please visit the official website of Mora Armatur at [www.moraarmatur.com](http://www.moraarmatur.com) for more information and technical specifications.

TECHNICAL DATA

• Used for tap water.
• Operating pressure, min.: 0.05 MPa (0.5 bar)
• Operating pressure, max: 1 MPa (10 bar)
• Recommended pressure for optimal function: 0.1–0.5 MPa (1–5 bar).
• Test pressure, max: 1.6 MPa (16 bar)
• Max. hot water temperature: 80 °C (recommended: 60 °C).
• Cold water temperature: ˜10 °C.
• Soft PEX® connection tube.

Where there is a risk for frost
If the mixer will be subjected to external temperatures lower than 0 °C (e.g. in an unheated holiday home), the mixer should be disconnected and stored in a heated space.

Cleaning

To clean our products, use a liquid cleaner that is neutral or slightly alkaline (pH 6–9). Do not spray the cleaner directly onto the product, as this could damage the parts inside. Use a soft cloth. Suitable detergents include soap solutions or washing up liquid (not dishwasher detergents). Do not use organic, alcohol-based, corrosive or abrasive cleaners or detergents as they could damage, scratch or dull the surface. To remove stubborn limescale deposits, we recommend household vinegar (not pure spirit vinegar). Avoid contact with aluminium chlorides (e.g. deodorant), which can discolour the product.

INSTALLATION/SETTING

Installation should be carried out by an authorised water and sanitation company. NOTE! When installing new tubes, the tubes must be flushed clean before the mixer is connected. NOTE! Some dripping may occur after use.

• A Install the mixer as shown in the diagram.
• B Connection and clipping

The mixer has a Soft PEX® connection tube. When connecting the mixer, the connection point must be fixed firmly in place with a tube clip as shown in the diagram. No supporting bush is required for Soft PEX® connection tubes with a smooth connection end.

• C Flow control
  Four different flow settings can be selected by turning the flow adjuster (a) 4×90°: 80, 85, 90 and 100 percent of the maximum flow in the system. Turn the chosen lug towards the stop lug. The larger the lug, the weaker the flow will be.

• D Temperature limiter
  The temperature limiter is adjusted by remeshing the temperature ring (b). The further it is turned towards the minus symbol, the cooler the water will be.

• E Setting of dishwasher/washing machine valve function: Cold -> hot water, for dishwasher supply water: The marked arrow on the rod (c) should point to either “Hot” or “Cold”. Push the handle slightly and turn it to the position that corresponds to the type of water you want supplied to the dishwasher.

TROUBLESHOOTING/SERVICE

F Weak water flow. Clogged aerator: Unscrew the aerator (d) and clean the cartridge.
F1–5 The spout or spout attachment point leak when the mixer is turned off:

• Replace the ceramic cartridge (e). First turn off the incoming water supply.
• Perform steps F1–5, using a Mora Armatur servicing tool (MA No. 891096.AE).
  Change the whole ceramic cartridge. If necessary, clean the site where the three gaskets in the ceramic cartridge act as a seal against the mixer body.
  NOTE! Do not scratch the surface. Reassemble in reverse order.

F Changing the sealing rings for the spout:

• Perform steps F1–6, using a Mora Armatur servicing tool (MA No. 891096.AE). Replace the sealing rings (f) and lubricate them.

NOTE! Only use silicone grease.
Disused products can be returned to Mora Armatur for recycling.

References

• Mora Armatur - Mixers for kitchens and bathrooms

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>