HYPERGEAR Stealth 2 ANC Wireless Headphones User Manual

June 13, 2024
HyperGear

HYPERGEAR Stealth 2 ANC Wireless Headphones

HYPERGEAR Stealth 2 ANC Wireless Headphones

OVERVIEW

Overview

  1. Voice Microphone
  2. ANC Button
  3. LED Indicator
  4. USB-C Charging Port
  5. AUX Input
  6. Volume Down/Previous Track
  7. Multifunction Button
  8. Volume Up/Next Track
  9. Power Button

GETTING STARTED

Charging Your Headphones

NOTE : Fully charge your headphones before first use.

Connect to a USB power source using the included USB-C charging cable.

Charging
Fully Charged (approximately 1.5 hours)

Pairing Your Headphones

  1. Make sure the headphones are powered off before beginning. Then, hold the Power Button for 5 seconds to enter Pairing Mode. The LED indicator will blink BLUE and RED to indicate that it is ready to pair.
  2. Open the Bluetooth menu on your phone, tablet, or computer. Enable searching for nearby Bluetooth devices.
  3. Select “Stealth ANC” to pair your headphones.
  4. Once connected, the LED indicator will blink BLUE every 6 seconds while powered on.

Your headphones will automatically reconnect to your phone, tablet, or computer the next time you turn your headphones on.

FUNCTIONS

|
---|---
Power On
Power Off| Hold (2 Sec)
Hold (3 Sec)
|
Active Noise Cancelling On/ Off| Press lx
Function Icon
Volume Down
Previous Track| Press lx
Hold (1 Sec)
Function Icon
Play/ Pause
Answer/ End Call
Reject Call
Activate Voice Assistant
Game Mode On / Off| Press lx
Hold (2 sec)
Press 2x
Press 3x
Function Icon
Volume Up
Next Track| Press 1x
Hold (1 Sec)

NOTES

Bluetooth Multipoint

Your headphones can remember 2 devices at once.
However, they can only play audio from one device at a time, even if 2 devices are connected.

To switch the active connection between devices, turn off the Bluetooth functionality on the primary device, or simply power off the device. Your headphones will automatically switch over to the secondary device.

If you wish to un-pair your headphones from a device, find your headphones in your device’s Bluetooth menu and select “Forget This Device” or “Forget”.

Low Battery

When the battery level is low, the LED indicator will blink RED.

Battery-Safe Charging

When plugged in and charging, the Bluetooth connection will be paused and the ANC function will be disabled. Once unplugged, the headphones will automatically power off. Press and hold the power button for 2 seconds to turn them back on, and they will automatically reconnect to their last paired device.

Aux Mode
Use any standard 3.5mm aux cord to connect your headphones to other audio sources, including non-Bluetooth devices. When plugged in via aux, the Bluetooth and Active Noise Cancelling functions are disabled. Use the audio controls on your source device instead.
IMPORTANT : The headphones must be powered off before Aux Mode can be used.

Need help? Visit www.myhypergear.com for additional product information or contact info@myhypergear.com

IMPORTANT

Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in damage, excess heat, toxic fumes, fire, explosion, electrical shock, or other hazards causing serious and/ or fatal injury and/ or property damage that is not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.

  1. Permanent hearing loss may occur if you listen at high volumes. Set the volume to a safe level.
  2. Maintain volume levels that allow you to hear sound around you and be alerted to potentially hazardous situations.
  3. Do not store the device in a depleted state. Battery cells may be damaged. Charge your unit at least once every 3 months even when not in use.
  4. Do not store at extreme temperatures (below 40° F or above 90° F). Battery cells may be damaged.
  5. Recharge your device with the included USB-C charging cable or a certified 3rd party cable and a 1A charging adapter. Less powerful adapters may charge the battery too slowly and damage/overheat the battery or cause a fire hazard.
  6. Unit is not waterproof. Do not submerge or expose to corrosive materials. Do not clean with harsh chemicals, soaps, or detergents.
  7. Do not attempt to modify, disassemble, or repair this product.
  8. Avoid excessive drops, bumps, and abrasions.
  9. If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
  10. temperature, emitting odor, deformed, abraded, or demonstrating an abnormal phenomenon, discontinue use immediately.
  11. Disposal of the unit in th1e garbage is unlawful under state and federal environmental laws and regulations.

Contact info@myhypergear.com to submit a warranty claim. Proof of purchase is required.

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information
The device was evaluated to meet general RF exposure requirements. This equipment should be installed and used with a minimum distance of 0mmbetween the radiator and your body

www.myhypergear.com

HYPERGEAR Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals