SEALEY 9602L Type 5-6 Disposable Coverall Instructions
- June 13, 2024
- SEALEY
Table of Contents
SEALEY 9602L Type 5-6 Disposable Coverall
Product Information
The Type 5/6 Disposable Coverall is a high-quality product manufactured by Sealey. It is designed to provide protection and comfort during various tasks. The coverall is made with a microporous film that allows breathability, ensuring comfort even during extended use. The coverall is available in two sizes: Large (Model No: 9602L) and Extra Large (Model No: 9602XL). It features elasticated wrists, ankles, hood, and waist section for a secure fit. The coverall weighs 65gsm, providing a lightweight and comfortable wearing experience.
Product Usage Instructions
- Before using the coverall, consult with qualified safety personnel to ensure that the coverall type and rating offer adequate protection for your intended use.
- The coverall is suitable for single use only and should not be re-used.
- When using the coverall with other personal protective equipment (PPE), such as gloves, boots, and respiratory protection, ensure that all openings like wrists, ankles, and neck are securely taped to comply with EN requirements for Type 5/6 garments.
- The user should judge the suitability of the coverall for the type of protection required and select the correct combinations of coverall accessories and ancillary equipment.
- If the coverall becomes contaminated, worn, or damaged, it should be promptly removed and disposed of properly.
- Before wearing the coverall, always check its integrity to ensure it is in good condition.
- In very warm conditions, consider the possibility of heat stress. Use appropriate undergarments and ventilation equipment to reduce or eliminate heat stress.
- Avoid extreme heat and cold as they may affect the performance of the coverall.
- The coverall should not be used in situations where there is a risk from hazardous chemicals that have not been tested against. Refer to the physical performance of the coverall in relation to Type 5 and 6 testing.
- Ensure that compatible chemical-resistant gloves, boots, and respiratory protection are worn along with the coverall. The gloves should cover the elastic cuffs and allow unrestricted movement for the intended task.
- If you need further advice or assistance, please contact the manufacturer or distributor.
- It is recommended to use the product within 3 years from the date of manufacture/production written on the packaging.
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
- WARNING: Suitable for single-use only. DO NOT re-use.
- WARNING: A properly selected coverall is essential to protect your health. Before commencing any task, please consult with qualified safety personnel to ensure that the coverall type and rating offers adequate protection for your intended use.
- WARNING: For use only by trained and qualified personnel.
- WARNING: Restrictions on the coverall disposal depend solely on the contamination occurring during use.
- When using the coverall with other PPE and in order to comply fully with EN requirement for Type5/6 garments, all openings such as wrist, ankles, neck etc., should be securely taped.
- The user shall be the sole judge of the suitability for the type of protection required and the correct combinations of coveralls accessories and ancillary equipment.
- Upon contamination, wear or damage, the coverall should be removed and appropriately disposed of at the earliest opportunity.
- The wearer should always ensure to check the integrity of the coverall before wearing it.
- The possibility of heat stress should be considered in very warm conditions. Heat stress can be reduced or eliminated by the appropriate use of undergarments and ventilation equipment.
- Extreme of heat and cold may adversely affect the performance of this garment.
- The coverall should not be used where there is a risk to certain hazardous chemicals that have not been tested against. Although limited protection can be offered from various chemicals, please refer to the physical performance of the coverall in relation to Type 5 and 6 testing.
- The user must also wear compatible chemical-resistant gloves, boots and respiratory protection. The gloves should cover the elastic cuffs. An appropriate size should be selected by the user to allow for unrestricted movement for the intended task.
- If necessary please contact Manufacturer/Distributor for advice.
- It is recommended that the product be used within a period of 3 years from the date of manufacture/production written on the packaging.
INTRODUCTION
The microporous film makes the coverall breathable, ensuring comfort during
periods of extended use. Elasticated wrists, ankles, hood and waist section.
65gsm Microporous film.
SPECIFICATION
- Model No: ………………………………………………9602L, 9602XL
- Size 9602L Large (Chest/Height): ……….. 100-108/176-182cm
- Size 9602XL – Extra Large (Chest/Height):……….. 108-116/182-188cm
| Fabric Physical Properties | Class | |
|---|---|---|
| Abrasion Resistance | EN 530 Meth.2 | Class 1 |
| Flex Cracking Resistance | ISO 7854 B | Class 4 |
| Trapezoidal Tear Resist. MD | ISO 9073·4 | Class 2 |
| XD | Class 2 | |
| Puncture resistance | EN863 | Class 1 |
| Tensile Strength MD | ISO 13934-1 | Class 1 |
| XD | Class 1 | |
| Radioactive Protection | EN1073-2:2002 | Class 2 |
| Infective Resistance(solid particles} | ISO 22612 | Class 3 |
| Resistance to ignition | EN 13274-4 | Pass |
| Fabric Chemical Properties Test Method | Penetration | Repellency |
| Resistance to chemical EN 368 | ||
| Sulphuric acid 30% | Class 3 | Class 3 |
| Sodium Hydroxide 10% | Class 3 | Class 3 |
| o-Xylene | Class 3 | Class 3 |
| --- | --- | --- |
| Butance-1-ol | Class 3 | Class 3 |
| Whole Suit Test Performance | ||
| Type 5 Inward leakage | IL 82/90 ≤30% &TILS 8/10≤15% | |
| Method as defined by EN ISO 13982-1:2004 | Pass | |
| Type 6 Light spray | ||
| Method as defined by EN 13034:1005 | Pass | |
| En 14126:1003 | ||
| Barrier to infective agents | Pass | |
| En 1073-2:002 | ||
| Barrier to radioactive particulates | Pass | |
| EN 1149-5:2018 Anti-static | Pass | |
| Protection against Infective Agents EN14126 | ||
| ISO 16603 | CLASS 6 | |
| ISO 16604 | CLASS 6 | |
| EN ISO 22610 | CLASS 6 | |
| ISO 22611 | CLASS 6 | |
| ISO 22612 | CLASS 6 |
Approvals:
Shirley®, Notified Body2895 Port Tunnel Business Park, Office 13 Unit 21,
Dublin 17, ROI, Ireland. BTTG®, notified body 0338, Unit 6 Wheel Forge Way,
Trafford Park, Manchester, M17 EH, United Kingdom.
STORAGE
The coverall can be stored in accordance with normal storage practices in a dry environment away from sources of heat, light and direct sunlight.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR |
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>