HealthmateForever YK15AB TENS EMS Muscle Stimulator User Manual

HealthmateForever YK15AB TENS EMS Muscle Stimulator

Introduction

Thank you very much for using the HealthmateForever® TENS/PMS device. In order to use this device safely, please read this user manual carefully before your first use. Please keep this user manual with your device for future reference.

Intended Use of Device

• TENS
  To be used for temporary relief of pain associated with sore and aching muscles in the shoulder, waist, back, neck, upper extremities (arms), and lower extremities (leg) due to strain from exercise or normal household work activities.

• PMS
  It is intended to be used to stimulate healthy muscles in order to improve and facilitate muscle performance.

If you would like to know more information please visit our website www.healthmateforever.com

This part is about the safety information. It is intended to help you use it safely, prevent injury, and avoid situations that could result in damage to the device. It is important for you to read this information carefully.

Contraindications

Do not use this device if you have a cardiac pacemaker, implanted defibrillator, or other implanted metallic or electronic device. Such use could cause electric shock, burns, electrical interference, or death.

Warnings

1. The long-term effects of chronic electrical stimulation are unknown.
2. Stimulation should not be applied over the carotid sinus nerve, particularly in patients with a known sensitivity to the carotid sinus reflex.
3. Stimulation should not be applied over the neck or mouth. Severe spasms of the laryngeal and pharyngeal muscles may occur and the contractions may be strong enough to close the airway or cause difficulty in breathing.
4. Stimulation should not be applied transthoracically in that the introduction of electrical current into the heart may cause cardiac arrhythmias.
5. Stimulation should not be applied trans-cerebrally.
6. Stimulation should not be applied over swollen, infected, or inflamed areas or skin eruptions, e.g., phlebitis, thrombophlebitis, varicose veins, etc.
7. Stimulation should not be applied over or in proximity to, cancerous lesions

Precautions

1. The safety of this device for use during pregnancy has not been established.
2. Caution should be used for patients with suspected or diagnosed heart problems.
3. Caution should be used for patients with suspected or diagnosed epilepsy.
4. Caution should be used in the presence of the following:
   • When there is a tendency to hemorrhage following acute trauma or fracture
   • Following recent surgical procedures when muscle contraction may disrupt the healing process;
   • Over the menstruating or pregnant uterus;
   • Over areas of the skin that lack normal sensation.
5. Some patients may experience skin irritation or hypersensitivity due to the electrical stimulation or electrical conductive medium. The irritation can usually be reduced by using an alternate conductive medium, or alternate electrode placement.
6. Electrode placement and stimulation settings should be based on the guidance of the prescribing practitioner.
7. The device should be kept out of the reach of children.
8. The device should be used only with the leads and electrodes recommended for use by the manufacturer.
9. This device should not be used while driving, operating machinery, or during any activity in which involuntary muscle contractions may put the user at undue risk of injury.

Adverse Reaction

• Skin irritation and burns beneath the stimulation electrodes applied to your skin
• Headache and other painful sensations during or following the application of electrical stimulation near your eyes, to your head and face

You should stop using the device and consult with your physician if you experience any adverse reactions from the device. ***

Included in this package

• 1 TENS/PMS device
• 8 sets of self-adhesive electrode pads 1 ½ inches
• 4 sets of dual leads wire with dia. 3.5mm plug
• 3 AAA batteries
• User Manual
• Warranty Card
• Pads holder
• Gift box

Illustrations of the Device

Illustrations of the Accessories

Features of Product

• Back light
• A/B independent channels
• 4 outputs which can output 100% power
• Use AAA battery
• Default 80 minutes timer
• 15 operating modes
• Independent intensity for A and B channels
• Easy to operate

How to Use the Device

Before using the device, please check the following information carefully:

1. Check the pads for any damages or irregularities.
2. Check the electrode wires for any damages or irregularities.
3. Check the device for any damages.

Please make sure the device Is OFF when setting up the device, adjusting the pads, or making a new connection. eat at one paid pee see pod alone dil on our skin.

1. Step 1: Set up batteries

   • Check if the batteries are in good condition
   • Remove the battery cover on the back of the device
   • Insert batteries. Make sure the “+” “-” sides correspond
   • Put the battery cover back.

2. Step 2: Connect electrode wires with the device.
   YK15AB has two independent channels A&B and 4 outputs A1, A2, B1, and B2. Make sure which channels (channel A or B) you want to use before you connect wires to the device.

   • If you want to use channel A only, please connect wire to outputs A1 A2.
   • If you want to use B channel only, please connect wire to outputs B1 B2.
   • If you would like to use both A and B channels, please connect wires to all outputs.
   1. Plug the electrode wire into the output located at the top of the device. Depending on your needs, you may use up to four outputs.
   2. Ensure that the electrode wires are fully inserted and secured.
   3. Repeat steps 1 and 2 to connect another wire.

3. Step 3: Connect electrode pads with wires

4. Each wire has two leads with pin-inserted connectors. Plug the pin-insert wire connectors into the pin-insert pads.

5. Make sure at least one pair of pads are attached to the same wire.

6. Ensure that the pin-insert connections are fastened.

7. Remove the plastic films on the pads.

  * Check if the adhesive side of the pad is clean after removing the plastic film.
  * We recommend keeping the plastic films for storing the pads after usage.

4. Step 4: Place pads on your body.
   Place pads on the area you would like to treat. (Please check Pg 14 Pad Placement for more information) Place the adhesive side of pad on your skin.

   • Again, please make sure that you use one pair of pads at the same time.
   • Please make sure that at least two pads are connected to one wire.
   • Make sure your skin has been cleaned of all dirt, oil, or lotions.
   • Make sure the pads are adhered closely on your skin.
   • Do not overlap pads or place one pad on top of another one.
   • DO NOT place pads on the artery, throat, bones, or wound.
   • DO NOT place pads near the heart, on both sides of the thorax or chest.

5. Step 5: Turn on the device and select the channel

   • Push the “ON/OFF” switch located on the right side of the device to the ON position:
   • The device will start showing all icons for 2 seconds to ensure that all options are displayed properly.
   • Verify the channel indicator on the screen to make sure the device is on the same channel you want. If the “A” on the screen is blinking, channel A is working. If “B” is blinking, channel B is working. If you plug wire into A (B) output, you have to use A (B) channel.

6. Step 6: Select modes.

   • Select any mode you want to use and press the button. For example, if you would like to use “BACK” mode, you need to press the button “BACK” on the device.

7. Step 7: Adjust intensity and speed

8. YK15AB has A/B independent channels. The intensity can be adjusted independently for A and B channels. There are “Intensity +” and “Intensity -” buttons on both left side and right side of the device.

9. Please use the “Intensity +” and “Intensity -” buttons on the left side to adjust the intensity for Channel A (A1 A2 outputs).

10. Please use the “Intensity +” and “Intensity -” buttons on the right side to adjust the intensity for Channel B (B1 B2 outputs).

11. Press the intensity “+” button to increase the intensity, press the intensity – button to decrease the intensity.

12. If you need to adjust speed of the electronic pulse, press the speed “+” button to increase the speed, and press Speed “-” button to decrease the speed.

  * • We suggest you try from the lowest intensity and gradually increase the intensity to a level you feel comfortable.
  * • The intensity should be set at a level where you will experience some muscular vibration and involuntary muscle movements.

8. Step 8: Adjust timer
   This model has a default 80-minute timer. Timer will be the same for both A, B channels. You CANNOT adjust the timer separately for A, B channels.

9. Step 9: Turn off the device
   Push the “ON/OFF” switch located at the right side of the device to the OFF position.

10. Step 10: Remove the pads from your skin.
    Remove the pads from your skin softly and place them back on the provided pad holder or the protective plastic film.

    • • DO NOT remove the pads before you turn off the device.

11. Step 11: take off the pads from the wires. Unplug wires from the device.

Cleaning and Storage

Device Use a lightly moistened cloth to clean the device and wipe gently.

• Make sure the device is off when you clean it.
• Do not let water get into the device.

Cleaning and Storing Pad

Clean: After using pads on your body, please drop a little clean water on the sticky side and use your fingertips to clean it softly

• Please turn off the device and disconnect the pads with wires first before you clean the pad.
• Do not use nails or other sharp objects on the sticky side.
• Do not use chemical liquids on the sticky side.

Storage: Place pads on the pad holder or place the plastic film on the sticky side of the pad to keep the gel moist.

Wires: You can wrap wires on the pad holder

• Do not keep the device in areas subject to direct sunlight, high or low temperatures, humid areas, or near fire, vibration, or shock.
• Do not keep the device in places that can be easily reached by children.

Mode Description

• a selection of the modes ly at gives you use most desired i sensations and Comtor 15 the most appropriate one to use for your current therapy session.
• Recommended application duration is 2-3 times per day for 40-60 minutes per application, over 10 days for one course

Pad Placement

• LOWER BACK
  Attach both pads on the lower back with the backbone in the center. Do not place it on the backbone or spine. Suggested Mode Mode 3, 10, 11, 13, and 14

• SCIATIC
  Attach on pad below and above the region in pain, both on the same side(NOT on the spine). Suggested Mode Mode 3, 5, 10, 12, 13, and 14

• DELTOID
  Attach one pad in front and one in the back of the muscle. Suggested Mode Mode 3, 5, 10, 12, 13, and 14

• UPPER ARM
  Attach both pads on either side of the region where you feel pain. Suggested Mode Mode 2, 10, 11, 12, 13 and 14

• ELBOW
  Attach both pads on either side of the joint with the pain. Suggested Mode Mode 4, 11, 12 and 14

• HIP & THIGH
  Attach both pads on either side of the area with pain. Suggested Mode Mode 5, 10, 13 and 14

• KNEE
  Attach both pads above the knee or above and below the joint with pain. Suggested Mode Mode 1, 7, 12, 13 and 14

• CALF
  Attach both pads on the calf/leg where you feel pain. (Do no place pads simultaneously to the calves of both legs) Suggested Mode Mode 7, 10, 13 and 14

• ABS/SHOULDER
  Attach pads per the illustration. (Do not put pads on the spine) Suggested Mode Mode 3, 10, 11, 13 and 14

• ANKLE/FOOT
  Attach pads on the left for pain on the outside. Attach pads on the right for pain on the inside Suggested Mode Mode 8, 10, 12, 14 and 15

Trouble Shooting

One pad feels stronger than the other.

| This is normal. Different areas of your body will react

differently.

| Nothing needs to be done. Make sure the pads are moist and are making good contact.

During the massage, the skin feels a painful burning sensation or the stimulation becomes weakened.

| ****

Adhesive gel pads are not adhering firmly to the skin. The gel pads are

too dry .

wires are damaged

| ****

Apply a few drops of water to adhesive surtace of each pad and make sure the pads are pressed firmly to the skin during application. Use a new set of pads.

Use a new set of wires.

Unit is on, but no sensation is felt in the pads

| ****

Both pads are not firmly on the skin. There is a loose connection.

The intensity level needs to be increased

| Make sure both pads are firmly pressed to the skin. (two pads minimum) One pad alone will not work.

Make sure all connections are secure from the unit to the wires and the wires to the pads.

Increase the intensity level

Adhesive gel pads do not stick to skin even after cleaning and moistening the gel pad.| ****

Adhesive material ran out.

| ****

Adhesive gel pads need to be replaced.

You can purchase at www.HealthmateForever.com

Unit does not turn on or the screen is dim.| ****

Battery is low

| ****

Change the battery

Unit does not charge

| Wall adapter or USB cord.| Charge your unit using USB cord only using any USB power outlet.

Only feel stimulation one channel

| Your device features the AB independent channel.

Bad wire.

| ****

Try to set the mode and/or the intensity on each channel.

Try to use a new set of wires.

Please feel free to contact us by sending emails to support@healthmateforever.com or calling toll free 888-860-7788 if you need further assistance.

Warranty

Please visit our website www.healthmateforever.com for more information about the warranty policy. Please feel free to contact us by calling toll free 888-860-7788 or sending emails to support@healthmateforever.com if you have any question about warranty. We are always happy to assist you.

Specification

Output Parameters

• Output pulse width: 90uS ≤ 15%
• Pulse frequency: < 100Hz
• The maximum output amplitude: < 5V(r.m.s)

Input Parameters

• Input voltage: DC4.5V
• Rated current: ≤ 50mA
• Rated power: ≤ 0.25W

Medical Disclaimer

• All information is intended for you general knowledge only and is not a substitute for medical advice or treatment for specific medical conditions. We cannot and do not give you medical advice. You should seek prompt medical care for any specific health issues and consult your health care provider before purchasing any products). The information contained here is intended to provide broad consumer understanding and knowledge of the product offered.
• The information should not be considered complete and should not be used in place of a visit, call, consultation, or advice or your health care provider. Should you have any healthcare-related questions, please call or see your healthcare provider promptly. You should never disregard medical advice or delay in seeking it because of something you have read here.

Contact

• Email: support@healthmateforever.com
• Toll free: 888-860-7788
• Website: www.healthmateforever.com
• Working hours: 9:00am-5:00pm Monday-Friday CST except weekend and holidays.

FREQUENTLY ASKED QUESTIONS

How does the HealthmateForever YK15AB TENS EMS Muscle Stimulator provide pain relief?

The HealthmateForever YK15AB TENS EMS Muscle Stimulator delivers electrical impulses through the skin via electrode pads, stimulating nerves and muscles to alleviate pain and promote muscle relaxation.

What are the specific uses of the HealthmateForever YK15AB TENS EMS Muscle Stimulator?

The HealthmateForever YK15AB TENS EMS Muscle Stimulator can be used for various purposes including relieving back pain, knee pain, ankle pain, and providing general pain relief.

What are the package dimensions and weight of the HealthmateForever YK15AB TENS EMS Muscle Stimulator?

The HealthmateForever YK15AB TENS EMS Muscle Stimulator has package dimensions of 9.33 x 7.24 x 1.54 inches and weighs approximately 1 pound, ensuring portability and ease of use.

What type of power source does the HealthmateForever YK15AB TENS EMS Muscle Stimulator use?

The HealthmateForever YK15AB TENS EMS Muscle Stimulator is battery-powered, requiring 3 AAA batteries for operation.

Who is the manufacturer of the HealthmateForever YK15AB TENS EMS Muscle Stimulator?

The HealthmateForever YK15AB TENS EMS Muscle Stimulator is manufactured by Healthmate International, LLC, a trusted company known for producing quality health and wellness products.

What is the price of the HealthmateForever YK15AB TENS EMS Muscle Stimulator?

The price of the HealthmateForever YK15AB TENS EMS Muscle Stimulator is $37.00, offering an affordable solution for pain management.

Does the HealthmateForever YK15AB TENS EMS Muscle Stimulator come with a warranty?

Yes, the HealthmateForever YK15AB TENS EMS Muscle Stimulator comes with a 2-year warranty, providing users with confidence in the product's quality and durability.

How does the HealthmateForever YK15AB TENS EMS Muscle Stimulator differ from traditional pain relief methods?

Unlike traditional pain relief methods such as medication or heat therapy, the HealthmateForever YK15AB TENS EMS Muscle Stimulator provides drug-free pain relief through electrical stimulation, which can be more targeted and personalized.

Can the HealthmateForever YK15AB TENS EMS Muscle Stimulator be used for prolonged periods?

Yes, the HealthmateForever YK15AB TENS EMS Muscle Stimulator can be used for prolonged periods as directed, providing continuous pain relief and muscle stimulation. However, it's essential to follow the recommended guidelines and take breaks as needed to prevent overuse.

What should I do if my HealthmateForever YK15AB TENS EMS Muscle Stimulator is not turning on?

If your HealthmateForever YK15AB TENS EMS Muscle Stimulator is not turning on, ensure that the batteries are correctly inserted and have enough charge. Try replacing the batteries with new ones to rule out any power issues. If it still doesn't turn on, contact Healthmate International, LLC for assistance.

How can I troubleshoot if my HealthmateForever YK15AB TENS EMS Muscle Stimulator is not providing any stimulation?

If your HealthmateForever YK15AB TENS EMS Muscle Stimulator is not providing stimulation, check if the electrode pads are correctly connected and placed on your skin. Adjust the intensity levels and try different modes. If there's still no stimulation, contact Healthmate International, LLC for support.

What should I do if my HealthmateForever YK15AB TENS EMS Muscle Stimulator is emitting an unusual smell or overheating?

If your HealthmateForever YK15AB TENS EMS Muscle Stimulator is emitting an unusual smell or overheating, immediately turn it off and disconnect it from the batteries. Allow it to cool down and inspect for any signs of damage. Contact Healthmate International, LLC for troubleshooting and avoid using it until the issue is resolved.

How can I troubleshoot if my HealthmateForever YK15AB TENS EMS Muscle Stimulator is causing discomfort or skin irritation?

If your HealthmateForever YK15AB TENS EMS Muscle Stimulator is causing discomfort or skin irritation, ensure that the electrode pads are clean and properly placed. Lower the intensity levels and use a conductive gel if necessary. If irritation persists, discontinue use and seek advice from Healthmate International, LLC.

What should I do if my HealthmateForever YK15AB TENS EMS Muscle Stimulator is not charging or holding a charge?

If your HealthmateForever YK15AB TENS EMS Muscle Stimulator is not charging or holding a charge, check the battery compartment for any debris or corrosion. Ensure the batteries are inserted correctly and try using different batteries or a new charging cable.

How can I troubleshoot if my HealthmateForever YK15AB TENS EMS Muscle Stimulator is displaying error codes?

If your HealthmateForever YK15AB TENS EMS Muscle Stimulator is displaying error codes, refer to the user manual to identify the specific code and its meaning. Follow the troubleshooting steps provided. If you're unable to resolve the issue, reach out to Healthmate International, LLC for assistance.

VIDEO – PRODUCT OVERVIEW

DOWNLOAD THE PDF LINK: HealthmateForever YK15AB TENS EMS Muscle Stimulator User Manual

REFERENCE:HealthmateForever YK15AB TENS EMS Muscle Stimulator User Manual- Device.Report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>