AG DIESEL SOLUTIONS 62540 Module for 2021-2023 Ford 3.5L and 2.7L EcoBoost Installation Guide
- June 13, 2024
- AG DIESEL SOLUTIONS
Table of Contents
AG DIESEL SOLUTIONS 62540 Module for 2021-2023 Ford 3.5L and 2.7L
EcoBoost
Product Information
| Product Name | 62540 Module |
|---|---|
| Installation Guide | 2021-2023 |
| Horsepower Gain | Up to 45HP |
| Fuel Savings | 1-3 MPG |
| Manufacturer Website |
Product Usage Instructions
- Remove the engine shield to gain access to the MAP & T-MAP Sensor connectors. This can be done by removing two 10mm nuts.
- Locate the MAP & T-MAP Sensors. The MAP Sensor can be found on top of the intake manifold. The T-MAP Sensor can be found near the throttle body inlet.
- Disconnect the stock male MAP sensor connector.
- Utilize the portion of the Ag Diesel Solutions harness labeled MAP. Connect the male connector to the MAP Sensor. Then connect the ADS female connector to the stock male MAP Sensor connector.
- Disconnect the stock male T-MAP Sensor connector from the T-MAP Sensor.
- Utilize the portion of the Ag Diesel Solutions harness labeled T-MAP. Connect the male connector to the T-MAP Sensor. Then connect the female connector to the stock male T-MAP Sensor connector.
- Remove the bypass plug from the Ag Diesel Solutions harness, and plug the harness into the module. Note: Keep the bypass plug for potential troubleshooting.
- Mount the module box in a safe location using the zip ties to secure the wires and module away from any extreme heat and moving parts. Note: Mounting the module with the connector down will help prevent moisture from collecting into the module connector.
- Connect module switch harness. Based on preference, the module switch can be secured in the engine compartment near the module or it can be routed into the cab. If mounting in the cab, route the Switch through the firewall and connect to the module harness.
Important: This is a high-performance product. Use at your own risk. Please read and understand the following agreement before using this product.
Disclaimer of Warranty and Limitation of Liability: Limited 3-year warranty is provided. If you do not agree with this agreement, you can return the product within 30 days of purchase for a full refund in a new and unused condition, in the original packaging, with a dated proof of purchase.
Effective Date: 11/1/2022
OVERVIEW
- A bypass plug is included with the module for potential troubleshooting. Install bypass plug in module connector to return vehicle to stock functionality if needed.
- Make sure to push completely together until connector snaps when using bypass plug.
For Tech Support Please Call
- 812-618-9168
- PSI Power recommends removing the Ag Diesel Solutions module before any warranty work is performed on the piece of equipment the module is installed on.
Adjustable on the fly
-
Position 1- Stock (counter clockwise)
-
Position 2- Low- up to 15HP
-
Position 3- Medium- Up to 30HP
-
Position 4- High- Up to 45HP
-
Position 1- Switch far left
-
Position 4- Switch far right
-
Module switch can be ran inside the cab for easy performance adjustment. Module switch can be secured in engine bay if desired. Module will default to HIGH setting if switch is not connected
-
NOT FOR USE IN CALIFORNIA^
-
MODULE DOES NOT BYPASS, DELETE, OR DEFEAT ANY EMISISON CONTROL SYSTEMS
-
If installation assistnace is needed, Ag Diesel Solutions is not responsible for any cost associated with third party installation.
Instructions
-
Remove the engine shield to gain access to the MAP & TMAP Sensor connectors. This can be done by removing two 10mm nuts.
-
With the cover removed, locate the MAP & T-MAP Sensors. The MAP Sensor can be found on top of the intake manifold. The T-MAP Sensor can be found near the throttle body inlet.
-
Disconnect the stock male MAP sensor connector.
-
Utilize the portion of the Ag Diesel Solutions harness labeled MAP. Connect the male connector to the MAP Sensor. Then connect the ADS female connector to the stock male MAP Sensor connector.
-
Disconnect the stock male T-MAP Sensor connector from the T-MAP Sensor.
-
Utilize the portion of the Ag Diesel Solutions harness labeled TMAP. Connect the male connector to the T-MAP Sensor. Then connect the female connector to the stock male T-MAP Sensor connector.
-
Remove the bypass plug from the Ag Diesel Solutions harness, and plug the harness into the module.
Note: Keep the bypass plug for potential troubleshooting. -
Mount the module box in a safe location using the zip ties to secure the wires and module away from any extreme heat and moving parts. Note:Mounting the module with the connector down will help prevent moisture from collecting into the module connector.
-
Connect module switch harness. Based on preference, the module switch can be secured in the engine compartment near the module or it can be routed into the cab. If mounting in the cab, route the Switch through the firewall and connect to the module harness.
THIS IS A HIGH-PERFORMANCE PRODUCT. USE AT YOUR OWN RISK
Do not use this product until you have carefully read the following agreement. This sets forth the terms and conditions for the use of this product. The installation of this product indicates that the BUYER has read and understands this agreement and accepts its terms and conditions.
WARRANTY
DISCLAIMER OF WARRANTY AND LIMITATION OF LIABILITY
PSI Power, Inc and its successors, distributors, jobbers, and dealers
(hereafter “SELLER”) shall in no way be responsible for the product’s proper
use and service. It is the installer’s responsibility to check for proper
installation and if in doubt, contact the manufacturer. The SELLER assumes no
liability regarding the improper installation or misapplication of its
products.
BUYER ACKNOWLEDGES IT HAS HAD THE OPPORTUNITY TO FULLY INSPECT THE PRODUCT.
ACCORDINGLY, BUYER ACKNOWLEDGES THAT THE PRODUCT IS BEING SOLD IN “AS IS/WHERE
IS” CONDITION AND WITH ALL FAULTS. EXCEPT AS OTHERWISE PROVIDED HEREIN, THERE
ARE NO EXPRESS WARRANTIES WITH RESPECT TO THE GOODS, AND ALL IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO, IMPLIED WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIKEWISE HEREBY EXPRESSLY AND FULLY
DISCLAIMED. SELLER SHALL NOT BE HELD LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY NATURE WITH RESPECT TO THE PRODUCTS
(INCLUDING, WITHOUT LIMITATION, LOST PROFITS, LOST SALES, LOSS OF PRODUCTION,
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OR DAMAGE RESULTING FROM INTERRUPTION
OR FAILURE IN OPERATION OF THE PRODUCTS) AND BUYER HEREBY EXPRESSLY WAIVES AND
DISCLAIMS ALL SUCH LIABILITY CLAIMS. THE BUYER ACKNOWLEDGES AND AGREES THAT
THE DISCLAIMER OF LIABILITY CONTAINED HEREIN IS A MATERIAL TERM OF THE SALE OF
THE PRODUCT AND, TO THE FULLEST EXTENT PERMITTED BY LAW, BUYER SHALL DEFEND,
INDEMNIFY AND HOLD SELLER HARMLESS FROM ANY AND ALL CLAIMS, DEMANDS, CAUSES OF
ACTION, CONTROVERSIES, LIABILITIES, FINES, LOSSES, COSTS AND EXPENSES
(INCLUDING, BUT NOT LIMITED TO ATTORNEYS’ FEES, EXPERT WITNESS EXPENSES AND
LITIGATION EXPENSES) ARISING FROM OR RELATED TO SELLER’S PRODUCTS.
LIMITED 3 YEAR WARRANTY
PSI Power, INC. (hereafter “SELLER”) warrants that the product supplied shall conform to SELLER’s specifications and shall be free from defects in design, material or workmanship for 3 years to the original BUYER. This warranty shall not be extended, transferred, assigned or varied except by a written instrument signed by SELLER and BUYER. Products that have been returned to SELLER during the warranty period and accompanied by a dated proof of purchase receipt, with shipping and handling paid by the BUYER, and found to be defective in design, material, or workmanship, in SELLER’s sole discretion, may be repaired or replaced at SELLER’s option and cost. All warranty claims hereunder are subject to approval by SELLER upon examination of the product. If the product is found not to be defective by SELLER, the product may be returned to BUYER at BUYERS cost. Under no circumstances shall the SELLER be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or reinstallation of this product or any other expenses. This warranty is void on any products that show evidence of misapplication, negligence, improper installation, abuse, lack of proper maintenance or alteration from its original design.
IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS AGREEMENT, THE BUYER MAY PROMPTLY RETURN THIS PRODUCT, IN A NEW AND UNUSED CONDITION, IN THE ORIGINAL PACKAGING, WITH A DATED PROOF OF PURCHASE, TO THE PLACE OF PURCHASE WITHIN (30) DAYS FROM THE DATE OF PURCHASE FOR A FULL REFUND. THE INSTALLATION OF THIS PRODUCT INDICATES THAT THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND ACCEPTS ITS TERMS AND CONDITIONS Effective 11/1/2022.
- UP to 30% HORSEPOWER INCREASE
- UP To 10%-20% IN FUEL SAVINGS
- DOES NOT FLASH THE FACTORY ECM
- FIELD TESTED & DYNO PROVEN
- PLUG & PLAY INSTALLATION
Performance Electronics for Agriculture, Forestry, Construction, Pick-Up Trucks, Medium Duty Trucks, RVs, Heavy Duty Semis, and more!
LEARN MORE: AGDIESELSOLUTIONs.COM.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>