AG DIESEL SOLUTIONS 62560 2.0L Ford EcoBoost Installation Guide
- June 12, 2024
- AG DIESEL SOLUTIONS
Table of Contents
AG DIESEL SOLUTIONS 62560 2.0L Ford EcoBoost
Product Information
The 62560 Module is a high-performance product designed for the 2020-2023 2.0L Ford Eco Boost engine. It offers up to 45HP gain and 1-3 MPG fuel savings. The module is manufactured by AgDieselSolutions.com and comes with a bypass plug for troubleshooting purposes.
Product Usage Instructions
- Locate the MAP sensor on the top of the intake manifold on the passenger side of the engine bay. Also, locate the T-MAP sensor on the charge pipe towards the front, center of the engine bay.
- Disconnect the stock MAP sensor connector by pulling back on the locking tab and squeezing the connector release tab.
- Utilize the portion of the Ag Diesel Solutions harness labeled MAP. Connect the male connector to the MAP Sensor. Then connect the ADS female connector to the stock male MAP Sensor connector.
- Disconnect the stock T-MAP sensor connector by pulling back on the locking tab and squeezing the connector release tab.
- Utilize the portion of the Ag Diesel Solutions harness labeled T-MAP. Connect the male connector to the T-MAP Sensor. Then connect the female connector to the stock male T-MAP Sensor connector.
- Remove the bypass plug from the Ag Diesel Solutions harness and plug the harness into the module. Keep the bypass plug for potential troubleshooting.
- Mount the module box in a safe location using zip ties to secure the wires and module away from extreme heat and moving parts. Mounting the module with the connector down will help prevent moisture from collecting into the module connector.
- Connect the module switch harness. The module switch can be secured in the engine compartment near the module or routed into the cab. If mounting in the cab, route the switch through the firewall and connect it to the module harness.
Important
This is a high-performance product. Use at your own risk. Please read and
understand the following] agreement and terms and conditions before using the
product.
Disclaimer of Warranty and Limitation of Liability
The product comes with a limited 3-year warranty. If you do not agree with
the agreement, you can return the product within 30 days from the date of
purchase for a full refund, provided it is in a new and unused condition and
in the
original packaging. By installing this product, you indicate that you have
read, understood, and accepted the terms and conditions of this agreement.
- Effective Date: 11/1/2022
A bypass plug is included with the module for potential troubleshooting. Install bypass plug in module connector to return vehicle to stock functionality if needed
Make sure to push completely together until connector snaps when using bypass plug.
For Tech Support Please Call
812-618-9168 PSI Power recommends
removing Ule Ag Diesel Solutions modulR before any warranty work is perlormod
on the piece of equipment t he module 1s ins talled on.
Module switch can be ran in,1ide the cab for easy performance adjustment.
Module switch can be secured In engine bay If desired. Module will default to
HIGH settinQ if switch is not connected
~NOT FOR USE IN CALIFORNIA~
AMOOULE DOES NOT BYPASS, DELETE, OR DEFEAT ANY EMl:SISON CONTROL SYSTEMSi
- If inslal1Qtion TissistnE1ce is neaded, Ai;;i Diesel Solution~ is not ~:;.ponsible for TI”Y oost ar.sociatecl with third osirtv inSWlletion.
20-23 2.0L Ford EcoBoost Engine Installation Instructions
-
LLocate MAP sensor on top offthe intake manifold on passenger side of the engine bay. Locate the-T-MAP sensor on charge pipe towards the front, center of engine bay.
-
Disconnect stock MAP sensor connector by pulling back on locking tab and squeezing the connector release tab.
-
Utilize the portion of the Ag Diesel Solutions harness labeled MAP. Connect the male connector to the MAP Sensor. Then connect the ADS female connector to the stock male MAP Sensor connector..
-
Disconnect stock T-MAP sensor connector by pulling back on locking tab and squeezing the connector release tab.
-
Utilize the portion of the Ag Diesel Solutions harness labeled T-MAP. Connect the male connector to the T-MAP Sensor. Then connect the female connector to the stock male T-MAP Sensor connector.
-
Remove the bypass plug from the Ag Diesel Solutions harness, and plug the harness into the module.
Note: Keep the bypass plug for potential troubleshooting. -
Mount the module box in a safe location using the zip ties to secure the wires and module away from any extreme heat and moving parts. Note:Mounting the module with the connector down will help prevent moisture from collecting into the module connector.
-
Connect module switch harness. Based on preference, the module switch can be secured in the engine compartment near the module or it can be routed into the cab. If mounting in the cab, route the Switch through the firewall and connect to the module harness.
THIS IS A HIGH PERFORMANCE PRODUCT. USE AT YOUR OWN RISK
- Do not use this product until you have carefully read the following agreement. This sets forth the terms and conditions for the use of this product. The installation of this product indicates that the BUYER has read and understands this agreement and accepts its terms and conditions
DISCLAIMER OF WARRANTY AND LIMITATION OFLIABILITY
PSI Power, Inc and its successors, distributors, jobbers, and dealers
(hereafter “SELLER”) shall in no way be responsible for the product’s proper
use and service. It is the installer’s responsibility to check for proper
installation and if in doubt, contact the manufacturer. The SELLER assumes no
liability regarding the improper installation or misapplication of its
products. BUYER ACKNOWLEDGES IT HAS HAD THE OPPORTUNITY TO FULLY INSPECT THE
PRODUCT. ACCORDINGLY, BUYER ACKNOWLEDGES THAT THE PRODUCT IS BEING SOLD IN “AS
IS/WHERE IS” CONDITION AND WITH ALL FAULTS. EXCEPT AS OTHERWISE PROVIDED
HEREIN, THERE ARE NO EXPRESS WARRANTIES WITH RESPECT TO THE GOODS, AND ALL
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIKEWISE HEREBY
EXPRESSLY AND FULLY DISCLAIMED. SELLER SHALL NOT BE HELD LIABLE FOR SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE WITH RESPECT TO
THE PRODUCTS (INCLUDING, WITHOUT LIMITATION, LOST PROFITS, LOST SALES, LOSS OF
PRODUCTION, PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OR DAMAGE RESULTING FROM
INTERRUPTION OR FAILURE IN OPERATION OF THE PRODUCTS) AND BUYER HEREBY
EXPRESSLY WAIVES AND DISCLAIMS ALL SUCH LIABILITY CLAIMS. THE BUYER
ACKNOWLEDGES AND AGREES THAT THE DISCLAIMER OF LIABILITY CONTAINED HEREIN IS A
MATERIAL TERM OF THE SALE OF THE PRODUCT AND, TO THE FULLEST EXTENT PERMITTED
BY LAW, BUYER SHALL DEFEND, INDEMNIFY AND HOLD SELLER HARMLESS FROM ANY AND
ALL CLAIMS, DEMANDS, CAUSES OF ACTION, CONTROVERSIES, LIABILITIES, FINES,
LOSSES, COSTS AND EXPENSES (INCLUD-ING, BUT NOT LIMITED TO ATTORNEYS’ FEES,
EXPERT WITNESS EXPENSES AND LITIGA-TION EXPENSES) ARISING FROM OR RELATED TO
SELLER’S PRODUCTS.
LIMITED 3 YEAR WARRANTY
PSI Power, INC. (hereafter “SELLER”) warrants that the product supplied shall conform to SELLER’s specifications and shall be free from defects in design, material or workmanship for 3 years to the original BUYER. This warranty shall not be extended, transferred, assigned or varied except by a written instrument signed by SELLER and BUYER. Products that have been returned to SELLER during the warranty period and accompanied by a dated proof of purchase receipt, with shipping and handling paid by the BUYER, and found to be defective in design, material, or workmanship, in SELLER’s sole discretion, may be repaired or replaced at SELLER’s option and cost. All warranty claims hereunder are subject to approval by SELLER upon examination of the product. If the product is found not to be defective by SELLER, the product may be returned to BUYER at BUYERS cost. Under no circumstanc-es shall the SELLER be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or reinstallation of this product or any other expenses. This warranty is void on any products that show evidence of misapplication, negligence, improper installation, abuse, lack of proper maintenance or alteration from its original design.
IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS AGREEMENT, THE BUYER MAY
PROMPTLY RETURN THIS PRODUCT, IN A NEW AND UNUSED CONDITION, IN THE ORIGINAL
PACKAGING, WITH A DATED PROOF OF PURCHASE, TO THE PLACE OF PURCHASE WITHIN
(30) DAYS FROM THE DATE OF PURCHASE FOR A FULL REFUND. THE INSTALLATION OF
THIS PRODUCT INDICATES THAT THE BUYER HAS READ AND UNDER-STANDS THIS AGREEMENT
AND ACCEPTS ITS TERMS AND CONDITIONS
Effective 11/1/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>