AGPTEK BTS141 Speaker User Manual

BTS141 User Manual

BTS141 Speaker

Thank you for purchasing AGPTEK product. Please read this [User Manual] carefully before using the product, retain it in for future use.
Note:
To find out how to use S2 or if you have a problem, please refer to User Manual.
This [User Manual] can help you understand how to use and troubleshoot the problem.
For better use this product, please connect the speaker to computer with USB 2.0/3.0 port or a 5V/1A charger (not quick charger) by the included USB cable. Usually, it will be fully charged in 3hours.

Register AGPTEK Forum
Please visit www.agptek.com/forum and register AGPTEK official forum to get better customer support.
Manufacturer: Betrue Technology Company Limited.
Address: D07, 5/F, King Yip Factory Building, 59 King Yip Street, Kwun Tong, Kowloon, Hong Kong.
E-mail: support@agptek.com.

Buttons & Controls

LED Digital Screen

After booting up this product, this speaker will display the Time Calibration Interface ❶ firstly. Press M button to cycle through different interface, such as Bluetooth Mode ❷, FM Function ❸, TF Card Mode ❹ (Available when TF card is inserted).

Time Calibration

1. In power on mode, press the “ M ” to switch to clock mode if it is in other mode.
2. Press and hold the “ M ” to go to hour set, the number of hour will blink on LED display.
3. Press the “ ” or “ ” button for adjusting the hour time as current time.
4. Short press the “ ” button to confirm the hour time set and go for Minute set. The number of minute will blink on LED display.
5. Press the “ ” or “ ” button for adjusting the minute time as current time.
6. Short press the “ ” button to confirm the minute time set.

Note:

1. For maintain the battery life and performance, if speaker isn’t used for a while, the battery might need to be recharged. Charge the battery at least once every month.
2. Connect the Micro USB socket with the PC’s USB port Power or DC 5V, 1000mA through USB cable. Note: Please tighten the Rubber Seal Cover after charging to prevent water from penetrating nto the speaker.
3. Disconnect the USB cable when it is done.

Playing Music Via Bluetooth

• Power on and Pairing
  1. Press and hold button to turn on the device. A series of tones will sound. If it is in clock mode, press button M to switch to Bluetooth mode, the icon is blinking quickly.
  2. Then turn on your device’s Bluetooth, the device will enter to Bluetooth searching mode automatically, if not, please search manually, then tap the related selection to manually enter to searching mode. (Refer to the user manual when necessary).
  3. Your device show “AGPTEK S2” to select it for pairing. Waiting for some seconds, you will see connected message as shown on your device. (For some Bluetooth devices, you may need to input “0000” as pairing password).
  4. If pairing is successful, the icon will constantly show on the display. Then you can start to play music by the device.
  5. Press and hold to turn off the device when it is not in use.

• Disconnect from paired device
  1. Press and hold to switch to new “Searching/Pairing” mode, the paired device will be disconnected. Or, you can choose “Disconnect” from Bluetooth paired device list on your mobile device.
  In this case; the Bluetooth Speaker will turn back into “Searching/Pairing” mode in seconds, a series of tones will sound and the is blinking fast.
  2. Now, you can process for new mobile device pair or power off the Bluetooth Speaker.
  Note: If Bluetooth is not connected for more than 8 minutes, this device will shut down automatically.

• Auto re-connect with paired device and New pairing
  1. Every time you turn on the speaker and enter into Bluetooth mode; it will firstly searching for the mobile device, which has been paired previously and still in record. The Speaker will re-connect this mobile device as priority if it is in Bluetooth searching device mode.
  2. If not found in some seconds, the Bluetooth Speaker then is turn into new pairing mode internally.
  3. Now you can process for new mobile device pair. (Refer to “Power on and Pairing”)

• After Bluetooth Paring
  After Bluetooth pairing, the speaker can be operated by the following buttons while playing music.press | to pause/resume the music
  ---|---
  Press +| increase the volume level
  Press –| decrease the volume level
  Press | go to next music
  Press | go to previous music

Note: When maximum or minimum volume is reached, a series of tones will sound.

Call Function

• About how to use Hand free Function
  When there is an incoming call during Bluetooth music playing mode;
  The ringing sound will up and the playing music will pause automatically.

And the paused music will start to play automatically
Press and hold button for 3 seconds| ignore the incoming call

Tip: speak to the MIC hole directly with distance in 30~60cm to get the best speakerphone performance when necessary.

• Redial for last call Function
  To redial for last called number by the Speaker, even it is in music playing mode.Press the for twice| enter into redial function, the playing music will pause and switch to hand free function for redial.
  ---|---
  Press the again| hang up the redial call

Note: Make sure that your mobile phone has have last dial call used, if not, the redial for last call function cannot be activated.

FM Function

• Auto Tune Radio Frequency:
  In Bluetooth mode, press button M to enter into FM mode.
  Press and hold button to enter into auto searching mode.
  (1) The FM radio will search up the frequency from 87.5 MHz to 108.0MHz and will save the searched stations automatically.
  (2) When finished searching, it will play from the firstly searched station automatically. You can select radio station P01-P40 through the “ ” or “ ” button, and press the “ ” button again to confirm.

• FM playing control:
  To switch back to Bluetooth mode, press twice button

M.

How to set the clock

1. In time mode, press and hold “ ” button to enter alarm clock set. “AL” will show on the screen. You can press the “ ” button to turn ON the alarm clock.
2. When “ON” show on the screen, press “ ” button to go to hour set.
3. Press or pressing the “ ” or “ ” button for adjusting the hour time as you desired.
4. Short press the “ ” button to confirm the hour time set and go for Minute set. The number of minute will blink on LED display;
5. Press or pressing the “ ” or “ ” button for adjusting the minute time as you desired.
6. Short press the “ ” button to confirm the minute time set.
7. When the alarm is set, it will emit a series of beeps and then adjust the alarm volume.
8. Press or pressing the “ + ” or “ – ” button for adjusting the volume level as you desired.
9. Short press the “ ” button to confirm the volume level and the volume of alarm clock set is completed.
10. Press once “ ” button to stop the alarm.

Low Power Reminder and Auto Sleep

1. The Bluetooth Speaker will send tones from speaker by every minute. When you heard this reminder, please connect the device to the USB power for charging, if you still want to use the device.
2. If not, the Bluetooth Speaker will power off automatically when the battery is keeping low energy level in some minutes.
3. In this case, the device cannot be turned on, until you recharging the battery at least 10~15 minutes, because the rechargeable battery has not enough energy.

Reset the Device

1. In some circumstances the device’s function may hanging and need to reset. To reset the Bluetooth speaker;
2. Insert a needle into reset hole near Micro USB socket. Then the device will reset automatically.
3. After that, turn on the Bluetooth Speaker by press and hold button .

Note: Do not reset the device if it is in properly working.

Splash Proof Handling

The Bluetooth Speaker can handle a brief jet of water on its surface (IPX5 water resistant). However, it should never be operated under running water and under no circumstance it should never be fully immersed in water. Before use the Shower Bluetooth speaker in bathroom, make sure that the splash proof “Rubber Seal Cover ” is tighten closed at the right position.
After used in bathroom, always wipe the outside of the cabinet thoroughly if it becomes wet with moisture or water splashes. This will help to prevent the internal parts of the unit from entry of water and possible moisture damage.
Note: If water get into the USB socket, please always clean the water thoroughly before charging the device.

Specifications

Dimension| 80(L)x35(W)x95rnm(H)
(Not include Vacuum Cupule)
---|---
Weight| 149g (Approximate)
Bluetooth| Specification| V5.0
Supported Profile| WAV/FLAC/APE/ WMA/FIA/NWT/ AMR/DTS
Effective Distance| 20m(In open area)
FM Radio| Tuning Range| 87.5— 108MHz
Presets| up to 40 stations
Antenna| Wireless type
Built-In Battery| Lithium3.7V, 2000mAh
Charging Time: around 3 H
Playing Time: around 10.5-12H (at max. volume setting, Bluetooth mode)
Power| Micro USB Port
Source| PC’s USB port Power or DC 5V, 1A
Water Resistance| Splash-Proof IPX5
Operating Temperature| 0 to 40°C

References

• Agptek forum - Index
• Agptek forum - Index

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>