TORRO SP-01039 2.4GHz Remote Control Instruction Manual
- June 5, 2024
- TORRO
Table of Contents
SP-01039 2.4GHz Remote Control
Instruction Manual
TORRO GmbH, D-63762 Groflostheim. Any publication, reproduction, distribution,
or commercial use us subject to written consent. All article names and
pictures or illustrations are property of the respective manufacturer or of
TORRO GmbH. Copyright is extended to translations and layout. All contents of
the manual are subject to change. No liability is assumed for changes and
errors.
Frequency 2.4 GHz approved for EU / CH
ATTENTION
An important supplement to the manual of your RC model. Do read this
supplement and the manual carefully and entirely before operating the model
and the remote control.
IMPORTANT INFORMATION
Telecommunication Regulations:
When using a remote control device, please do observe the current legislation
of the country in the device is being used in! If you have any questions,
please contact our service (see box bottom right) or your local dealer.
Declaration of Conformity
This RC model conforms with all relevant German laws and all basic
requirements and regulations of the RED directive 2014/53/EU of the European
Community. This model contains a transmitter + receiver! If you have any
questions regarding the conformity or if you wish to exercise your right of
access or if you want to download the declaration, please go to:
www.torro.de/zertifikate
– www.torro.de/en/certificates
Notes for disposal of batteries and electronic parts:
Please, do the deposit of battery packs, batteries, and all electronic parts
(remote control, charger, RC model, etc.) according to local laws and
regulations. Protect the environment.
Product Questions / Customer Complaints
Please, do contact our service department if you have any questions or a
complaint. Do not send in items before having contacted our service department
via telephone, fax, or e-mail.
Torro GmbH
Am Rahrig 2 D-63762 GROSSOSTHEIM
Fax: +49 (0) 6026 9990482
E-Mail: service@torro.de
www.torro.de
SAFETY NOTES AND DISCLAMER OF LIABILITY
These safety instructions serve your own safety and that of other persons.
Please read these safety instructions carefully! We assume no liability for
damage caused by non-observance of these operating instructions, the guarantee
or warranty as well as for damage and consequential damage. We also accept no
liability for damage to property or personal injury caused by improper
handling or non-compliance with the safety instructions! Excluded from the
guarantee and warranty are normal wear and tear during operation and
accidental damage such as torn-off receiver antennas, broken receiver housing,
lost or broken gear stick, battery covers, etc.
Dear customer,
– The product is not a toy, it is not suitable for children under the age of
14.
– For safety and approval reasons, unauthorized modifications and/or changes
to the product are not permitted.
– The product must not be wet, damp or soiled and must not be exposed to
direct sunlight or extreme heat for long periods of time.
– It is recommended that you take out personal liability insurance. If you
already have one, find out whether the operation of a radio-controlled model
is also covered by insurance. – Keep the product and packaging material away
from children.
– The operation and operation of remote-controlled models must first be
learned! If you have never remote-controlled a model before, you should start
very carefully and only become familiar with the model’s reactions to the
remote control commands. The easiest way is to have an experienced technician
show and explain the operation and operation to you.
– If you have any questions that cannot be answered with the help of the
operating instructions or if you do not have sufficient knowledge of remote-
controlled models and remote controls, please contact our service department,
another specialist or a model building club.
– Always switch on the remote control first when putting the receiver into
operation. Only then may the receiver in the model be switched on. Otherwise,
unpredictable reactions of the model may occur!
– Before operating the receiver on a stationary model, check whether it reacts
as expected to the remote control commands.
– When operating a model, always ensure that body parts, children, animals, or
objects are never within the danger zone of motors or other rotating drive
parts.
– Improper operation can cause serious personal injury and damage to property!
– In the event of a malfunction, stop operating your model immediately and
eliminate the cause of the malfunction before continuing to use the model.
– Control the model only if your ability to react is unrestricted. Fatigue,
alcohol, or medication influence can lead to false reactions and accidents.
– Only operate the model in an area where you do not endanger other persons,
animals, or objects. Only in private or specially designated places and always
maintain visual contact with the model.
– Do not operate your remote control system during lightning storms, under
power lines, or near radio masts. Especially not near airports.
– Keep the remote control switched on while the model is in operation. If you
want to end the use, always switch off the motor first and then switch off the
receiver system. Only then may the remote control be switched off.
– Weak batteries in the remote control (or in the receiver system) reduce the
range and the model no longer responds correctly to the remote control. In
this case, stop driving immediately and replace the batteries of the remote
control or the receiver system with new ones (or recharged ones in the case of
battery operation).
– Responsible handling of the remote control and the model is essential to
protect yourself and your environment!
CAUTION NOTES. PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE.
INTENDED USE
Please observe all safety instructions in this operating manual. It contains
important instructions for the operation and handling of this 8-channel remote
control. The product must not be modified or technically changed. You alone
are responsible for the safe operation of your remote control! This 8-channel
remote control is only to be used for its intended purpose, exclusively for
private use in a model building with the associated operating time.
The 8-channel remote control is not suitable for commercial/industrial use,
e.g. control of systems or machines, as its use for such purposes can lead to
damage to the products involved and considerable dangers such as fire, short
circuit, electric shock, etc. The 8-channel remote control is not suitable for
commercial/industrial use, e.g. control of systems or machines.
Operation Instructions
Tank Engine Startup and Stop-Process :
-Turn the tank and transmitter on.
-Flip the left toggle back towards yourself to start the tank.
-Flip the left toggle switch away from yourself to stop the tank.
Code Binding
The tanks are bound at the factory and tested at our warehouse before shipping
and a no-bind process out of the box should be needed. However, if you are
having issues starting the tank with the stock transmitter then a rebound will
most of the time solve this issue. Please follow the instruction below.
-Turn the tank on.
-Within 5 seconds turn the transmitter on while holding down the machine gun button on the right side of the transmitter. The transmitter LED status light will start to blink fast for a few seconds.
-After the LED light has stopped blinking you can then flip the left toggle switch towards yourself and start the tank.
- Main Power Input
- Infrared Receiver & Emitter
- LED Flasher & Recoil (Airsoft users for 2 right pins only)
- Sound Card Port
- Transmitter Selection
- Motor right
- Motor left
- External Receiver Channel 1-6
- Upper Hull 8-Pin-Plug
- Smoke Unit 2-Pin-Plug
- Tank Tail-Light(upgradeable)
- Volume Adjustment
- Speaker
BOARD WIRING
NO 1 . : External socket NO 1-6 channels
Caution: Please notice those wires installed direction, the white color
wire are most inside the socket.
NO 2 . : External signal wire ( Available for another brand of hobby
transmitter only )
Caution: If take another brand of hobby transmitter, please installed the
external signal wire
NO 3 .: Infrared connection wire
Caution : Please notice for infrared battle system only.
2.4 GHZ DIGITAL CONTROL PACKAGE
A three-part set comprising a digital transmitter, receiver/control unit, and
speaker.
The 2,4GHz band covers the frequencies from 2,4 to 2,4835GHz providing up to
80 channels with a maximum transmitter power of 100mW ERP. Frequency selection
is automatic(no crystals required).
The receiver/control unit replaces the RX18 mainboard in Heng Long tanks and
the receiver board, features include a built-in fan. Tanks fitted with this
system no longer require an aerial.
The transmitter frequency has been factory set to work with the receiver. A
simple process allows users to bind the transmitter to other Taigen receivers
which may have a different frequency.
Please note that the transmitter will only function with the new Taigen
receiver/control unit and cannot be used with old Heng Long versions such as
the RX18.
This system is suitable for use with both infrared and BB firing Heng Long
tanks. For infrared battling each tank will need to have this system
installed, it will not be possible for a tank with this new system to battle
against an infrared tank that has different electronics.
Owners of BB firing tanks should note that the BB switch on the tank needs to
be in the “on” position in order for the main gun firing sound and track
recoil to function.
The included speaker has a higher performance than the standard Heng Long
speaker.
Specifications: 3W, frequency 150Hz-15kHz, size 5,8cm x 5,8cm.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>