SUNGROW AC011E-01 AC Charger Installation Guide
- June 4, 2024
- SUNGROW
Table of Contents
Quick Installation Guide
AC Charger
AC011E-01
AC011E-01 AC Charger
- The contents of the document will be periodically updated or revised due to product development. It is probable that there are changes to the document in the subsequent edition. Under no circumstances can this document replace the user manual and the safety instructions on the product.
- Please read the user manual and relevant standards and specifications carefully before performing any operation. You can get the information by logging in Sungrow support platform via http://support.sungrowpower.com/ or scanning the QR code on the side of the product or on the back cover of the quick installation instruction.
- All operations shall only be performed by professional personnel. Professional personnel must be trained specially, read this instruction thoroughly, master the safety instructions related to the operation and be familiar with the local standards and safety regulations of the electrical system.
- Before installing the equipment, check whether the goods are complete and consistent with the order and whether there is obvious damage according to the packing List. Contact the shipping company or SUNGROW directly in case of any damage or incompleteness.
- Cables used for the charger must be intact and well-insulated. Use insulation tools and wear personal protective equipment.
- Violation of any of the above requirements may cause casualties or equipment damage.
Safety Statement
Failure to comply with the requirements of this document and the user manual may cause casualties or equipment damage, and Sungrow shall not assume any liability.
DANGER
High voltages are present during operation and could cause electrical shock,
resulting in death, serious personal injury, or property damage.
Non-professional personnel shall not disassemble the components.
CAUTION
Keep the charger away from flammable and explosive substances. Store it in a
dry, clean, and well-ventilated place, free from harmful gases. Do not store
it near corrosive objects.
NOTICE
- During transport, the charger shall be securely packed and marked in the loading direction in a wooden box, and the charger shall not be stored upside down.
- During transport, tighten the equipment to avoid violent shaking and bumps that damage the package.
- After the arrival of goods, check for transport damage and, if any, contact the shipping company or us.
- Check if the devices inside the package are the same as that of the delivery list.
Scope of delivery:
Tools:
Mounting place
Dimensions and weight
| Name | Weight |
|---|---|
| AC011E-01 | 3.8kg (with plugs) |
Cable connection²
Note: cable shall be connected before the charger is installed. Cable
cross-section: 5×2.5mm
Wall-mounted charger installation
Before drilling, avoid the water and electricity wiring in the wall to prevent hazards. The drill size isΦ6mm and the drilling depth is about 45mm. The bearing capacity of the installation carrier shall be at least 4.5 times that of the charger!
② Install the socket-out.(It is recommended that the socket-out be installed at the lower right side of the charger, with a linear distance of about 20cm from the charger. The actual situation on site shall prevail.）
Pile-mounted charger installation (optional)
The drill size isΦ12mm and the drilling depth is about 85mm.
Inspection before commissioning
No.|
Item
|
Judgment
---|---|---
Yes
|
No
1| The charger is installed securely.| □| □
2| The installation place is convenient for operation and maintenance.| □| □
3| Cable is connected correctly and firmly.| □| □
4| With sufficient cooling space.| □| □
5| Cables are routed safely and protected against mechanical damage.| □| □
Commissioning
Step 1 Confirm that all inspected items meet the requirements before
commissioning;
Step 2 Close the cable inlet leakage protection circuit breaker;
Step 3 Power on the charger: about one minute of power-on self-test time;
Step 4 After the power-on self-test, observe the status of the indicators.
The status description of the LED indicators are shown in the table below.
| Charger status | Indicator |
|---|---|
| Standby | Blue indicator flashes slowly, on for 1s and off for 4s; circulating |
| Charging (S2 is closed and current is normal) | Blue indicator breathes, on for |
1s and off for 1s; circulating
Charging stops| Blue indicator is steady on
Detecting plug| Red indicator is steady on
Ground cable and live cable connected reversely| Blue indicator flashes
quickly, on for 0.5s and off for 0.5s; circulating
Power-on self-test| Blue indicator is on for 1s and red indicator is on for 1s
Charger software upgrading| Blue indicator flashes quickly
More information in the QR code or
at http://support.sungrowpower.com/
Sungrow Power Supply Co., Ltd.
QIEN M-H-002590
Add: No.2 Tianhu Rd., New & High Technology Industrial Development Zone,
Hefei, P.R.China.230088
Web: www.sungrowpower.com
E-mail: info@sungrow.cn
Specifications subject to change without notice.
Documents / Resources
|
SUNGROW AC011E-01 AC
Charger
[pdf] Installation Guide
AC011E-01 AC Charger, AC011E-01, AC Charger, Charger
---|---