SUNGROW SG5KTL-MT PV Grid-Connected Inverter Installation Guide

SUNGROW SG5KTL-MT PV Grid-Connected Inverter

1.  Contents may be periodically updated or revised due to product development. The information in this guide is subject to change without notice. In no case shall this guide substitute for the user manual or related notes on the device.

2. Make sure to read over, fully understand and strictly follow the detailed instructions of the user
   manual and other related regulations. Visit http://www.sungrowpower.com/, choose “PV Inverters” and search for the device model on the ” Products ” tab page to view or obtain the user manual.

3.  All operations can be performed only by qualified personnel, that must be trained in the installation and commissioning of the electrical system, as well as the dealing with hazards, have knowledge of the manual and of the local regulations and directives.

4.  Before installation, check that the package contents are intact and complete against the packing list. Contact SUNGROW or the distributor in case of any damaged or missing components.

5.  The cable must be intact and well insulated. Operation personnel must wear proper personal protective equipment (PPE) all the time.

6.  Any violation could result in personal death or injury or device damage, and will void the warranty.

Safety

The inverter has been designed and tested strictly according to international safety regulations. Read all safety instructions carefully prior to any work and observe them at all times when working on or with the inverter. Incorrect operation or work may cause:

•  injury or death to the operator or a third party; or
•  damage to the inverter and property safety of the operator or a third party.

Please follow the safety instructions related to the PV strings and the utility grid.

DANGER

•  PV strings will produce electrical power when exposed to sunlight and can cause a lethal voltage and an electric shock.
• Only qualified personnel can perform the wiring of the PV panels.

NOTICE

• All electrical connections must be in accordance with local and national standards.
•  Only with the permission of the utility grid, the inverter can be connected to the utility grid.

The warning label on the inverter body are as follows.

• Disconnect the inverter from all the external power sources before service!
• Do not touch live parts until 1 0 minutes after disconnection from the power sources.
• There is a danger from a hot surface that may exceed 60 ° C.
• Danger to life due to high voltages! Only qualified personnel can open and service the inverter.

DANGER

Danger to life from electric shocks due to live voltage

• Do not open the enclosure at any time. Unauthorized opening will void guarantee and warranty claims and in most cases terminate the operating license.
•  When the enclosure lid is removed, live components can be touched which can result in death or serious injury due to electric shock. Danger to life from electric shock due to damaged inverter
• Only operate the inverter when it is technically faultless and in a safe state.
•  Operating a damaged inverter can lead to hazardous situations that can result in death or serious injuries due to electric shock.

WARNING

Risk of inverter damage or personal injury

• Do not pull out the PV connectors and AC connector when the inverter is running. Disconnect the AC circuit breaker and set the DC load-break switch of the inverter to OFF. Wait 1 O minutes for the internal capacitors to discharge. Verify that there is no voltage or current before pulling any connector.

WARNING

All the warning labels and nameplate on the inverter body:

•  must be clearly visible; and
• must not be removed, covered or pasted.

CAUTION

Risk of burns due to hot components!

• Do not touch any hot parts (such as heat sinks) during operation. Only the DC switch can safely be touched at any time.

NOTICE

Only qualified personnel can perform the country setting. Unauthorized alteration of the country setting may cause a breach of the type-certificate marking. Risk of inverter damage due to electrostatic discharge (ESD). By touching the electronic components, you may damage the inverter. For inverter handling, be sure to:

•  avoid any unnecessary touching; and
•  wear a grounding wristband before touching any connectors.

Scope of Delivery

Mounting location

Installation tools

Use appropriate mounting hardware for wall type.

Meter Connection

Power on

LED indicator panel

Documents / Resources

| SUNGROW SG5KTL-MT PV Grid-Connected Inverter [pdf] Installation Guide
SG5KTL-MT PV Grid-Connected Inverter, SG5KTL-MT, PV Grid-Connected Inverter
---|---
| SUNGROW SG5KTL-MT PV Grid-Connected Inverter [pdf] Installation Guide
SG5KTL-MT PV Grid-Connected Inverter, SG5KTL-MT, PV Grid-Connected Inverter

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>