saxby lighting 102669 OrbitalPRO 4CCT Light Instruction Manual

: June 13, 2024
: saxby lighting

Table of Contents

saxby lighting 102669 OrbitalPRO 4CCT Light
Product Usage Instructions
Installation
Wiring
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

saxby lighting 102669 OrbitalPRO 4CCT Light

Product Information

The OrbitalPro 4CCT is a light fitting that operates on a supply voltage of 220-240 V~ and 50 Hz frequency. It uses a 9W LED module (SMD) with color temperature options of 2700K, 3000K, 4000K, and 6000K. The light source is non-replaceable, but the control gear can be replaced by a professional. The product is compliant with all relevant UKCA and EC Directive requirements. It is double insulated and does not require connection to an Earth circuit. The product is fire rated for 30, 60, and 90 minutes and has an IP65 rating, making it suitable for use in outdoor zones and Zone 2 of a bathroom. The product can be dimmed and should be cleaned with a soft dry cloth.

For more information, visit https://www.lighting-info.co.uk/102669.

Manufacturer: BH17 7BY (UK), Brilliant AG, Brilliantstrasse 1,D-27442 Gnarrenburg (EU)

Product Usage Instructions

Unclip the cover from the quick fit connection block at the end of the driver.
Identify the wiring of your existing light fitting.
Pull the mains wire through the hole and connect it to the connection block inside the quick fit connection case in the following way:
- SUPPLY: Insert cable for the mains wire.
- PUSH DOWN: Push down the connection block.
- LIGHT FITTING: Connect the wires from your existing light fitting.
- NEUTRAL EARTH (GREEN/YELLOW) FOR TERMINATION: Connect the neutral earth wire.
- SWITCHED LIVE: Connect the switched live wire.
- L (BLUE): Connect the blue wire.
- N (BROWN): Connect the brown wire.
Check that:
- You have correctly identified the wires.
- The connections are tight.
- No loose strands have been left out of the connection block.
Plan the desired layout of the fittings, ensuring the cables will reach the distances between the transformer and each light fitting.
Avoid locating cables in positions that may cause hazards.
Position cables and junction boxes away from areas where they may be at risk of being cut, trapped, or damaged.
Ensure the mains supply cable has a minimum cross-section area of 1.0mm2.
Protect cables using suitable conduit or plastic trunking.
Mount the unit a minimum distance of 50mm from a joist.
Maintain a minimum distance of 0.5m between units.
Mount the product out of arm’s reach.
The product can be covered with insulation up to 270mm.
For installation in a room containing a bath or shower, use a 30mA RCD in accordance with IEE regulations.
Before installing the new product, completely remove any existing fittings and note the position of each set of wires.
Ensure the ceiling surface is flat and smooth for a good fit.
Turn off the switch before installation.
Seal the screws and cable entry points to maintain the IP rating of the product.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This light fitting is double insulated and does not require connection to an earth circuit.

Please read these instructions carefully before commencing any work
This unit must be ﬁtted by a competent and qualiﬁed electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
This system operates at Safety Extra Low Voltage, via the supplied LED driver, Never connect the light fittings directly to the mains without using the supplied LED driver.
Always disconnect the LED driver from the mains when installing or maintaining this system.
To prevent electrocution switch off at the mains supply before installing or maintaining this ﬁtting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light ﬁtting should be connected to a fused circuit.
If replacing an existing ﬁtting, make a careful note of the connections.
This product complies with Building Regulations Part B and is suitable for use in 30, 60 & 90 minute fire rated ceilings.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout
Plan the desired layout of these ﬁttings carefully, ensuring the cables will reach the distances between the transformer and each light ﬁtting.
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.

The mains supply cable must have a minimum cross section area of 1.0mm2. Cables must be protected using suitable conduit or plastic trunking.
The unit must be located a minimum distance of 50mm from a joist.
The distance between units must be 0.5m minimum.
This product must be mounted out of arms reach.
This product is suitable for covering with insulation 270mm.
This product is suitable for use in outside zones of a bathroom and Zone 2. Please see diagram.
If this unit is being ﬁtted in a room containing a bath or shower, a 30mA RCD must be used – in accordance with IEE regulations.

Installation

Existing ﬁttings must be completely removed before installation of a new product. Before removing the existing ﬁtting, carefully note the position of each set of wires.
The ceiling surface must be ﬂat and smooth to ensure a good ﬁt.
Note that the switch is turned off before installation.
Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.

This product is colur changing and can be either warm white (2700/3000K) or cool white (4000K) or daylight white (6000K). Choose your preferred colour before installing by using the CCT switch.

Owing to its unique construction and heat dissipation the product can be covered directly with insulation when installed in the ceiling. Ensure a minimum ceiling void depth of 45mm is available.

Position the LED Driver next to mains outlet that the system will connect to do not connect at this stage.

Cut a mounting hole 97mm diameter in the ceiling taking care not to foul any pipes, mains cables or joists beneath the surface. It is always recommended to cut the hole slightly smaller than the size specified, and then file the hole until the recessed unit fits snugly.

Push the spring clips upwards and fit into the ceiling hole.
Push the unit up until firmly in position. Ensure that the product is fitted properly in the hole.
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Wiring

Unclip the cover from the quick fit connection block at the end of the driver. Having correctly identified the wiring form your existing light fitting, pull the mains wire through the hole and connect to the connection block inside the quick fit connection case in the following way.

Check that…

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.

Technical data

Supply Voltage: 220-240 V~, 50 Hz
Bulb Type: 9W LED module (SMD) CCT, 2700/3000/4000/6000K

This product contains a light source of energy efficiency class F.

Non-replaceable light source

Replaceable control gear by a professional

Conformity with all relevant UKCA Directive requirements.

Conformity with all relevant EC Directive requirements.

The power supply is Double Insulated and does not require connection to an Earth circuit.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

This product is suitable for dimming.

This product fire rated to 30, 60 & 90 minutes.

This product is rated at IP65.

Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the ﬁnish. For your safety, always switch off the power supply before cleaning.

For further information, please visit https://www.lighting-info.co.uk/102669

V1 30/06/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

www.saxbylighting.com